Manufacture of thermoplastic elastomer tubes by water assisted injection molding technology

Rubber Chemistry and Technology

Volumn 81, Issue 1, 2008, Pages 156-167

  Liu, Shih Jung ^a   Lin, Kun Yeh ^a   Liu, Che Chi ^a  

^a CHANG GUNG UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

ELASTOMERS; ETHYLENE; MANUFACTURE; MOLDING; MOLDS; OIL WELL FLOODING; PLASTICS; PROCESSING; REINFORCED PLASTICS; STYRENE; THERMOPLASTIC ELASTOMERS; WATER INJECTION; WATER TANKS;

GAS-ASSISTED INJECTION MOLDING; INJECTION MOLDED PART; PRESSURE ACCUMULATORS; PRINCIPAL FACTORS; PROCESSING PARAMETERS; RESIDUAL WALL THICKNESS; WATER PENETRATION; WATER-ASSISTED INJECTION MOLDING;

INJECTION MOLDING;

EID: 58149498422     PISSN: 00359475     EISSN: None     Source Type: Journal    
DOI: 10.5254/1.3548194     Document Type: Article

References (21)

1. M. Knights, Plast. Technol. Sept., 54 (2005).
2. W. Michaeli, T. Juntgen and A. Brunswick, Kunstst. Plast. Europe 91(3), 37 (2001).
3. S. J. Liu and Y. S. Chen, Polym. Eng. Sci. 43, 1806 (2003).
4. Y. C. Wu and S. J. Liu, Plast. Rubber Comp. 34, 227 (2005).
5. W. Michaeli, Water Injection Technique, Chapter 6, Injection Molding-Fundamental and Applications, Kamal, Isayev and Liu Ed., Hanser, Munich (in press).
6. S. Shah, SPE-ANTEC Tech. Paper 37, 1494 (1991).
7. L. S. Turng, Adv. Polym. Tech. 14, 1 (1995).
8. S. Y. Yang, S. J. Liou, and W. N. Liou, Adv. Polym. Tech. 16, 175 (1997).
9. A. J. Poslinski, P. R. Oehler and V. K. Stokes, Polym. Eng. Sci. 35, 877 (1995).
10. S. C. Chen, K. F. Hsu and K. S. Hsu, Num. Heat Trans. 28, 121 (1995).
11. H. Potente, E. Moritzer, C. H. Oberman, Polym. Eng. Sci. 36, 2163 (1996).
12. nd1 Ed., Van Nostrand Reihhold, New York (1988).
13. N. R. Legge, G. Holden, H. E. Schroeder, Thermoplastic Elastomers: A Comprehensive Review, Hanser, New York (1987).
14. S. K. De, A. K. Bhowmick, Thermoplastic Elastomers from Rubber-Plastic Blends, Ellis Horwood, New York (1990).
15. E. Haberstroh and I. Kleba, J. Polym. Eng. 24, 361 (2004).
16. Everlon, Ever Polymer CO., Taiwan.
17. S. J. Liu, S. P. Lin, Comp. Part A 36, 1507 (2005).
18. S. J. Liu, and W. K. Chen, Plast. Rubber Comp. 33, 260 (2004).
19. S. J. Liu and J. H. Chang, Polym. Comp. 21, 322 (2000).
20. S. J. Liu and Y. C. Wu, Inter. Polym. Proc 15, 297 (2000).
21. S. J. Liu, and C. Y. Yang, Plast. Rubber Comp. 31, 36 (2002).