Occurrence of surface roughness in gas assist injection molded nylon composites

Polymer Composites

Volumn 21, Issue 2, 2000, Pages 322-331

  Liu, Shih Jung ^a   Chang, Jer Haur ^a  

^a CHANG GUNG UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

INJECTION MOLDING; MOLDS; MOLTEN MATERIALS; NYLON POLYMERS; PLASTIC PARTS; PLASTICS MOLDING; SCANNING ELECTRON MICROSCOPY; SURFACE ROUGHNESS;

GAS ASSIST INJECTION MOLDING;

GLASS FIBER REINFORCED PLASTICS;

EID: 0033899097     PISSN: 02728397     EISSN: None     Source Type: Journal    
DOI: 10.1002/pc.10189     Document Type: Article

References (29)

1. S. Shah, SPE ANTEC Tech. Papers, 37, 1494 (1991).
2. L. S. Turng, Adv. Polym. Tech., 14, 1 (1995).
3. I. I. Rubin, Injection Molding - Theory and Practice, Wiley, New York (1972).
4. S. Y. Yang, F. Z. Huang, and W. N. Liau, Polym. Eng. Sci., 36, 2824 (1996).
5. S. Y. Yang , S. J. Liou, and W. N. Liou, Adv. Polym. Tech., 16, 175 (1997).
6. A. J. Poslinski, P. R. Oehler, and V. K. Stokes, Polym. Eng. Sci., 35, 877 (1995).
7. R. E. Khayat, A. Derduri, and L. P. Hebert, J. Non-Newtonian fluid Mech., 57, 253 (1995).
8. S. C. Chen, K. F. Hsu, and K. S. Hsu, Num. Heat Trans., 28, 121 (1995).
9. S. H. Parng and S. Y. Yang, Inter. Polym. Proc., 13, 318 (1998).
10. S. C. Chen, N. T. Cheng, and S. Y Hu, J. Appl. Polym. Sci., 67, 1553 (1998).
11. Y. S. Soh and C. H. Chung, J. Reinf. Plast. Comp., 17, 935 (1998).
12. Y. Y. Nie, L. S. Turng, and K. K. Wang, Adv. Polym. Tech., 16, 159 (1997).
13. X. Lu, H. H. Chiang, J. Zhao, and S. C. Chen, Polym. Eng. Sci., 38, 62 (1999).
14. G. A. A. V. Haagh, H. Zuidema, F. N. van de Vosse, G. W. M. Peters, and H. E. H. Meijer, Inter. Polym. Proc., 12, 207 (1997).
15. S. J. Liu, C. Y. Ho, J. H. Chang, and S. W. Hung, Inter. Polym. Proc., 14, 191 (1999).
16. D. Hull and T. W. Clyne, An Introduction to Composite Materials, 2nd Ed., Cambridge Solid State Science Series (1996).
17. Mapex, Ginar Chem. Co., Taiwan
18. R. Rothon, Particulate-Filled Polymer Composites, Longman, England (1995).
19. A. I. Isayev, Injection and Compression Molding Fundamentals, Marcel Dekker, New York (1987).
20. P. Gerald, J. Raine, and J. Pabiot, J. Reinf. Plast. Comp., 17, 922 (1998).
21. O. Becker, D. Karsono, K. Koelling and T. Atlan, SPE ANTEC Tech. Papers. 43, 615 (1997).
22. J. Ko and J. R. Youn, Polymer Composites, 16, 114 (1995).
23. J. P. Greene and J. O. Wilkes, Polym. Eng. Sci., 37, 1019 (1997)
24. L. Averous, J. C. Quantin, A. Crespy, and D. Lafon, Polym. Eng. Sci., 37, 329 (1997)
25. M. Saito, S. Kukula, and Y. Kataoka, Polymer Composites, 19, 497 (1998).
26. Z. Tadmor and C. G. Gogos, Principles of Polymer Processing, John Wiley & Sons, New York (1979).
27. K. Oda, J. L. White, and E. S. Clark, Polym. Eng. Sci., 16, 585 (1976).
28. L. C. Sawyer and D. T. Grubb, Polymer Microscopy, Chamman & Hall, New York (1994).
29. D. V. Rosato and D. V. Rosato, Plastics Processing Data Handbook, Van Nostrand Reinhold, New York (1990).