On the role of bubbles in metallic splat nanopores and adhesion

Journal of Thermal Spray Technology

Volumn 17, Issue 4, 2008, Pages 486-494

  Qu, Meng ^a   Gouldstone, Andrew ^b  

^a STONY BROOK UNIVERSITY   (United States)

^b Northeastern University   (United States)

Author keywords

Porosity of coatings; Roughness effects; Splats

Indexed keywords

BUBBLE GROWTHS; BUBBLE NUCLEATIONS; DRIVING FORCES; NANOPOROUS SURFACES; PORE FORMATIONS; PROCESS PARAMETERS; ROUGHNESS EFFECTS; SPLATS; SUB MICRONS; SURFACE AREA MATERIALS; SURFACE ROUGHENING; THERMAL PROPERTIES;

ADHESION; EXPERIMENTS; NANOPORES; NUCLEATION; PORE SIZE; SURFACES; THERMAL SPRAYING; THERMODYNAMIC PROPERTIES;

NANOSTRUCTURED MATERIALS;

EID: 56749169212     PISSN: 10599630     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11666-008-9198-9     Document Type: Article

References (38)

1. P. Gougeon, C. Moreau (2001) Simultaneous Independent Measurement of Splat Diameter and Cooling Time During Impact on a Substrate of Plasma-Sprayed Molybdenum Particles. J. Therm. Spray Technol, 10(1):76-82
2. P. Fauchais, M. Fukumoto, A. Vardelle, M. Vardelle (2004) Knowledge Concerning Splat Formation: An Invited Review. J. Therm. Spray Technol. 13(3):337-360
3. S. Sampath (1996) Rapid Solidification and Microstructure Development During Plasma Spray Deposition. J. Thermal Spray Technol. 5:445-456
4. M. Fukumoto, E. Nishioka, T. Matsubara (1999) Flattening and Solidification Behavior of a Metal Droplet on a Flat Substrate Surface Held at Various Temperatures. Surf. Coat. Tech 120:131-137
5. A. McDonald, M. Lamontagne, S. Chandra, C. Moreau (2006) Photographing Impact of Plasma-Sprayed Particles on Metal Substrates. J. Therm. Spray Technol 15(4):708-716
6. H. Zhang, X.Y. Wang, L.L. Zheng, X.Y. Jiang (2001) Studies of Splat Morphology and Rapid Solidification During Thermal Spraying. Int. J. Heat and Mass Transfer 44(24):4579-4592
7. H.B. Parizi, L. Rosenzweig, J. Mostaghimi, S. Chandra, T. Coyle, H. Salimi, L. Pershin, A. McDonald, C. Moreau (2007) Numerical Simulation of Droplet Impact on Patterned Surfaces. J Therm Spray Technol 16(6):713-721
8. M. Xue, S. Chandra, J. Mostaghimi (2006) Investigation of Splat Curling up in Thermal Spray Coatings. J. Therm. Spray Technol 15(4):531-536
9. H. Liu, E.J. Lavernia, R.H. Rangel (1995) Modeling of Molten Droplet Impingement on a Non-Flat Surface. Acta Metallurgica et Materialia 43(5):2053-2072
10. T. Chraska, A.H. King (2001) Transmission Electron Microscopy Study of Rapid Solidification of Plasma Sprayed Zirconia - Part Ii Interfaces and Subsequent Splat Solidification. Thin solid films 397(1-2):40-48
11. S. Deshpande, A. Kulkarni, S. Sampath, H. Herman (2004) Application of Image Analysis for Characterization of Porosity in Thermal Spray Coatings and Correlation with Small Angle Neutron Scattering. Surf. Coat. Tech. 187:6-16
12. S. Polarz, B. Smarsly (2002) Nanoporous Materials. J. Nanoscience and Nanotechnology 2(6):581-612
13. S. Zhang D., Sun Y., Fu H. Du (2003) Recent Advances of Superhard Nanocomposite Coatings: A Review. Surf. Coat. Tech. 167(2-3):113-119
14. C. L. Tien, G. Chen (1994) Challenges in Microscale Conductive and Radiative Heat Transfer. J. Heat Transfer-Trans. ASME 116(4):799-807
15. R. Yang, G. Chen, M.S. Dresselhaus (2005) Thermal Conductivity Modeling of Core-Shell and Tubular Nanowires. Nano Letters 5(6):1111-1115
16. Y.M. Chiang, D.P. Birnie, and W.D. Kingery, Physical Ceramics: Principles for Ceramic Science and Engineering, Har/Disk edn., Wiley, Hoboken, NJ, 1996
17. M. Qu, Y. Wu, V. Srinivasan, A. Gouldstone (2007) Observations of Nanoporous Foam Arising from Impact and Rapid Solidification of Molten Ni Droplets. Appl. Physics Lett 90(25):254101
18. A. Toramaru (1989) Vesiculation Process and Bubble Size Distributions in Ascending Magmas with Constant Velocities. J. Geophys. Res 94(B12):17523-17542
19. A. Toramaru (1995) Numerical Study of Nucleation and Growth of Bubbles in Viscous Magmas. J. Geophys. Res 100:1913-1931
20. G. Qian, T. Nakamura, C.C. Berndt, S. Leigh (1997) Tensile Toughness Test and High Temperature Fracture Analysis of Thermal Barrier Coatings. Acta Materialia 45(4):1767-1784
21. C.J. Li, J.L. Li (2004) Evaporated-Gas-Induced Splashing Model for Splat Formation During Plasma Spraying. Surf. Coat. Tech 184(1):13-23
22. L. Li, A. Gouldstone, and S. Sampath, Intrinsic Properties of Thermal Sprayed Single Splats on Substrate, Thermal Spray Solutions: Advances in Technology and Application (ITSC 2004) (Osaka, Japan), Electronic Proceedings, 2004
23. C.K. Shield, C.W. French, and E. Milde, The Effect of Adhesive Type on the Bond of NSM Tape to Concrete, ACI SP230: 7th International Symposium on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, American Concrete Institute, November 2005, p 355-372
24. R.S.J. Sparks (1978) The Dynamics of Bubble Formation and Growth in Magmas: A Review and Analysis. J. Volcanol. Geotherm. Res 3:1-37
25. H.M. Gonnermann, M. Manga (2007) The Fluid Mechanics inside a Volcano. Ann. Rev. Fl. Mech 39:321-356
26. C.J. Li, J.L. Li (2004) Transient Contact Pressure During Flattening of Thermal Spray Droplet and Its Effect on Splat Formation. J. Therm. Spray Technol 13:229-238
27. A.F. Mills, Basic Heat and Mass Transfer, 2nd ed. Series, Prentice Hall, Upper Saddler River, 1999
28. S. Sauerland, G. Lohofer, I. Egry (1993) Surface Tension Measurements on Levitated Liquid Metal Drops. J. Non-Crystalline solids 156-158:833-836
29. M. Chen, C. Yang, Z. Guo (2000) A Monte Carlo Simulation on Surface Tension of Liquid Nickel. Mat. Sci. Eng. A 292:203-206
30. C.A. Schuh (2006) Nanoindentation Studies of Materials. Materials Today 9(5):32-40
31. L. Li, X.Y. Wang, G. Wei, A. Vaidya, H. Zhang, S. Sampath (2004) Substrate Melting During Thermal Spray Splat Quenching. Thin Solid Films 468(1-2):113-119
32. B.C. Earls, Cavitation and Bubble Dynamics, Oxford University Press, Oxford, UK, 1995
33. N.H. March, Liquid Metals, Cambridge University Press, Cambridge, UK, 2005
34. M. Raessi, J. Mostaghimi, M. Bussmann (2005) Effect of Surface Roughness on Splat Shapes in the Plasma Spray Coating Process. Thin Solid Films 506-507:133-135
35. D.E. Wroblewski, R. Khare and M. Gevelber. Solidification Modeling of Plasma Sprayed TBC: Analysis of Remelt and Multiple Length Scales of Rough Substrates, J. Therm. Spray Technol,, 2002, Volume 11, Number 2, June 2002, pp. 266-275.
36. M. Fukumoto, Y. Huang, and M. Ohwatari, Flattening Mechanism in Thermal Sprayed Particle Impinging on a Flat Surface, Thermal Spray, Meeting the Challenge of the 21st Century, ASM International, 1998, p 401-407
37. P. Protopapas, N.A.D. Parlee (1976) Theory of Transport in Liquid Metals Iv Calculation of Interdiffusion Coefficients of Gases in Metals. High Temperature Science 8:141-165
38. T. Iida and R.I.L. Guthrie, The Physical Properties of Liquid Metals, Oxford University Press, Oxford, UK, 1993