Rapid solidification and microstructure development during plasma spray deposition

Journal of Thermal Spray Technology

Volumn 5, Issue 4, 1996, Pages 445-456

  Sampath, S ^a   Herman, H ^a  

^a Stony Brook University   (United States)

Author keywords

Electron microscopy; Metastable phases; Microstructure development; Rapid solidification; Texture

Indexed keywords

RAPID SOLIDIFICATION; SCANNING ELECTRON MICROSCOPY; SPRAYED COATINGS; TEXTURES; TRANSMISSION ELECTRON MICROSCOPY;

METASTABLE PHASES; MICROSTRUCTURE DEVELOPMENT;

PLASMA SPRAYING;

EID: 0030414282     PISSN: 10599630     EISSN: None     Source Type: Journal    
DOI: 10.1007/BF02645275     Document Type: Article

References (45)

1. S. Sampath and H. Herman, Plasma Spray Forming Metals, Intermetallics and Ceramics, J. Met., Vol 45 (No. 7), 1993, p 42-49
2. S. Safai and H. Herman, Plasma Sprayed Materials, Treat. Mater. Sci. Technol., Vol 20, 1981,p 183-214
3. M. Moss, Dispersion Hardening in Al-V by Plasma Jet Spray Quenching, Acta Metall., Vol 16, 1968, p 321-326
4. K.D. Krishnananda and R.W. Cahn, Properties of Plasma Sprayed Aluminum-Copper Alloys, Proc. 2nd Int. Conf. Rapid Quenching, Section I, B.C. Giessen and N.J. Grant, Ed., 1976, p 67-75
5. B.C. Giessen, M.N. Madhava, R.J. Murphy, R. Ray, and J. Surette, Sheet Production of an Amorphous Zr-Cu Alloy by Plasma Spray Quenching, Metall. Trans. A, Vol 8A, 1977, p 364-366
6. S.K. Das, E.M. Norin, and R.L. Bye, Ni-Mo-Cr-B Alloys: Corrosion Resistant Amorphous Hard Facing Coatings, Rapidly Solidified Metastable Materials, MRS Symp. Proc., Vol 28, B.H. Kear and M. Cohen, Ed., Materials Research Society, 1984, p 233-237
7. V. Panchanathan, C.L. Tsai, and S. Whang, Rapidly Solidified Amorphous and Crystalline Alloys, MRS Symp. Proc., Vol 8, B.H. kear, B.C. Giessen, and M. Cohen, Ed., Materials Research Society, 1982, p 137-141
8. S. Sampath, B. Katz, and H. Herman, Vacuum Plasma Sprayed Hard Coatings,Mém. Étud. Sci. Rev. Métall, Vol 88, May 1991, p 289-294
9. 3 Composite Coatings, Mat. Sci. Eng., Vol A108, 1989, p 87-95
10. H. Takigawa, M. Hirata, M. Koga, M. Itoh, and K.Takeda, Applications of Hard Coatings by Low Pressure Plasma Spray, Surf. Coat. Technol., Vol 39/40, 1989, p 127-134
11. S. Sampath and H. Herman, Microstructures of Vacuum Plasma Sprayed Coatings, Thermal Spray: Advances in Coating Technology, D.L. Houck, Ed., ASM International, 1988, p 1-7
12. S. Sampath, B. Gudmundsson, R. Tiwari, and H. Herman, Plasma Spray Consolidation of Ni-Al Intermetallics, Thermal Spray Research and Applications, T. Bernecki, Ed., ASM International, 1990, p 357-362
13. R. Tiwari, S. Sampath, and H. Herman, Plasma Spray Consolidation of High Temperature Composites, Mat. Sci. Eng., Vol A144, 1991, p 127-131
14. M.R. Jackson, J.R. Rairden, J.S. Smith, and R.W. Smith, Production of Metallurgical Structures by Rapid Solidification Plasma Deposition, J. Met., Vol 33 (No. 11), 1981, p 23-27
15. R.W. Smith, D.V. Rigney, J.S. Smith, and J.R. Rairden, Plasma Deposition Effects on Structures and Properties of RSPD Alloys, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, Ed., National Bureau of Standards, 1982, p 468-473
16. A.M. Johnson, J.S. Kelm, R.W. Smashey, D.V. Rigney, and T.G. Wakeman, Aircraft Engine Gas Turbine Component Fabrication Concepts using RSPD, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, Ed., National Bureau of Standards, 1982, p 650-661
17. T.L. Cheeks, M.E. Glicksman, M.R. Jackson, and E.L. Hall, Temperature Effects on Plasma Deposition of Ni-base Materials, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, Ed., 1982, p 118-123
18. A.M. Ritter and M.R. Jackson, Microstructural Characterization of RSPD Structures, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, Ed., National Bureau of Standards, 1982, p 118
19. E. Pfender, Fundamental Studies Associated with the Plasma Spray Process, Surf. Coat. Technol., Vol 34, 1988, p 1-14
20. A. Vardelle, M. Vardelle, R. McPherson, and P. Fauchais, Study of the Influence of Particle Temperature and Velocity Distribution within a Plasma Jet Coating Formation, Proc. 9th Int. Thermal Spray Conf., The Hague, Netherlands, 1980, p 155-161
21. J.M. Houben, "Relationship of the Adhesion of Plasma Sprayed Coatings to the Process Parameters: Size, Velocity and Heat Content of the Spray Particles," Ph.D. thesis. Technische Universiteit Eindhoven, Eindhoven, Netherlands, Dec 1988
22. R.C. Dykhuizen, Review of Impact and Solidification of Molten Thermal Spray Droplets, J. Therm. Spray Technol., Vol 3 (No. 4), 1994, p 351-361
23. M. Vardelle, A. Vardelle, A.C. Leger, P. Fauchais, and D. Gobin, Influence of Particle Parameters at Impact on Splat Formation and Solidification in Plasma Spraying Process, J. Therm. Spray Technol., Vol 4 (No. 1), 1994, p 50-58
24. C. Moreau, P. Gougeon, and M. Lamontagne, Influence of Substrate Preparation on the Flattening and Cooling of Plasma Sprayed Particles, J. Therm. Spray Technol., Vol 4 (No. 1), 1994, p 25-33
25. H. Herman, Plasma Sprayed Coatings, Sci. Am., Vol 256 (No. 9), Sept 1988, p 112-115
26. V. Wilms, Ph.D. thesis, State University of New York, Stony Brook, NY, 1978
27. C. Moreau, P. Cielo, M. Lamontagne, S. Dallaire, J.C. Krapez, and M. Vardelle, Temperature Evolution of Plasma Sprayed Niobium Particles Impacting on a Substrate, Surf. Coat. Technol., Vol 46, 1991, p 173-187
28. C. Moreau, P. Cielo, and M. Lamontagne, Influence of Coating Thickness on the Cooling Rates of Plasma Sprayed Particles Impinging on a Substrate, Surf. Coat. Technol., Vol 53, 1992, p 107-114
29. P. Duwez, Structure and Properties of Alloys Rapidly Quenched from the Liquid State, Trans. ASM, Vol 60, 1967, p 607-633
30. S. Sampath, "Rapid Solidification during Plasma Spraying," Ph.D. thesis, State University of New York, Stony Brook, NY, 1989
31. M. Cohen, B.H. Kear, and R. Mehrabian, Rapid Solidification Processing - An Outlook, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, B.H. Kear, and M. Cohen, Ed., Claitors, 1980, p 1-23
32. H. Matyja, B.C. Giessen, and N.J. Grant, The Effect of Cooling Rate on the Dendrite Arm Spacing of Splat Cooled Aluminum Alloys, J. Inst. Met., Vol 96, 1968, p 30-32
33. H. Jones, Experimental Methods in Rapid Quenching From the Melt, Treat. Mater. Sci. Technol., Vol 20, 1981, p 26-71
34. K. Murakami, T. Okamoto, Y. Miyamoto, and S. Nakazono, Rapid Solidification and Self-Annealing of Fe-C-Si Alloys by Low Pressure Plasma Spraying, Mat. Sci. Eng., Vol A117, 1989, p 207-214
35. R.C. Ruhl, Cooling Rates in Splat Cooling, Mat. Sci. Eng., Vol 1, 1968, p 313-320
36. S.C. Huang, R.P. Laforce, A.M. Ritter, and R.P. Goehner, Rapid Solidification Characteristics in Melt Spinning a Ni-base Superalloy, Metall. Trans. A, Vol 16A, 1985, p 1773
37. P. Predecki, A.W. Mullendore, and N.J. Grant, A Study of Splat Cooling Technique, Trans. Metall. Soc. AIME, Vol 233, 1965, p 1581-1586
38. D.R. Harbur, J.W. Anderson, and W.J. Maramen, Rapid Quenching Drop Smasher, Trans. Metall. Soc. AIME, Vol 233, 1965, p 1581-1586
39. T.R. Anantharaman and C. Surayanarayana, Rapidly Solidified Metals, Key Eng. Mater., Vol 17, 1987, p 80-86
40. P.H. Shingu and R. Ozaki, Solidification Rate in Rapid Conduction Cooling, Metall. Trans. A, Vol 6A, 1975, p 33-37
41. M. Cohen and R. Mehrabian, Some Fundamental Aspects of Rapid Solidification, Rapid Solidification Processing: Principles and Technologies, Vol III, R. Mehrabian, Ed., National Bureau of Standards, 1980, p 1-26
42. S. Safai and H. Herman, Microstructural Investigation of Plasma Sprayed Al-Coatings, Thin Solid Films, Vol 45, 1977, p 295-307
43. R.W. Cahn, Recrystallization, Grain Growth and Textures, American Society for Metals, 1966, p 99-100
44. C.S. Barret and T.B. Massalski, Structure of Metals, 3rd ed., Pergamon Press, 1980
45. E. Hornbergen, Phase-Structure and Micro-Structure in Rapidly Quenched Alloys, Rapidly Quenched Metals, S. Steeb and H. Warlimont, Ed., Elsevier, 1985, p 785-796