Wear phenomenon in the hard steel machining using ceramic tools

Tribology International

Volumn 41, Issue 8, 2008, Pages 802-812

  Grzesik, W ^a   Zalisz, Z ^a  

^a OPOLE UNIVERSITY OF TECHNOLOGY   (Poland)

Author keywords

Hard machining; Tool wear; Wear mechanisms

Indexed keywords

CERAMIC TOOLS; MACHINING; MICROSTRUCTURE; OPTICAL MICROSCOPY; SCANNING ELECTRON MICROSCOPY; WEAR OF MATERIALS;

CUTTING SPEED; HARD MACHINING; HARD STEEL; WEAR MECHANISMS;

STEEL;

EID: 43249093020     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2008.02.003     Document Type: Article

References (28)

1. Tönshoff H.K., Arendt C., and Ben Amor R. Cutting of hardened steel. CIRP Ann 49/2 (2000) 547-566
2. Byrne G., Dornfeld D., and Denkena B. Advancing cutting technology. CIRP Ann 52/2 (2003) 483-507
3. König W., Berktold A., and Koch K.F. Turning versus grinding-a comparison of surface integrity aspects and attainable accuracies. CIRP Ann 42/1 (1993) 39-43
4. Klocke F., Brinksmeier E., and Weinert K. Capability profile of hard cutting and grinding processes. CIRP Ann 54/2 (2005) 557-580
5. Chou K.Y., Evans J.Ch., and Barash M.M. Experimental investigation on CBN turning of hardened AISI 52100 steel. J Mat Proc Technol 124 (2002) 274-283
6. Chou Y.K., and Evans Ch.J. Tool wear mechanism in continuous cutting of hardened tool steels. Wear 212 (1997) 59-65
7. Chou Y.K. Hard turning of M50 steel with different microstructures in continuous and intermittent cutting. Wear 255 (2003) 1388-1394
8. Grzesik W., and Wanat T. Hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts. Int J Mach Tools Manuf 46 (2006) 1988-1995
9. Benga G.C., and Abrão A.M. Turning of hardened 100Cr6 bearing steel with ceramic and PCBN cutting tools. J Mat Proc Technol 143-144 (2003) 237-241
10. Hutchings I.M. Tribology. Friction and wear of engineering materials (1992), Edward Arnold, London
11. Brandt G. Flank and crater wear mechanisms of alumina-based cutting tools when machining steel. Wear 112 (1986) 39-56
12. Brandt G., and Mikus M. The formation of protective layers when machining steel with ceramic cutting tools. Wear 118 (1987) 99-112
13. Xiao H. Wear behaviour and wear mechanism of ceramic tools in machining hardened alloy steel. Wear 139 (1990) 439-451
14. Goh G.K.L., Lin L.C., Rahman M., and Lim S.C. Transition in wear mechanisms of alumina cutting tools. Wear 201 (1996) 199-208
15. Lo Casto S., Lo Valvo E., Lucchini E., Maschio S., and Ruisi V.F. Wear rates and wear mechanisms of alumina-based tools cutting steel at a low cutting speed. Wear 208 (1997) 67-72
16. Dutta A.K., Chattopadhyaya A.B., and Ray K.K. Progressive flank wear and machining performance of silver toughened alumina cutting tool inserts. Wear 261 (2006) 885-895
17. Stachowiak G.W., and Stachowiak G.B. Wear behaviour of ceramic cutting tools. Key Eng Mat 96 (1994) 137-164
18. Obikawa T., Matsumura T., Shirakashi T., and Usui E. Wear characteristic of alumina coated and alumina ceramic tools. J Mater Proc Technol 63 (1997) 211-216
19. Barry J., and Byrne G. Cutting tool wear in the machining of hardened steels. Part I: alumina/TiC cutting tool wear. Wear 247 (2001) 39-151
20. 3{single bond}TiC ceramic tools. Tribol Trans 36 (1993) 43-48
21. Kumar A.S., Durai A.R., and Sornakumar T. Wear behaviour of alumina based ceramic cutting tools on machining steels. Tribol Int 39 (2006) 191-197
22. New developments in hard part machining. 2002, 〈www.SandvikCoromant.com〉.
23. Grzesik W., and Wanat T. Comparative assessment of surface roughness produced by hard machining with mixed ceramic tools including 2D and 3D analysis. J Mater Proc Technol 169 (2005) 364-371
24. Grzesik W., and Wanat T. Hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts. Int J Mach Tools Manuf 46 (2006) 1988-1995
25. Wang J.Y., and Liu C.R. The effect of flank wear on the heat transfer, thermal damage and cutting mechanics in finish hard turning. CIRP Ann 48 1 (1999) 53-58
26. Liu Y.-R., Liu J.-J., Zhu B.-L., Luo Z.-B., and Miao H.-Z. The computer simulation of the temperature distribution on the surface of ceramic cutting tools. Wear 210 (1997) 39-44
27. Bothroyd G., and Knight W.A. Fundamentals of machining and machine tools (1989), Marcel Dekker, New York
28. Tool life testing with single-point turning tools, ISO Standard 3685:1993(E), 1993.