Cutting tool wear in the machining of hardened steels. Part I: Alumina/TiC cutting tool wear

Wear

Volumn 247, Issue 2, 2001, Pages 139-151

  Barry, J ^a   Byrne, G ^a  

^a UNIVERSITY COLLEGE DUBLIN   (Ireland)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINA; CARBIDE CUTTING TOOLS; INCLUSIONS; MACHINING; PLASTIC DEFORMATION; PRESSURE EFFECTS; SHEAR STRESS; STEEL; STRESS ANALYSIS; TITANIUM CARBIDE;

CONTACT PRESSURES; HARDENED STEELS; TOOL WEAR;

WEAR OF MATERIALS;

CUTTING TOOL; MACHINING; STEEL; TOOL WEAR;

EID: 0035241954     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0043-1648(00)00531-7     Document Type: Article

References (29)

1. H.K. Tönshoff, B. Karpuschewski, C. Borbe, Comparison of basic mechanisms in cutting and grinding of hardened steel, Prod. Eng. IV (2) (1997) 5-8.
2. H.K. Tönshoff, C.R. Arendt, R. Ben Amor, Cutting hardened steels, Ann. CIRP, 49 (2) (2000).
3. Y. Matsumoto, F. Hashimoto, G. Lahoti, Surface integrity generated by precision hard turning, Ann. CIRP 48 (1) (1999) 59-62.
4. Y.K. Chou, C.J. Evans, White layers and thermal modelling of hard turned surfaces, Int. J. Mach. Tools Manufac. 39 (1999) 1863-1881.
5. J. Barry, Machining Hardened Steels: Cutting Tool Wear, Acoustic Emission, Chip Formation and Surface Integrity, Ph.D. Thesis, University College Dublin, Dublin, 2000.
6. A.G. King, W.M. Wheildon, Ceramics in Machining Processes, Academic Press, New York, 1966.
7. J. Barry, G. Byrne, Cutting Tool Wear in the Machining of Hardened Steels, Part II: Cubic Boron Nitride Cutting Tool Wear, Wear 247 (2000) 152-160.
8. C.H. Kim, W.C. Smith, D.P.H. Hasselman, G.E. Kane, Evidence for dislocation-controlled crater wear of polycrystalline aluminium oxide cutting tools, J. Appl. Phys. 44 (11) (1973) 5175-5176.
9. 3 coated cutting tools during turning operations, Surf. Coat. Technol. 111 (1999) 191-198.
10. G. Brandt, M. Mikus, The formation of protective layers when machining steel with ceramic cutting tools, Wear 118 (1987) 99-112.
11. G.K.L. Goh, L.C. Lim, M. Rahman, S.C. Lim, Transitions in wear mechanisms of alumina cutting tools, Wear 201 (1996) 199-208.
12. G. Brandt, Flank and crater wear mechanisms of alumina-based cutting tools when machining steel, Wear 112 (1986) 39-56.
13. H.K. Tönshoff, S. Bartsch, Wear mechanisms of ceramic cutting tools, Ceram. Bull. 67 (6) (1988) 1020-1025.
14. G. Brandt, M. Mikus, An electron microprobe and cathodoluminescence study of chemical reactions between tool and workpiece when turning steel with alumina-based ceramics, Wear 115 (1987) 243-263.
15. I. Ham, N. Narutaki, Wear characteristics of ceramic tools, Trans. ASME J. Eng. Ind. 95 (1973) 951-959.
16. N. Narutaki, Improvement of the machinability of carbon steels due to small increase of sulfur content, in: Proceedings of the International Symposium on the Influence of Metallurgy on the Machinability of Steel, Tokyo, Japan, 1977, pp. 167-177.
17. N. Narutaki, A. Murakoshi, Effects of small quantity of inclusions in steels on the wear of ceramic tools, Bull. Jpn. Soc. Precis. Eng. 11 (3) (1977) 121-126.
18. N. Narutaki, Y Yamane, Tool wear and cutting temperature of CBN tools in machining of hardened steels, Ann. CIRP 28 (1) (1979) 23-28.
19. T. Ueda, M. Al Huda, K. Yamada, K. Nakayama, Temperature measurement of CBN tool in turning high hardness steel, Ann. CIRP 48 (1) (1999) 63-66.
20. 3), J. Am. Ceram. Soc. 77 (2) (1994) 385-397.
21. T. Obikawa, T. Matsumura, T. Shirakashi, E. Usui, Wear characteristics of alumina coated and alumina ceramic tools, J. Mater. Proc. Tech. 63 (1997) 211-216.
22. K. Ramanujachar, S.V. Subramanian, Micromechanisms of tool wear in machining free cutting steels, Wear 197 (1996) 45-55.
23. Y. Yamane, H. Usuki, B. Yan, N. Narutaki, The formation of a protective oxide layer in machining resulphurized free-cutting steels and cast irons, Wear 139 (1990) 195-208.
24. 3 - TiC ceramic tools, Tribol. Trans. 36 (1) (1983) 43-48.
25. A. Helle, On the Interaction Between Inclusions in Steel and the Cutting Tool During Machining, Ph.D. Thesis, Helsinki University of Technology, Acta Polytechnica Scandinavica, Chemical Technology Series, No. 228, 1995.
26. S. Kato, K. Yamaguchi, M. Yamada, Stress distribution at the interface between tool and chip in machining, Trans. ASME J. Eng. Ind. 94 (1972) 683-689.
27. P. Müller-Hummel, M. Lahres, Quantitative measurements of temperatures on diamond coated tools during machining, Diamond Relat. Mater. 4 (10) (1995) 1216-1221.
28. J. Barry, G. Byrne, The mechanisms of chip formation in machining hardened steels, Trans. ASME J. Manufac. Sci. Eng. 2000, in press.
29. M.A. Davies, S.E. Fick, C.J. Evans, Dynamic Measurement of Shear Band Formation in Precision Hard Turning, Liber Amicorum for Prof. Paul Vanherck, Katholieke Universiteit Leuven, 1996, pp. 215-224.