Experimental and numerical investigation of mechanical and thermal residual strains in adhesively bonded joints

Strain

Volumn 43, Issue 4, 2007, Pages 319-331

  Jumbo, F ^a   Ruiz, P D ^a   Yu, Y ^a   Swallowe, G M ^a   Ashcroft, I A ^a   Huntley, J M ^a  

^a LOUGHBOROUGH UNIVERSITY   (United Kingdom)

Author keywords

Double lap joint; Moir interferometry; Neutron diffraction; Residual stress; Thermal stress

Indexed keywords

ALUMINUM; CARBON FIBER REINFORCED PLASTICS; INTERFEROMETRY; NEUTRON DIFFRACTION; RESIDUAL STRESSES; STRAIN; THERMAL STRESS;

ADHESIVELY BONDED JOINTS; DOUBLE-LAP JOINT; MOIRE INTERFEROMETRY; RESIDUAL STRAINS;

ADHESIVE JOINTS;

EID: 35349000098     PISSN: 00392103     EISSN: 14751305     Source Type: Journal    
DOI: 10.1111/j.1475-1305.2007.00328.x     Document Type: Article

References (42)

1. Timoshenko, S. (1925) Analysis of bi-metal thermostats. J. Opt. Soc. Am. 11, 233-255.
2. Suhir, E. (1986) Stresses in bi-metal thermostats. J. Appl. Mech. Trans. ASME 53, 657-660.
3. Kuo, A.-Y. (1989) Thermal stresses at the edge of a bimetallic thermostat. J. Appl. Mech. Trans. ASME 56, 585-589.
4. Suhir, E. (1989) Interfacial stresses in bimetal thermostats. J. Appl. Mech. Trans. ASME 56, 595-600.
5. Weitsman, Y. (1980) Residual thermal stresses in a symmetric double lap joint. J. Thermal Stresses 13, 521-535.
6. Grant, P. and Lewington, J. A. (1987) Some important considerations in the design of composite joints in aerospace structures. Can. Aeronaut. Space J. 33, 91-98.
7. Adams, R. D., Coppendale, J., Mallick, V. and Al-Hamdan, H. (1992) The effect of temperature on the strength of adhesive joints. Int. J. Adhesion Adhesives 12, 185-190.
8. Kinloch, A. J., Thrusabanjong, E. and Williams, J. G. (1991) Fracture at bimaterial interfaces: The role of residual stresses. J. Mater. Sci. 26, 6260-6270.
9. Orsini, H. and Schmit, F. (1993) Influence of residual thermal stresses on the fracture behavior of hybrid bonded joints. J. Adhesion 43, 55-68.
10. Nairn, J. A. (2000) Energy release rate analysis for adhesive and laminate double cantilever beam specimens emphasizing the effect of residual stresses. Int. J. Adhesion Adhesives 20, 59-70.
11. Kawada, H. and Ikegami, K. (1992) Viscoelastic properties of resin for IC plastic packages and residual stress. JSME Int. J. 35, 152-158.
12. Ramani, K. and Zhao, W. (1997) The evolution of residual stresses in thermoplastic bonding to metals. Int. J. Adhesion Adhesives 17, 353-357.
13. Humfeld, G. R. and Dillard, D. A. (1998) Residual stress development in adhesive joints subjected to thermal cycling. J. Adhesion 65, 277-306.
14. Jumbo, F., Ashcroft, I. A., Crocombe, A. D. and Wahab, M. A. (2005) Modelling of hygro-thermal residual stresses in adhesively bonded joints. In: 9th Int. Conf. Sci. Technol. Adhesives. IOM Communications, Oxford.
15. Loh, W. K., Crocombe, A. D., Abdel Wahab, M. M. and Ashcroft, I. A. (2003) Modelling interfacial degradation using interfacial rupture elements. J. Adhesion 79, 1135-1160.
16. Yu, Y., Ashcroft, I. A. and Swallowe, G. (2006) An experimental investigation of residual stresses in an epoxy-steel laminate. Int. J. Adhesion Adhesives 26, 511-519.
17. Tandon, R. and Green, D. J. (1990) Residual stress determination using strain gage measurements. J. Am. Ceramic Soc. 73, 2628-2633.
18. Post, D., Wood, J. D., Han, B., Parks, V. J. and Gerstle, F. P. (1994) Thermal stresses in a bimaterial joint: An experimental analysis. J. Appl. Mech. 61, 192-198.
19. Kang, Y. L., Laermann, K. H. and Jia, Y. Q. (1995) Experimental analysis for bonded bimaterial beam under bending load. Measurement 15, 85-90.
20. Swallowe, G. M., Critchlow, G. W., Wimpory, R. C. and Pirling, T. (1999) Direct measurement of longitudinal strains and stresses within single lap shear adhesive joints using neutron diffraction. J. Adhesion 70 1-11.
21. Fitzpatrick, E. M. E. and Lodini, A. (2003) Analysis of residual stress by diffraction using neutron and synchrotron radiation. Measure. Sci. Technol. 14, 1739-1740.
22. Hutchings, M. T., Withers, P. J., Holden, T. M. and Lorentzen, T. (2005) Introduction to Characterization of Residual Stress by Neutron Diffraction. Taylor & Francis, London.
23. Monack, A. J. and Beeton, E. E. (1939) Analysis of strains and stress in glass. Glass Ind. 20 127-132.
24. Wang, W. C. and Hsu, J. S. (2004) Re-examination on thermal stresses of bonded structures. J. Strain Anal. Eng. Design 39, 261-270.
25. Oel, J. and Frechette, V. D. (1976) Stress distribution in multiphase systems: 1. Composites with planar interfaces. J. Am. Ceramic Soc. 50, 542-549.
26. Cytec. (1998) FM73 Toughened Epoxy Film. Available at: http://www.cytec.com; last accessed April 2004.
27. Molimard, J., Bounda, D. and Vautrin, A. (2006) Quantitative strain and slope evaluation on a double lap joint tensile test using ESPSI. In: Proc. SPIE Vol 6341 Speckle06: Speckles, From Grains to Flowers. Article 63412R. SPIE.
28. Martinez, A., Rodrguez-Vera, R., Rayas, J. A. and Puga, H. J. (2003) Fracture detection by grating moire and in-plane ESPI techniques. Opt. Lasers Eng. 39, 525-536.
29. Asundi, A. (1987) Deformation in adhesive joints using moire interferometry. Int. J. Adhesion Adhesives 7, 39-42.
30. Gascoigne, H. E. and Abdallah, M. G. (1990) Strain analysis of a bonded, dissimilar, composite material T-joint using moire interferometry. Opt. Lasers Eng. 13, 155-165.
31. Wang, Y. Y., Chiang, F. P., Barsoum, R. S. and Chou, S. T. (1993) Study of deformation field of interface crack in adhesive joint. Eng. Fracture Mech. 44, 175-184.
32. Lilleheden, L. (1994) Mechanical properties of adhesives in situ and in bulk. Int. J. Adhesion Adhesives 14, 31-37.
33. Tsai, M. Y. and Morton, J. (1994) 3-Dimensional deformations in a single-lap joint. J. Strain Anal. Eng. Design 29, 137-145.
34. Tsai, M. Y. and Morton, J. (1995) An experimental investigation of nonlinear deformations in single-lap joints. Mech. Mater. 20, 183-194.
35. Tsai, M. Y. and Morton, J. (1995) The effect of a spew fillet on adhesive stress distributions in laminated composite single-lap joints. Composite Struct. 32, 123-131.
36. Huntley, J. M. (2001) Automated analysis of speckle interferograms. In: Digital Speckle Pattern Interferometry and Related Techinques. (P. K. Rastogi, Ed.). John Wiley & Sons, Chichester, pp. 59-139.
37. Post, D., Han, B. and Ifju, P. (1994) High Sensitivity Moiré: Experimental Analysis for Mechanics and Materials. Springer-Verlag, New York.
38. Takeda, M., Ina, H. and Kobayashi, S. (1982) Fourier-transform method of fringe-pattern analysis for computer-based topography and interferometry. J. Opt. Soc. Am. 72, 156-160.
39. Buckland, J. R., Huntley, J. M. and Turner, S. R. E. (1995) Unwrapping noisy phase maps by use of a minimum-cost-matching algorithm. Appl. Opt. 34, 5100-5108.
40. Ruiz, P. D., Jumbo, F., Seaton, A., Huntley, J. M., Ashcroft, I. A. and Swallowe, G. M. (2006) Numerical and experimental investigation of 3-dimensional strains in adhesively bonded joints. J. Strain Anal. Eng. Design 41, 583-596.
41. Zimmermann, R., Klein, H. and Kling, A. (2006) Buckling and postbuckling of stringer stiffened fibre composite curved panels -tests and computations. Composite Struct. 73, 150-161.
42. Zimmermann, R. and Rolfes, R. (2006) POSICOSS - improved postbuckling simulation for design of fibre composite stiffened fuselage structures. Composite Struct. 73, 171-174.