Least-energy optimization of forced convection plate-fin heat sinks

InterSociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, ITHERM

Volumn 2002-January, Issue , 2002, Pages 792-799

  Iyengar, M ^a   Bar Cohen, A ^b  

^a University of Minnesota   (United States)

^b UNIVERSITY OF MARYLAND   (United States)

Author keywords

Assembly; Cooling; Entropy; Heat pumps; Heat sinks; Manufacturing; Minimization methods; Optimization methods; Performance analysis; Thermodynamics

Indexed keywords

ASSEMBLY; COOLING; ECONOMICS; ENERGY RESOURCES; ENTROPY; FINS (HEAT EXCHANGE); FORCED CONVECTION; HEAT SINKS; INVESTMENTS; LIFE CYCLE; MANUFACTURE; MINIMUM ENTROPY METHODS; THERMODYNAMICS;

ENTROPY GENERATION RATE; HEAT PUMPS; MATERIAL OPTIMIZATION; MINIMIZATION METHODS; OPTIMAL RESOURCE ALLOCATION; OPTIMIZATION METHOD; OPTIMIZATION METHODOLOGY; PERFORMANCE ANALYSIS;

HEAT CONVECTION;

EID: 0013458557     PISSN: 19363958     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1109/ITHERM.2002.1012535     Document Type: Conference Paper

References (23)

1. Bejan, A., 1995, Entropy Generation Minimization, CRC Press, New York.
2. Shuja, S. Z., Zubair, S. M., and Khan, M. S., 1999, Thermoeconomic Design and Analysis of Constant Cross-sectional Area Fins, Heat and Mass Transfer, Vol. 34, pp. 357-364.
3. Lin, W. W. and Lee, D. J., 2000, Second Law Analysis on a Flat Plate-fin Array under Crossflow, International Communications in Heat and Mass Transfer, Vol.27, no.2, pp. 179-190.
4. Culham, J. R., and Muzychka, Y. S., 2001, Optimization of Plate Fin Heat Sinks Using Entropy Generation Minimization, Trans. of IEEE-CPT, June, Vol. 24, No. 2pp. 159-165, ISSN 1521-3331.
5. Ogiso, K., 2001, Assessment of Overall Cooling Performance in Thermal Design of Electronics Based on Thermodynamics, Trans. of ASME J. of Heat Transfer, October, Vol. 123, pp. 999-10005.
6. st NHTC, HTD-Vol. 329, Volume 7, pp 63-71.
7. Zhao, Z. and Avedisian, C. T., 1997, Enhancing Forced Air Convection Heat Transfer from an Array of Parallel Plate Fins using a Heat Pipe, Int. J. Heat Mass Transfer, v40, No. 13, pp. 3135-3147.
8. Garner, S. D., and Toth, J. E., 1997, Heat Pipes: A Practical and Cost Effective Method for Maximizing Heat Sink Effectiveness, ASME Proc. of the Adv. Elec. Packaging, EEP v19-2, pp.1897-1902.
9. th ASME NHTC, NHTC'01, Anaheim, CA, NHTC2001-20019.
10. Sahin, A. Z., 1998, Second Law Analysis of Laminar Viscous Flow Through a Duct Subjected to Constant Wall Temperature, Trans. of the ASME J. Heat Transfer, v120, February, pp. 76-83.
11. Nag, P. K., and Mukherjee, P., 1987, Thermodynamic Optimization of Convective Heat Transfer Through a Duct with Constant Wall Temperature, International Journal of Heat Mass Transfer, Vol. 30, No. 2, pp. 401-405.
12. Ophardt, C. E., 2001, Course Notes: Chemistry 110, Chemistry and Issues in the Environment, Elmhurst College, Elmhurst, Illinois, USA.
13. Kakac, S., Shah, R. K., Aung, W., 1987, Handbook of Single-Phase Convective Heat Transfer, Second Edition, Wiley & Sons, New York, pp. 3-35, 3-42.
14. Kays, W. M., and London, A. L., 1984, Compact Heat Exchangers, Third Edition., pp. 108-112, McGraw Hill, Inc., NY.
15. Iyengar, M., and Bar-Cohen, A., 2001, Design for Manufacturability of SISE Parallel Plate Forced Convection Heat Sinks, Trans. of IEEE-CPT, June, Vol. 24, No. 2, pp. 150-158.
16. Bar-Cohen, A., Prstic, S., Yazawa, K, Iyengar, M., 2000, Design and Optimization of Forced Convection Heat Sinks for Sustainable Development, Proc. of the Euro Conference: New and Renewable Technologies for Sustainable Development, June, Madeira, Portugal.
17. LCA (Life Cycle Assessment) Committee Report, 1999, Summary of Inventory Data, Japan Aluminum Association, July.
18. Kraus, A. D., Aziz, A., Welty, J., 2001, Extended Surface Heat Transfer, John Wiley & Sons, New York.
19. Iyengar, M., and Bar-Cohen, A., 1998, Least-Material Optimization of Vertical Pin-Fin, Plate-Fin, and Triangular-Fin Heat Sinks in Natural Convective Heat Transfer, Proceedings of the ITHERM Conference, May'1998, Seattle, USA, pp. 295-302.
20. Bar-Cohen, A., Iyengar, M., and Kraus, A. D., 2001, Design of Optimum Plate-Fin Natural Convective Heat Sinks, accepted for publication to the ASME Journal of Electronic Packaging.
21. Chang, J. Y., Yu, C. W., and Webb, R. L., 2000, Identification of Minimum Air Flow Design for a Desktop Computer Using CFD Modeling, Proc. of the ITHERM Conference, Vol. 1, pp. 330-338.
22. th IEEE International Conference on Thermoelectrics, Dresden, Germany, August 26-29, pp. 563-566.
23. nd ASME NHTC - 'Second Law Aspects in Thermal Design', New York, HTD-v.33, August, pp. 19-26.