Variable Speed Generators

Variable Speed Generators

Volumn , Issue , 2005, Pages 1-538

  Boldea, Ion ^a  

^a POLITEHNICA UNIVERSITY OF TIMISOARA   (Romania)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 85076651037     PISSN: None     EISSN: None     Source Type: Book    
DOI: None     Document Type: Book

References (261)

1. T. Kuwabara, A. Shibuya, H. Feruta, E. Kita, and K. Mitsuhashi, Design and dynamic response characteristics of 400 MW adjustable speed pump storage unit OHKAWACHI station, IEEE Trans., EC-11, 2, 1996, pp. 376–384.
2. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 2001, p. 327.
3. I. Boldea, and S.A. Nasar, Electric Drives, CRC Press, Boca Raton, FL, 1998, chap. 14.
4. J. Tscherdanze, Theory of double-fed induction machine, Archiv fur electrotechnik, 15, 1925, pp. 257–263 (in German).
5. A. Leonhard, Asynchronous and synchronous running of the general doubly fed three phase machine, Archiv fur Electrotechnik, 30, 1936, pp. 483–502 (in German).
6. F.J. Bradly, A mathematical model for the doubly-fed wound rotor generator, IEEE Trans., PAS-103, 4, 1998, pp. 798–802.
7. M.S. Vicatos, and J.A. Tegopoulos, Steady state analysis of a doubly-fed induction generator under synchronous operation, IEEE Trans., EC-4, 3, 1989, pp. 495–501.
8. I. Cadirci, and M. Ermi, Double output induction generator operating at subsynchronous and supersynchronous speeds: steady state performance optimization and wind energy recovery, Proc. IEE, 139B, 5, 1992, pp. 429–442.
9. A. Masmoudi, A. Toumi, M.B.A. Kamoun, and M. Poloujadoff, Power flow analysis and efficiency optimization of a doubly fed synchronous machine, EMPS J., 21, 4, 1993, pp. 473–491.
10. D.G. Dorrel, Experimental behavior of unbalanced magnetic pull in three phase induction motors with excentric rotors and the relationship to teeth saturation, IEEE Trans., EC-14, 3, 1999, pp. 304–309.
11. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 2001, chap. 13.
12. M.S. Vicatos, and J.A. Tegopoulos, Transient state analysis of a doubly fed induction generator under three phase shortcircuit, IEEE Trans., EC-6, 1, 1991, pp. 62–68.
13. A. Masmoudi, and M.B.A. Kamoun, On the steady state stability comparison between voltage and current control of the doubly fed synchronous machine, In Proceedings of the IEEE/KTH Power Tech Conference, EMD, Stockholm, 1995, pp. 140–145.
14. M.G. Ioanides, Doubly fed induction machine state variable model and dynamic response, IEEE Trans., EC-6, 1, 1991, pp. 55–61.
15. D.P. Gonzaga, and Y. Burian Jr., Simulation of a three phase double-fed induction motor (DFIM): a range of stable operation, In Proceedings of EPE, Toronto, Canada, 1991.
16. I.F. Soran, The state and transient performance of double-fed asynchronous machine (DFAM), In Proceedings of EPE, Firenze, Italy, 1991, pp. 2-395–2-399.
17. I. Cadirci, and M. Ermis, Performance evaluation of wind driven DOIG using a hybrid model, IEEE Trans., EC-13, 2, 1998, pp. 148–154.
18. E. Akpinar, and P. Pillay, Modeling and performance of slip energy recovery induction motor drives, IEEE Trans., EC-5, 1, 1990, pp. 203–210.
19. M. Yamamoto, and O. Motoyoshi, Active and reactive power control for doubly-fed wound rotor induction generator, IEEE Trans., PE-6, 4, 1991, pp. 624–629.
20. P. Bauer, S.W.H. De Hoan, and M.R. Dubois, Wind energy and off shore windparks: state of the art and trends, In Proceedings of EPE-PEMC, Dubrovnik and Cavtat, Croatia, 2002, pp. 1–15.
21. R. Rena, J.C. Clare, and G.M. Asher, Doubly-fed induction generator using back to back PWM converters and its application to variable-speed wind-energy generation, Proc. IEE, PA-143, 3, 1996, pp. 231–241.
22. I. Serban, F. Blaabjerg, I. Boldea, and Z. Chen, A study of the double-fed wind power generator under power system faults, Record of EPE-2003, Toulouse, France.
23. S. Muller, M. Deicke, and R.W. De Doncker, Adjustable speed generators for wind turbines based on doubly fed machines and 4-quadrant IGBT converters linked to the rotor, Record of IEEE-IAS-2000, Annual Meeting, Roma, Italy, 2000, pp. 2249–2254.
24. I. Boldea, and S.A. Nasar, Electric Drives, CRC Press, Boca Raton, FL, 1998.
25. R. Datta, and V.T. Ranganathan, Direct power control of grid-connected wound rotor induction machine without rotor position sensors, IEEE Trans., PE-16, 3, 2001, pp. 390–399.
26. E. Bogalecka, and Z. Kvzeminski, Sensorless control of double fed machine for wind power generators, In Proceedings of EPE-PEMC, Dubrovnik and Cavtat, 2002.
27. J. Bendl, M. Chomat, and L. Schreier, Independent control of positive and negative sequence current components in doubly fed machine, Record of ICEM, Bruges, Belgium, 2002.
28. R. Datta, and V.T. Ranganathan, A simple position-sensorless algorithm for rotor-side field-oriented-control of wound-rotor induction machine, IEEE Trans., IE-48, 4, 2001, pp. 786–793.
29. L. Morel, H. Goofgroid, H. Mirzgaian, and J.M. Kauffmann, Double-fed induction machine: converter optimization and field orientated control without position sensor, Proc. IEE, EPA-145, 4, 1998, pp. 360–368.
30. U. Radel, D. Navarro, G. Berger, and S. Berg, Sensorless field-oriented control of a slip ring induction generator for a 2.5 MW wind power plant from Mordex Energy Gmbh, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P7.
31. R. Pena, J.C. Clare, and G.M. Asher, A doubly fed induction generator using back to back PWM converters supplying an isolated load from a variable speed turbine, Proc. IEE, EPA-143, 5, 1996, pp. 380–387.
32. T. Kawabara, A. Shibuya, and H. Furata, Design and dynamic response characteristics of 400 MW adjustable speed pump storage unit for Ohkawachi Power Station, IEEE Trans., EC-11, 2, 1996, pp. 376–384.
33. B. Singh, K. Al-Haddad, and A. Chandra, A review of active filters for power quality improvements, IEEE Trans., IE-46, 1, 1999, pp. 960–971.
34. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
35. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
36. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
37. L. Zhang, C. Watthanasarn, and W. Shepherd, Application of a matrix converter for the power control of a variable-speed wind-turbine driving, Record of IEEE-IAS 2000 Meeting, 2000, pp. 906–911.
38. V. Akhmatan, Modelling of variable speed wind turbines with double-fed induction generators in short-term stability investigations, In Proceedings of Third Workshop on Transmission Networks for Offshore Wind Farms, Stockholm, Sweden, April 11–12, 2002, pp. 1–23.
39. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 1998.
40. E. Levi, Poliphase Motors — A Direct Approach to Their Design, Wiley Interscience, New York, 1985.
41. K. Vogt, Electrical Machines: Design of Rotary Machines, 4th ed., VEB Verlag, Berlin, 1988 (in German).
42. D.G. Dorrel, Experimental behavior of unbalanced magnetic pull in 3-phase induction motors with eccentric rotors and the relationship with teeth saturation, IEEE Trans., EC-14, 3, 1999, pp. 304–309.
43. Institute of Electrical and Electronics Engineers (IEEE), IEEE Standard Procedure for Polyphase Induction Motors and Generators, IEEE standard 112-1996, IEEE Press, New York, 1996.
44. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 2001.
45. E.D. Basset, and F.M. Potter, Capacitive excitation of induction generators, Electrical Eng., 54, 1935, pp. 540–545.
46. S.S. Murthy, O.P. Malik, and A.K. Tandon, Analysis of self-excited induction generators, Proc. IEE, 129, Part. C, 7, 1982, pp. 260–265.
47. L. Ouazone, and G. McPherson, Analysis of the isolated induction generator, IEEE Trans., IAS-102, 8, 1983, pp. 2793–2798.
48. L. Shrider, B. Singh, and C.S. Tha, Towards improvements in the characteristics of selfexcited induction generators, IEEE Trans., EC-8, 1, 1993, pp. 40–46.
49. S.P. Singh, B. Singh, and M.P. Jain, A new technique for the analysis of selfexcited induction generator, EMPS J., 23, 6, 1995, pp. 647–656.
50. T.F. Chan, and L.L. Lai, Steady state analysis and performance of a stand alone three phase induction generator with asymmetrical connected load impedances and excitation capacitances, IEEE Trans., EC-16, 4, 2001, pp. 327–333.
51. N. Ammasaigounden, M. Subbiah, and M.R. Krishnamurthy, Wind driven self-excited pole changing induction generator, Proc. IEE, 133B, 6, 1986, pp. 315–321.
52. T.F. Chan, Analysis of self-excited induction generators using an iterative method, IEEE Trans., EC-10, 3, 1995, pp. 502–507.
53. K.S. Sandhu, and S.K. Jain, Operational aspects of self-excited induction generator using a new model, EMPS J., 27, 2, 1999, pp. 169–180.
54. S. Rajakaruna, and R. Bonert, A technique for the steady state analysis of a selfexcited induction generator with variable speed, IEEE Trans., EC-8, 4, 1993, pp. 757–761.
55. L. Shridha, B. Singh, C.S. Tha, B.P. Singh, and S.S. Murthy, Selection of capacitors for the selfreg-ulated short shunt self-excited induction generators, IEEE Trans., EC-10, 1, 1995, pp. 10–16.
56. E. Suarez, and G. Bortolotto, Voltage-frequency control of a self-excited induction generator, IEEE Trans., EC-14, 3, 1999, pp. 394–401.
57. P. Chidambaram, K. Achutha, M. Subbiah, and M.R. Krishnamurthy, A new pole changing winding using star/star delta switching, Proc. IEE, B-EPA-130, 2, 1983, pp. 130–136.
58. R. Parimelalasan, M. Subbiah, and M.R. Krishnamurthy, Design of dual speed single-winding induction motors — a unified approach, Record IEEE-IAS-1976 Annual Meeting, paper 398, pp. 1071–1079.
59. N. Ammasaigounden, M. Subbiah, and M.R. Krishnamurthy, Wind-driven selfexcited pole-changing induction generators, Proc. IEE, 133 part B, 5, 1986, pp. 315–322.
60. A.M. Bahrani, Analysis of selfexcited induction generators under unbalanced conditions, EMPS J., 24, 2, 1996, pp. 117–129.
61. A.W. Ghorashi, S.S. Murthy, B.P. Singh, and B. Singh, Analysis of winddriven grid connected induction generators under unbalanced conditions, IEEE Trans., EC-9, 2, 1994, pp. 217–223.
62. T.F. Chan, and L.L. Lai, A novel single-phase self-regulated self-excited induction generator using three phase machine, IEEE Trans., EC-16, 2, 2001, pp. 204–208.
63. T.F. Chan, and L.L. Lai, Single-phase operation of a three-phase induction generator with Smith connection, IEEE Trans., EC-17, 1, 2002, pp. 47–54.
64. T. Fukami, Y. Kaburaki, S. Kawahara, and T. Miyamoto, Performance analysis of self-regulated and self-excited single phase induction machine using a three phase machine, IEEE Trans., EC-14, 3, 1999, pp. 622–627.
65. Y.H.A. Rahim, I.I. Alolah, and R.I. Al-Mudaiheem, Performance of single phase induction generators, IEEE Trans., EC-8, 3, 1993, pp. 389–395.
66. M.H. Salama, and P.G. Holmes, Transients and steady-state load performance of stand-alone self-excited induction generator, Proc. IEE, EPA-143, 1, 1996, pp. 50–58.
67. O. Ojo, Performance of self-excited single-phase induction generators with shunt, short-shunt and long-shunt excitation connections, IEEE Trans., EC-14, 1, 1999, pp. 93–100.
68. L. Wang, and J.Y. Su, Dynamic performace of an isolated self-excited induction generator under various loading conditions, IEEE Trans., EC-14, 1, 1999, pp. 93–100.
69. B. Singh, L. Shridar, and C.B. Iha, Transient analysis of selfexcited generator supplying dynamic load, EMPS J., 27, 9, 1999, pp. 941–954.
70. A.H. Al-Bahrani, and N.H. Malik, Voltage control of parallel operated self-excited induction generators, IEEE Trans., EC-8, 2, 1993, pp. 236–242.
71. C.H. Lee, and L. Wang, A novel analysis of parallel operated self-excited induction generators, IEEE Trans., EC-14, 2, 1998, pp. 117–123.
72. L. Mihet-Popa, F. Blaabjerg, and I. Boldea, Wind turbine generator modeling and simulation where rotational speed is the controlled variable, IEEE Trans., IA-40, 1, 2004, pp. 8–13.
73. T. Thiringer, Grid friendly connected of constant speed wind turbines using external resistors, IEEE Trans., EC-17, 4, 2002, pp. 537–542.
74. A. Larsson, Guidelines for grid connection of wind turbines, Record of 15th International Conference on Electricity Distribution, Nice, France, June 1–4, 1999.
75. S.A. Papathanassiou, and M.P Papadopoulos, Mechanical stresses in fixed speed wind turbines due to network disturbances, IEEE Trans., EC-16, 4, 2001, pp. 361–367.
76. P. Vas, K.E. Hallenius, and J.E. Brown, Cross-saturation in smooth airgap electrical machines, IEEE Trans., EC-1, 1, 1986, pp. 103–112.
77. I. Boldea, and S.A. Nasar, Unified treatment of core loss and saturation in the DQ models of electrical machines, Proc. IEE, 134B, 6, 1987, pp. 355–363.
78. A. Larsson, Flicker emission of wind turbines during continuous operation, IEEE Trans., EC-17, 1, 2002, pp. 114–118.
79. A. Larsson, Flicker emission of wind turbines caused by switching operations, IEEE Trans., EC-17, 1, 2002, pp. 119–123.
80. P.W. Wheeler, J. Rodriguez, J.C. Clare, L. Empringham, and A. Wheinstein, Matrix converters: a technology review, IEEE Trans., IE-49, 2, 2002, pp. 276–288.
81. C. Klumpner, P. Nielsen, I. Boldea, and F. Blaaabjerg, A new matrix converter motor (MCM) for industry applications, IEEE Trans., IE-49, 2, 2002, pp. 325–335.
82. J. Rodriguez, J.B. Lai, and F.Z. Peng, Multilevel inverters: a survey of topologies, control and applications, IEEE Trans., IE-49, 4, 2002, pp. 724–734.
83. I. Boldea, and S.A. Nasar, Electric Drives, CRC Press, Boca Raton, FL, 1998.
84. D.G. Luenberger, An introduction to observers, IEEE Trans., AC-16, 6, 1971, pp. 596–602.
85. E.A. Misawa, and J.K. Hedrick, Nonlinear observers — a state of the art survey, Trans. ASME J. Dyn. Syst., Meas. Control, 111, September, 1989, pp. 344–352.
86. R.G. Brown, and P.Y.C. Huang, Introduction to Random Signals and Applied Kalman Filtering, 3rd ed., John Wiley & Sons, New York, 1997.
87. C. Lascu, Direct Torque Control of Sensorless Induction Machine Drives, Ph.D. thesis, University of Politehnica Timisoara, Romania, 2002.
88. C. Lascu, I. Boldea, and F. Blaabjerg, A modified direct torque control for induction motor sensorless drive, IEEE Trans., IA-36, 1, 2000, pp. 130–137.
89. I. Boldea, Direct torque and flux control of a.c. drives: a review, Record of EPE-PEMC-2000, Kosice, Slovakia, 2000, pp. 88–97.
90. J. Holtz, Pulse width modulation for electronic power conversion, in Power Electronics and Variable Speed Drives, B. Bose, Ed., IEEE Press, Washington, 1997, chap. 4.
91. R. Teodorescu, F. Blaabjerg, and F. Iov, Control strategy for small standalone wind turbines, Record of PCIM 2003 Power Quality, Nurnberg, Germany, May 20–22, 2003, pp. 201–206.
92. E.A.V. Coelho, P. Cortez, and P.F. Garcia, Small signal stability for parallel connected inverters in standalone a.c. supply systems, IEEE Trans., IA-38, 2, 2002, pp. 533–542.
93. G. Saccomando, J. Svensson, and A. Sannino, Improving voltage disturbance rejection for variable speed wind turbines, IEEE Trans., EC-17, 3, 2002, pp. 422–428.
94. D.W. Novotny, D.J. Gritter, and G.H. Studmann, Self excitation in inverter driven induction machines, IEEE Trans., PAS-96, 4, 1977, pp. 1117–1125.
95. M.S. Miranda, R.O.C. Lyra, and S.R. Silva, An alternative isolated wind electric pumping system using induction machines, IEEE Trans., EC-14, 4, 1999, pp. 1611–1616.
96. T.L. Maguire, and A.M. Gole, Apparatus for supplying an isolated d.c. load from a variable speed selfexcited induction generator, IEEE Trans., EC-8, 3, 1993, pp. 468–475.
97. H. Huang, and L. Chang, A new d.c. link boost scheme for IGBT inverters for wind energy extraction, in Proceedings of the Electrical and Computer Engineering 2000 Canadian Conference, Vol. 1, Halifax, 2000, pp. 540–544.
98. O. Ojo, and I.E Davidson, PWM VSI inverter assisted standalone dual stator winding generator, Record of IEEE–IAS 1999 Annual Meeting, 1999.
99. A. Munoz-Garcia, and T.A. Lipo, Dual stator winding induction motor drive, Record of IEEE–IAS 1998 Annual Meeting, Vol. I, pp. 601–608.
100. M.N. Marwali, and A. Keyhani, Control of distributed generation systems, parts I + II, IEEE Trans., PE-19, 6, 2004, pp. 1541–1561.
101. I.G. Kassakian, H.-C. Wolf, J.M. Miller, and C.J. Hurton, Automotive electrical systems circa 2005, IEEE Spectrum, 33, 8, August, 1996.
102. G. Hennenberger, and J.A. Viorel, Variable Reluctance Electrical Machine, Shaker Verlag, Aachen, 2001.
103. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 2001.
104. V. Ostovic, J.M. Miller, V. Garg, R.D. Schultz, and S. Swales, A magnetic equivalent circuit based performance computation of a Lundell alternator, Record of IEEE–IAS 1998, Annual Meeting, Vol. 1, 1998, pp. 335–340.
105. V. Ostovic, Dynamics of a Saturated Electric Machine, Springer-Verlag, New York, 1989.
106. R. Block, and G. Hennenberger, Numerical calculation and simulation of a claw-pole alternator, Record of ICEM–1992, Vol. 1, 1992, pp. 127–131.
107. G. Hennenberger, S. Küppers, and I. Ramesohl, Sensorless permanent-magnet brushless D.C. and synchronous motor drives, Electromotion, 3, 4, 1996, pp. 165–177.
108. R. Wang, and N.A. Demerdash, Computation of load performance and other parameters of extra-high-speed modified Lundell alternator from 3D–FE magnetic field solutions, IEEE Trans., EC-7, 2, 1992, pp. 342–361.
109. S. Küppers, Numerical Method for the Study and Design of A.C. Claw-Pole Generator, Ph.D. thesis, RWTH, Aachen, 1996 (in German).
110. K. Xamazaki, Torque and efficiency calculation of an interior PM motor considering harmonic iron losses of both stator and rotor, IEEE Trans., MAG 39, 3, pp. 1460–1463.
111. A. Munoz-Garcia, and D.W. Novotny, Utilization of third harmonic-induced-voltages in PM generators, Record of IEEE–IAS 1996 Annual Meeting, Vol. 1, 1996, pp. 525–532.
112. A. Mailat, D. Stoia, and D. Ilea, Vehicle alternator with improved performance, Record of Electromotion–2001, Bologna, Vol. 2, 2001, pp. 511–514.
113. F. Liang, J. Miller, and X. Xu, A vehicle electric power generation system with improved power and efficiency, IEEE Trans., IA-35, 6, pp. 1341–1346.
114. C. Kahler, and G. Henneberger, Calculation of the mechanical and acoustic behavior of a claw pole alternator in a double and single star connection, Records of Electromotion–2001 Symposium, Bologna, Vol. 2, pp. 553–558.
115. T. Teratani, K. Kurarnoki, H. Nakao, T. Tachibana, K. Yagi, and S. Abae, Development of Toyota mild hybrid systems (THS-M) with 42 V power net, Records of IEEE–IEMDC–2003, Madison, WI, 2003, pp. 3–10.
116. I. Boldea, and S.N. Nasar, Electric Drives, CRC Press, Boca Raton, FL, 1998.
117. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
118. C. Lascu, I. Boldea, and F. Blaabjerg, Very low speed sensorless control of induction motor drives without signal injection, Record of IEEE–IEMDC–2003 Conference, Madison, WI, 2003, 1395–1401.
119. D.J. Perreault, and V. Caliskan, Automotive power generation and control, IEEE Trans., PE-19, 3, 2004, pp. 618–630.
120. S.A. Nasar, and L.E. Unnewher, Electrical Vehicle Technology, John Wiley & Sons, New York, 1981.
121. I. Husain, Electric and Hybrid Vehicles, CRC Press, Boca Raton, FL, 2003.
122. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
123. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
124. E. Spijker, A. Saibertz, R. Busch, D. Kak, and D. Pelergus, An ISG with dual voltage power net stretching the technology boundaries for higher fuel economy, Record of EVS-18 World Congress 2001, Berlin, Germany, 2001.
125. S. Chen, B. Lequesne, R.R. Henry, Y. Xuo, and J. Ronning, Design and testing of belt-driven induction starter-generator, IEEE Trans., IA-38, 6, 2002, pp. 1525–1532.
126. T. Teratani, K. Kuramochi, H. Nakao, T. Tachibana, K. Yagi, and S. Abou, Development of Toyota mild hybrid system (THS-M) with 42V PowerNet, Record of IEEE–IEMDC-2003, Madison, WI, 2003, pp. 3–10.
127. I. Boldea, L. Tutelea, and C.I. Pitic, PM-assisted reluctance synchronous motor-generator (PM-RSM) for mild hybrid vehicles, Record of OPTIM-2002, vol. 2, Poiana Brasov, Romania, 2002, pp. 383–388.
128. A. Vagati, A. Fratta, P. Cugliehmi, G. Franchi, and F. Villata, Comparison of AC motor based drives for electric vehicle, Record of PCIM-1999, Intelligent Motion Conference, Nurnberg, 1999, pp. 173–181.
129. A. Lange, W.R. Canders, F. Laube, and H. Mosebach, Comparison of different drive systems for a 75 KW electrical vehicle drive, Record of ICEM-2000, vol. 2, Espoo Finland, 2000, pp. 1308–1312.
130. S. Barsali, M. Ceraolo, and A. Possenti, Tehniques to control the electricity generation in a series hybrid electrical vehicle, IEEE Trans., EC-17, 2, 2002, pp. 260–266.
131. D. Rand, R. Wood, and R.M. Dell, Batteries for Electric Vehicle, John Wiley & Sons, New York, 1998.
132. I. Boldea, and S.A. Nasar, Induction Machine Handbook, CRC Press, Boca Raton, FL, 2001.
133. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
134. P.J. McCleer, J.M. Miller, A.R. Gale, M.W. Degner, and F. Leonardi, Nonlinear model and momentary performance capability of a cage rotor induction machine used as an automotive combined starter-alternator, IEEE Trans., IA-37, 3, 2001, pp. 840–846.
135. F. Briz, M.W. Degner, A. Diez, and R.D. Lorenz, Static and dynamic behavior of saturation-induced saliences and their effect on carrier signal-based sensorless AC drives, IEEE Trans., IA-38, 3, 2002, pp. 670–678.
136. C. Lascu, I. Boldea, and F. Blaabjerg, Very low speed sensorless variable structure control of induction machine, Record of IEEE–IEMDC-2003 Conference, Madison, WI, 2003.
137. W.L. Soong, G.B. Kliman, N.R. Johnson, R. White, and J. Miller, Novel high speed induction motor for a commercial centrifugal compressor, Record of IEEE–IAS-1999 Annual Meeting, vol. 1, 1999, pp. 494–501.
138. L. Küng, K. Reichert, and A. Vezzini, Winding arrangement for multipolar squirrel cage induction machine with low leakage inductance, Record of ICEM-1998, Instanbul, vol. 1, 1998, pp. 353–358.
139. M. Osana, and T.A. Lipo, A new inverter control scheme for induction motor drives requiring wide speed range, Record of IEEE–IAS-1995 Annual Meeting, vol. 1, 1995, pp. 350–355.
140. C. Zang, I. Yang, X. Chen, and Y. Gue, A new design principle for pole changing winding — the three equation principle, EMPS J., 22, 2, 1994, pp. 1859–1865.
141. D. Casadei, C. Rossi, G. Serra, and A. Tani, Performance analysis of an electric vehicle driven by SFVC induction motor drive, Record of Electromotion-2001, Bologna, vol. 1, 2001, pp. 141–146.
142. L. Tutelea, E. Ritchie, and I. Boldea, Induction machine design with and without mechanical transmission for electrical vehicle drives, Record of Electromotion-2001, Bologna, vol. 1, 2001, pp. 275–280.
143. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
144. E.C. Lovelace, T.M. Jahns, J.L. Kirtley Jr., and J.H. Lang, An interior PM starter/alternator for automotive applications, Record of ICEM-1998, Istanbul, vol. 3, 1998, pp. 1802–1808.
145. A. Vagati, A. Fratta, P. Gugliehmi, G. Franchi, and F. Villata, Comparisons of AC motor based drives for electric vehicle application, Record of PCIM-1999, Europe Vol., Intelligent Motion, 1999, pp. 173–181.
146. E.C. Lovelace, T.M. Jahns, T.A. Keim, and J.H. Lang, Mechanical design considerations for conventionally-laminated high-speed interior PM synchronous machine rotors, Record of IEEE–IEMDC-2001, 2001, pp. 163–169.
147. I. Boldea, Reluctance Synchronous Machines and Drives, Oxford University Press, Oxford, 1996.
148. W.L. Soong, D.A. Staton, and T.J.E. Miller, Design of new axially-laminated interior permanent magnet motor, Record of IEE–IAS, 1993 Annual Meeting, 1993, pp. 27–36.
149. Y. Honda, Rotor design optimization of a multilayer interior PM synchronous motor, Proc. IEE, EPA-145, 2, 1998, pp. 119–124.
150. A. Vagati, A. Canova, M. Chiampi, M. Pastorelli, and M. Repeto, Design refinement of synchronous reluctance motors through finite element analysis, IEEE Trans., IA-36, 4, 2000, pp. 1094–1102.
151. I. Boldea, L. Tutelea, and C.I. Pitic, PM assisted reluctance synchronous motor/generator (PM-RSM) for mild hybrid vehicle, Record of OPTIM-2002, Poiana Brasov, Romania, 2002, pp. 383–388.
152. P. Guglielmi, G.M. Pellegrino, G. Griffero, S. Mieddu, G. Girando, and A. Vagati, Conversion concept for advanced autonomy and reliability scooter, Record of IEEE–IECON, 2003, pp. 2883–2888.
153. E.C. Lovelace, T. Jahns, T. Keim, J. Lang, D. Wentzloff, F. Leonardi, J. Miller, and P. McCleer, Design and experimental verification of a direct-drive interior PM synchronous machine using a saturable parameter model, Record of IEEE–IAS-2002 Annual Meeting, 2002.
154. D.H. Kim, I.H. Park, J.H. Lee, and C.E. Kim, Optimal shape design of iron core to reduce cogging torque of IPM motor, IEEE Trans., MAG-39, 3, 2003, pp. 1456–1459.
155. G.H. Kang, J.P. Hong, and G.T. Kim, Analysis of cogging torque in interior permanent magnet motor by analytical method, J. KIEE, 11-B, 1, 2001, pp. 1–8.
156. K. Yamazaki, Torque and efficiency calculation of an interior permanent magnet motor considering harmonic iron losses of both stator and rotor, IEEE Trans., MAG-39, 3, 2003, pp. 1460–1463.
157. T.A. Jahns, Component rating requirements for vehicle constant power operation of IPM synchronous machine drives, Record of IEEE–IAS-2000, Annual Meeting, Rome, 2000, pp. 1697–1704.
158. R.F. Schiferl, and T.A. Lipo, Power capabilities of salient pole permanent magnet synchronous motor variable speed applications, IEEE Trans., IA-26, 1, 1990, pp. 115–123.
159. B.A. Welchko, T.A. Jahns, W.C. Long, and J.M. Nagashima, IPM synchronous machine drive response to symmetrical and asymmetrical shortcircuit faults, IEEE Trans., EC-28, 2, 2003, pp. 291–298.
160. T.M. Jahns, Uncontrolled generator operation of interior PM synchronous machine following high-speed inverter shutdown, Record of IEEE–IAS, 1998.
161. W.L. Soong, N. Ertugrul, E.C. Lovelace, and T.M. Jahns, Investigation of interior permanent magnet off-set coupled automotive integrated starter/alternator, Record of IEEE–IAS-2001, Annual Meeting, 2001.
162. I. Boldea, L. Ianosi, and F. Blaabjerg, A modified direct torque control (DTC) of reluctance synchronous motor sensorless drive, EMPS J., 28, 1, 2000, pp. 115–128.
163. G.D. Andreescu, Robust sliding mode based observer for sensorless control of PMSM drives, Record of EPE–PEMC-1998, vol. 6, Prague, 1998, pp. 172–177
164. M. Patel, T. O’Meara, J. Nagashinia, and R.D. Lorenz, Encoderless IPM drive system for EH-HEV propulsion applications, Record of EPE-2001, Graz, Austria, 2001.
165. M.M. Degner, and R.D. Lorenz, Wide band width flux position and velocity estimation in AC machines at any speed (including zero) using high multiple saliences, Record of EPE-1997, Trondheim, Norway, 1997, pp. 1530–1535.
166. M.M. Corely, and R.D. Lorenz, Rotor position and velocity estimation for a permanent magnet synchronous machine at standstill and high speed, IEEE Trans., IA-34, 4, 1998, pp. 784–789.
167. T. Aihara, A. Tobu, T. Yanase, A. Mashimoto, and K. Endo, Sensorless torque control of salient pole synchronous motor at zero speed operation, IEEE Trans., PE-14, 1, 1999, pp. 202–208.
168. M. Schroedl, Sensorless control of AC machines at low speed and standstill based on the INFORM method, Record of IEEE–IAS-1996 Meeting, vol. 1, 1996, pp. 270–277.
169. A. Consoli, G. Scarcella, and A. Testa, Sensorless control of PM synchronous motors at zero speed, Record of IEEE–IAS-1999 Annual Meeting, vol. 2, 1999, pp. 1033–1040.
170. T. Noguchi, K. Yamada, S. Kondo, and I. Takahashi, Initial rotor position estimation of sensorless PM synchronous motor with no sensitivity to armature resistance, IEEE Trans., IE-45, 1, 1998, pp. 118–125.
171. D.W. Chung, J.K. Kang, and S.K. Sul, Initial rotor position detection of PMSM at standstill without rotational transducer, Record of IEEE–IEMDC-1999, 1999, pp. 785–787.
172. J.I. Ha, K. Ide, T. Sawa, and S.K. Sul, Sensorless position control and initial position estimation of an interior permanent magnet motor, Record of IEEE–IAS-2001, 2001, pp. 2607–2613.
173. H. Kim, K.K. Huh, H. Harke, J. Wai, R.D. Lorenz, and T. Jahns, Initial rotor position estimation for an integrated starter alternator IPM synchronous machine, Record of EPE-2003, Toulouse, France, 2003.
174. Y. Yeong, R.D. Lorenz, T.M. Jahns, and S.K. Sul, Initial rotor position estimation of interior PMSM using carrier-frequency injection methods, Record of IEEE–IEMDC-2003, vol. 2, 2001, pp. 1218–1223.
175. M. Linke, R. Kennel, and J. Holtz, Sensorless speed and position control of synchronous machines using alternating carrier injection, Record of IEEE–IEMDC-2003, vol. 2, 2003, pp. 1211–1217.
176. T.J.E. Miller, Switched Reluctance Motors and Their Control, Oxford University Press, Oxford, 1993.
177. R. Krishnan, Switched Reluctance Motor Drives, CRC Press, Boca Raton, FL, 2001.
178. T.J.E. Miller, Optimal design of switched reluctance motors, IEEE Trans., IE-49, 1, 2002, pp. 15–17.
179. M. Rahman, B. Fahimi, G. Suresh, A.V. Rajarathnam, and M. Eshani, Advantages of switched reluctance motor application to EV and HEV: design and control issue, IEEE Trans., IA-36, 1, 2000, pp. 111–121.
180. D.A. Torrey, Switched reluctance generators and their control, IEEE Trans., EC-49, 1, 2002, pp. 3–14.
181. V.V. Athani, and V.M. Walivadeker, Equivalent circuit for switched reluctance motor, EMPS J., 22, 4, 1994, pp. 533–543.
182. M. Ilic-Spong, M. Marino, S. Peresada, and D. Taylor, Feedback linearizing control of switched reluctance motor, IEEE Trans., AC-32, 5, 1987, pp. 371–379.
183. A.V. Radun, Design consideration of switched reluctance motor, Record of IEEE–IAS-1994 Annual Meeting, 1994.
184. A.V. Radun, C.A. Ferreira, and E. Richter, Two-channel switched reluctance starter–generator results, IEEE Trans., IA-34, 5, 1998, pp. 1106–1109.
185. D.E. Cameron, and J.M. Lang, The control of high speed variable reluctance generators in electric power system, IEEE Trans., IA-29, 6, 1993, pp. 1106–1109.
186. T. Sawata, Ph. Kjaer, C. Cossar, and T.J.E. Miller, Fault tolerant operation of single-phase switched reluctance generators, Record of IEEE–APEC-1997 Annual Meeting, 1997.
187. I. Husain, Minimization of torque ripple SRM drives, IEEE Trans., IE-49, 1, 2002, pp. 28–39.
188. H. Bausch, A. Grief, K. Kanelis, and A. Mickel, Torque control of battery-supplied switched reluctance drives for electrical vehicles, Record of ICEM-1998, Istanbul, Turkey, 1998, pp. 229–234.
189. M.S. Islam, M.M. Anwar, and I. Husain, A sensorless wide-speed range SRM drive with optimally designed critical rotor angles, Record of IEEE–IAS-2000 Annual Meeting, 2000.
190. R.B. Inderka, and R.W. De Doncker, Simple average torque estimation for control of switched reluctance machines, Record of EPE–PEMC-2000, vol. 5, Kosice, 2000, pp. 176–181.
191. K.M. Rahman, and S.E. Shultz, High-performance fully digital switched reluctance motor controller for vehicle propulsion, IEEE Trans., IA-38, 4, 2002, pp. 1062–1071.
192. R.B. Inderka, M. Menne, and R. De Donker, Control of switched reluctance drives for electric vehicle applications, IEEE Trans., 49, 1, 2002, pp. 48–53.
193. M. Ehsani, and B. Fahimi, Elimination of position sensor in switched reluctance motor drives: state of the art and future trends, IEEE Trans., 49, 1, 2002, pp. 40–47.
194. P.P. Acarnley, C.D. French, and I.H. Al-Bahadly, Position estimation in switched reluctance drives, Record of EPE-1995 Conference, Sevilla, 1995, pp. 3765–3770.
195. G. Lopez, P.C. Kjaer, and T.J.E. Miller, High grade position estimation for SRM using flux linkage current correction mode, Record of IEEE–IAS-1998 Annual Meeting, 1998, pp. 731–738.
196. R.D. Lorenz, and N.J. Nagel, Rotating vector methods for sensorless, smooth torque control of switched reluctance motor drive, Record of IEEE–IAS-1998 Annual Meeting, vol. 1, 1998, pp. 723–730.
197. P. Chancharoensoon, and M.F. Rahman, Control of a four-phase switched reluctance generator: experimental investigations, Record of IEEE–IEMDC-2003, vol. 1, Madison, WI, 2003, pp. 842–848.
198. S. Dixon, and B. Fahimi, Enhancement of output electric power in switched reluctance generators, Record of IEEE–IEMDC-2003, vol. 2, Madison, WI, 2003, 2, pp. 849–856.
199. B. Fahimi, A. Emadi, and R.B. Sepe Jr., Position sensorless control: presenting a technology ready for switched reluctance machine drive applications, IEEE–IA Magazine, 10, 1, 2004, pp. 40–47.
200. T.J. Miller, Brushless PM and Reluctance Motor Drives, Clarendon Press, Oxford, 1989.
201. S.A. Nasar, I. Boldea, and L.E. Unnewehr, PM, Reluctance and Selfsynchronous Motors, CRC Press, Boca Raton, FL, 1993.
202. T.J.E. Miller, and J. Hendershot, Design of PM Brushless Motors, Clarendon Press, Oxford, 1994.
203. D.C. Hanselman, Brushless PM Motor Design, Marcel Dekker, New York, 1997.
204. J.F. Gieras, and M. Wing, Permanent Magnet Motor Technology, Marcel Dekker, New York, 2002.
205. K. Sitapati, and R. Krishnan, Performance comparisons between radial and axial field PM brushless machines, IEEE Trans., IA-37, 5, 2001, pp. 1219–1226.
206. A. Covagnino, M. Lazzari, F. Profumo, and A. Tenconi, A comparison between axial flux and radial flux PM synchronous motors, IEEE Trans., IA-38, 6, 2002, pp. 1517–1524.
207. E. Spooner, and A. Williamson, Modular PM wind-turbines generators, Record of IEEE–IAS-1996 Annual Meeting, vol. 1, 1996, pp. 497–502.
208. J. Cros, and P. Viarouge, Synthesis of high performance PM motors with concentrated windings, IEEE Trans., EC-17, 2, 2002, pp. 248–253.
209. F. Magnussen, and C. Sadarangani, Winding factors and Joule losses of PM machines with concentrated windings, Record of IEEE–IEMDC-2003, vol. 1, 2003, pp. 333–339.
210. Z.Q. Zhu, D. Howe, E. Bolte, and B. Ackerman, Instantaneous magnetic field distribution brushless PM d.c. motors, Parts I, II, III, IV, IEEE Trans., MAG-29, 1, 1993, pp. 124–158.
211. A.B. Proca, A. Keyhani, A. El-Antably, W. Lu, and M. Dai, Analytical model for permanent magnet motors with surface mounted magnets, IEEE Trans., EC-18, 3, 2003, pp. 386–391.
212. J. Azzouzi, G. Barakat, and B. Dakyo, Quasi 3D analytical modeling of magnetic field of axial flux PMSM, Record of IEEE–IEMDC-2003, vol. 3, 2003, pp. 1941–1946.
213. A. Parviainen, M. Niemala, and J. Pyrhonen, Modeling of axial flux PM machines, Record of IEEE–IEMDC-2003, vol. 3, 2003, pp. 1955–1961.
214. L. Ma, M. Sanada, S. Morimoto, and Y. Takeda, Prediction of iron loss in rotating machines with rotational losses included, IEEE Trans., MAG-39, 4, 2003, pp. 2036–2041.
215. A. Munoz-Garcia, and D.W. Novotny, Characterization of third harmonic-induced voltages in PM generators, Record of IEEE–IAS-1996 Annual Meeting, vol. 1, 1996, pp. 525–532.
216. D.-H. Che, H.-K. Jung, and D.-J. Sim, Multiobjective optimal design of interior PM synchronous motors considering improved core loss formulae, IEEE Trans., EC-14, 4, 1999, pp. 1347–1352.
217. V. Honsinger, Performance of poliphase PM machines, IEEE Trans., PAS-99, 6, 1980, pp. 1510–1517.
218. O. Ojo, and J. Cox, Investigation into the performance characteristic of an IPM generator including saturation effects, Record of IEEE–IAS-1996, vol. 1, 1996, pp. 533–540.
219. I. Boldea, and S.A. Nasar, Electric Drives, CRC Press, Boca Raton, FL, 1998.
220. M.A. Rahman, A.M. Osheiba, and T.S. Radwan, Modelling and controller design of an insulated diesel engine permanent magnet synchronous generator, IEEE Trans., EC-11, 2, 1996, pp. 324–330.
221. D.C. Aliprantis, S.A. Papathanassiou, M.P. Papadopoulos, and A.G. Kladar, Modeling and control of variable-speed wind turbine equipped with PM synchronous generator, Record of ICEM-2000, Espoo, Finland vol. 1, 2000, pp. 558–562.
222. B.S. Borowy, and Z.M. Salameh, Dynamic response of a stand-alone wind energy conversion system with battery energy storage to a wind gust, IEEE Trans., EC-12, 1, 1997, pp. 73–78.
223. L.M. Tolbert, W.A. Peterson, T.J. Theiss, and M.B. Scudiere, Gen-sets, IEEE–IA Magazine, 9, 2, 2003, pp. 48–54.
224. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
225. H. Polinder, On the Losses in a High-Speed Permanent-Magnet Generator with Rectifier with Special Attention to the Effect of a Damper Cylinder, Ph.D. thesis, University of Delft, the Netherlands, 1998.
226. A. Diop, and U. Schröder, Experimental losses determination of high speed synchronous machines 70 kW–45,000 rpm with magnetic bearings, Record of ICEM-1992, vol. 3, Manchester, U.K., 1992, pp. 2106–2110.
227. A. Castagnini, M. Garavaghia, F. Moriconi, and G. Secondo, Development of a high speed and power synchronous PM motor, Record of ICEM-1992, Manchester, U.K., 1992
228. B.P. James, and D.A.T. Al Zahawi, A high speed alternator for small scale gas turbines CHP unit, Record of International Conference on Electrical Machines and Drives, IEE publication no. 412, 1995.
229. A. Castagnini, and I. Leone, Test results of a very high speed PM brushless motor, Record of ICEM-2002.
230. Z.J.J. Offringa, R.W.P. Kerkenaar, and J.L.F. Van der Veen, A high speed 1400 kW PM generator with rectifier, Record of ICEM-2000, vol. 1, Espoo, Finland, 2000, pp. 308–313.
231. V. Callea, S. Elia, M. Pasquali, M.B. Sabene, and E. Santini, Ultra high-speed electric generator for gas turbine series utility, Record of EVS Congress, Berlin, 2001.
232. W. Vetter, A. Collotti, and K. Reichert, A new motor/generator for flywheel applications, Record of ICEM-1998, vol. 1, Istanbul, Turkey, 1998, pp. 348–352.
233. R. Hebner, J. Beno, and A. Walls, Flyweel batteries come around again, IEEE Spectrum, 4, April 2002, pp. 46–51.
234. A. Dittrich, Compensation of current harmonics in doubly-fed induction generator system, Record of EPE-2001, Graz, Austria, 2001, pp. P1–P8.
235. G. Podder, A. Joseph, and A.K. Unnikrishnan, Sensorless variable-speed controller for existing fixed-speed wind power generator with unity power-factor operation, IEEE Trans., IE-50, 5, 2003, pp. 1007–1015.
236. E.A.A. Coelho, P.C. Cortizo, and P.F.D. Garcia, Small-signal stability for parallel-connected inverters in stand-alone A.C. supply systems, IEEE Trans., IA-38, 2, 2002, pp. 533–542.
237. B.H. Bae, S.-K. Sul, J.-H. Kwon, and J.-S. Byeon, Implementation of sensorless vector control for super-high-speed PM–SM of turbo-compressor, IEEE Trans., IA-39, 3, 2003, pp. 811–818.
238. K.-H. Kein, and M.-J. Youn, DSP-based high-speed sensorless control for a brushless D.C. motor using a D.C. link voltage control, EPCS J., 30, 9, 2002, pp. 889–906.
239. H.J. Gutt, and J. Müller, New aspects for developing and optimizing modern motor car generators, Record of IEEE–IAS-1994 Annual Meeting, vol. 1, 1994, pp. 3–7.
240. M. Comanescu, A. Keyhani, and M. Dai, Design and analysis of a 42 V permanent magnet generator for automotive applications, IEEE Trans., EC-18, 1, 2003, pp. 107–112.
241. D. Gay, Composite iron powder for A.C. electromagnetic applications: history and use, Record of SMMA Fall Conference, Chicago, October 4–6, 2000.
242. E.A. Knoth, Motors for 21st century, Record of SMMA-2000, Fall Conference, Chicago, October 4–6, 2000.
243. H.P. Nee, L. Lefeure, P. Thelin, and J. Soulard, Determination of D and Q reactances of PM synchronous motors without measurements of the rotor position, IEEE Trans., IA-36, 5, 2000, pp. 1330–1335.
244. T.J.E. Miller, Methods for testing permanent magnet polyphase A.C. motors, Record of IEEE–IAS-1981, vol. 1, 1981, pp. 494–499.
245. J.D. Ede, Z.Q. Zhu, and D. Howe, Rotor resonances of high speed PM brushless machines, IEEE Trans., IA-38, 6, 2002, pp. 1542–1548.
246. I. Boldea, L. Tutelea, and C.I. Pitic, PM-assisted reluctance synchronous motor/generator (PM-RSM), for mild hybrid vehicles: electromagnetic design, IEEE Trans., IA-40, 2, 2004, pp. 492–498.
247. P.H. Mellor, S.G. Burrow, T. Sawata, and M. Holme, A wide speed range permanent magnet generator for future embedded aircraft generation systems, Record of IEEE–IEMDC-2003, vol. 3, 2003, pp. 1308–1313.
248. C.A. Ferreira, S.R. Jones, W.S. Heglund, and W.D. Jones, Detailed design of a 30 kW switched reluctance starter-generator system for gas turbine application, IEEE Trans., IA-31, 3, 1995, pp. 553–561.
249. J.A. Weimer, The role of electric machines and drives in the more electric aircraft, Record of IEEE–IEMDC, vol. 1, 2003, pp. 11–15.
250. A.S. Meris, N.A. Voues, and G.B. Giannakopoulos, A variable speed wind energy conversion scheme for connecting to weak A.C. systems, IEEE Trans., EC-14, 1, 1999, pp. 122–127.
251. H. Weh, and H. May, Achievable force densities, Record of ICEM-1996, München, Germany, vol. 3, 1996, pp. 1101–1111.
252. J. Luo, S. Huang, S. Chen, and T.A. Lipo, Design and experiments of a novel axial circumferential current permanent magnet machine (AFCCM) with radial airgap, Record of IEEE–IAS, 2001, Annual Meeting, 2001.
253. G. Henneberger, and I.A. Viorel, Variable Reluctance Electrical Machines, Shaker-Verlag, Aachen, 2001, chap. 6.
254. I. Boldea, J. Zhang, and S.A. Nasar, Theoretical characterization of flux reversal machine in low speed drives — the pole-PM configuration, IEEE Trans., IA-38, 6, 2002, pp. 1549–1557.
255. S.E. Rauch, and L.J. Johnson, Design principles of flux switch alternator, AIEE Trans., part III, 1955, pp. 1261–1268.
256. A. Njeh, A. Masmoudi, and A. El Antably, 3D FEA based investigation of cogging torque of claw pole transverse flux PM machine, Record of IEEE–IEMDC, vol. I, 2003, pp. 319–324.
257. M. Bork, R. Blissenbach, and G. Henneberger, Identification of the loss distribution in a transverse flux machine, Record of ICEM, vol. 3, Istanbul, Turkey, 1998, pp. 1826–1831.
258. I. Boldea, E. Serban, and R. Babau, Flux-reversal stator-PM single phase generator with controlled DC output, Record of OPTIM, vol. 4, Poiana Brasov, Romania, 1996, pp. 1124–1134.
259. R. Deodhar, S. Andersson, I. Boldea, and T.J.E. Miller, The flux reversal machine: a new brushless doubly-salient PM machine, IEEE Trans., IA-33, 4, pp. 925–934.
260. I. Boldea, C.X. Wang, and S.A. Nasar, Design of a three-phase flux reversal machine, Electr. Mach. Power Syst., 27, 1999, pp. 849–863.
261. C.X. Wang, S.A. Nasar, and I. Boldea, Three-phase flux reversal machine, Proc. IEE, EPA-146, 2, 1999, pp. 139–146.