The behavior of thrust washer bearings considering mixed lubrication and asperity contact

Tribology Transactions

Volumn 49, Issue 2, 2006, Pages 233-247

  Jackson, Robert L ^a   Green, Itzhak ^a  

^a GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 85015670187     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/05698190600614841     Document Type: Article

References (21)

1. Jacksons R. L. and Green, I. (2001), “Study of the Tribological Behavior of a Thrust Washer Bearing,” Trib. Trans., 44(3), pp 504-508.
2. Jackson, R. L. and Green, I. (2003), “Experimental Analysis of the Wear, Life and Behavior of PTFE Coated Thrust Washer Bearings under Non-axisymmetric Loading,” Trib. Trans., 46(4), pp 600-607.
3. Cameron, A. and Wood, W. L. (1958), “Parallel Surface Thrust Bearing,” ASLE Trans., 1, pp 254-258.
4. Kazama, T. and Yamaguchi, A. (1993), “Application of a Mixed Lubrication Model for Hydrostatic Thrust Bearings of Hydraulic Equipment,” ASME J. Tribol., 115, pp 686-691.
5. Patir, N. and Cheng, H. S. (1978), “An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication,” ASME J. Tribol., 100, pp 12-17.
6. Patir, N. and Cheng, H. S. (1979), “Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces,” ASME J. Tribol., 101, pp 220-230.
7. Yu, T. and Sadeghi, F. (2001), “Groove Effects on Thrust Washer Lubrication,” ASME J. Tribol., 123(1), pp 295-304.
8. Yu, T. and Sadeghi, F. (2002), “Thermal Effects in Thrust Washer Lubrication,” ASME J. Tribol., 123(1), pp 166-177.
9. Kucinschi, B. R., DeWitt, K. J. and Pascovici, M. D. (2004), “Thermoelas-tohydrodynamic (TEHD) Analysis of a Grooved Thrust Washer,” ASME J. Tribol., 126, pp 267-274.
10. Reddy, J. N. (1993), “An Introduction to the Finite Element Method,” 2nd Ed., Mcgraw-Hill, NewYork.
11. Jackson, R. L. and Green, I. (2004), “A Finite Element Study of Elasto-Plastic Hemispherical Contact,” ASME J. Tribol., 127(2), pp 343-354.
12. Jackson, R. L. and Green, I., “A Statistical Model of Elasto-Plastic Asperity Contact of Rough Surfaces,” Proc. Of the 2003 ASME/STLE International Tribology Conference, Preprint 2003-TRIB 268.
13. Quicksall, J., Jackson, R. L. and Green, I. “Elasto-Plastic Hemispherical Contactfor Varying Mechanical Properties,” IMech EJ. Of Eng. Trib.-Part J, 218, pp 313-322.
14. Front, I. (1990), “The Effects of Closing Force and Surface Roughness on Leakage in Radial Face Seals,” MS Thesis, Technion, Israel Institute of Technology.
15. McCool, J. I. (1986), “Comparison of Models for the Contact of RoughSurfaces,” Wear, 107, pp 37-60.
16. Roelands, C. J. A. (1966), “Correlational Aspects of the Viscosity-Temperature-Pressure Relationship of Lubricating Oils. Druk,” V. R. B., Groingen, Netherlands.
17. Chang, W. R., Etsion, I. and Bogy, D. B. (1988), “Static Friction Coefficient Model for Metallic Rough Surfaces,” ASME J. Tribol., 110, pp 5763.
18. Etsion, I. and Amit, M. (1993), “The Effect of Small Normal Loads on the StaticFriction Coefficient for Very Smooth Surfaces,” ASME J. Tribol., 115, pp 406-410.
19. Roy Chowdhury, S. K. and Ghosh, P. (1994), “Adhesion and Adhesional Friction at the Contact Between Solids,” Wear, 174, pp 9-19.
20. Kogut, L. and Etsion, I. (2003), “A Semi-Analytical Solution for the Sliding Inception of a Spherical Contact,” ASME J. Tribol, 125(3), pp 499-506.
21. Ozisik, M. N. (1993), Heat Conduction, 2nd Ed., John Wiley, New York.