Experimental investigation on galling performance of tool steel in stamping of UHSS sheets

International Journal of Precision Engineering and Manufacturing

Volumn 15, Issue 6, 2014, Pages 1101-1107

  Choi, Hong Seok ^a   Kim, Sung Gwi ^a   Seo, Pan Ki ^b   Kim, Byung Min ^a   Cha, Byung Chul ^c   Ko, Dae Cheol ^a  

^a Pusan National University   (South Korea)

^b Shinyoung Co Ltd   (South Korea)

^c Korea Institute of Industrial Technology   (South Korea)

Author keywords

Friction coefficient; Galling performance; Stamping; Surface roughness parameter; Tool steel; Ultra high strength steel sheet

Indexed keywords

ADVANCED HIGH STRENGTH STEEL; ALUMINUM ALLOYS; CHROMIUM ALLOYS; COATINGS; FRICTION; HIGH STRENGTH STEEL; HIGHER ORDER STATISTICS; STAMPING; STEEL TESTING; SURFACE ROUGHNESS; SURFACE TESTING; TITANIUM ALLOYS; TOOL STEEL; TOOLS; TOPOGRAPHY;

AVERAGE SURFACE ROUGHNESS; COEFFICIENT OF FRICTIONS; EXPERIMENTAL INVESTIGATIONS; FRICTION COEFFICIENTS; GALLING PERFORMANCE; SLIDING DISTANCES; SURFACE CONDITIONS; SURFACE ROUGHNESS PARAMETERS;

CHROMIUM STEEL;

EID: 84901916822     PISSN: 22347593     EISSN: 20054602     Source Type: Journal    
DOI: 10.1007/s12541-014-0443-5     Document Type: Article

References (18)

1. Gaard, A., Krakhmalev, P., and Bergström, J., "Wear Mechanisms in Deep Drawing of Carbon Steel-Correlation to Laboratory Testing," Tribotest, Vol. 14, No. 1, pp. 1-9, 2008.
2. Kim, H., Han, S., Yan, Q., and Altan, T., "Evaluation of Tool Materials, Coatings and lubricants in Forming Galvanized Advanced High Strength Steels (AHSS)," CIRP Annals-Manufacturing Technology, Vol. 57, No. 1, pp. 299-304, 2008.
3. Cora, Ö. N. and Koç, M., "Experimental Investigations on Wear Resistance Characteristics of Alternative Die Materials for Stamping of Advanced High-Strength Steels (AHSS)," International Journal of Machine Tools and Manufacture, Vol. 49, No. 12, pp. 897-905, 2009.
4. Sresomroeng, B., Premanond, V., Kaewtatip, P., Khantachawana, A., and Koga, N., "Evaluation of Ti-Based Ceramic Coated Tools to Reduce Adhesion in U-Channel Forming Process of High Strength Steel," Steel Research International, Vol. 81, No. 9, pp. 829-832, 2010.
5. Eriksson, J. and Olsson, M., "Tribological Testing of Commercial CrN,(Ti, Al) N and CrC/C PVD Coatings-Evaluation of Galling and Wear Characteristics against Different High Strength Steels," Surface and Coatings Technology, Vol. 205, No. 16, pp. 4045-4051, 2011.
6. Karlsson, P., Gaard, A., Krakhmalev, P., and Bergström, J., "Galling Resistance and Wear Mechanisms for Cold-Work Tool Steels in Lubricated Sliding against High Strength Stainless Steel Sheets," Wear, Vol. 286, pp. 92-97, 2012.
7. Cora, O. N., Aǧcayaz, A., Namiki, K., Sofuoǧlu, H., and Koç, M., "Die Wear in Stamping of Advanced High Strength Steels-Investigations on the Effects of Substrate Material and Hard-Coatings," Tribology International, Vol. 52, pp. 50-60, 2012.
8. Ahn, D. G., "Hardfacing Technologies for Improvement of Wear Characteristics of Hot Working Tools: A Review," Int. J. Precis. Eng. Manuf., Vol. 14, No. 7, pp. 1271-1283, 2013.
9. Podgornik, B. and Jerina, J., "Surface Topography Effect on Galling Resistance of Coated and Uncoated Tool Steel," Surface and Coatings Technology, Vol. 206, No. 11, pp. 2792-2800, 2012.
10. Podgornik, B., Hogmark, S., and Sandberg, O., "Proper Coating Selection for Improved Galling Performance of Forming Tool Steel," Wear, Vol. 261, No. 1, pp. 15-21, 2006.
11. Podgornik, B., Hogmark, S., and Sandberg, O., "Influence of Surface Roughness and Coating Type on the Galling Properties of Coated Forming Tool Steel," Surface and Coatings Technology, Vol. 184, No. 2, pp. 338-348, 2004.
12. Sedlaček, M., Podgornik, B., and Vižintin, J., "Influence of Surface Preparation on Roughness Parameters, Friction and Wear," Wear, Vol. 266, No. 3, pp. 482-487, 2009.
13. Saini, S., Ahuja, I. S., and Sharma, V. S., "Influence of Cutting Parameters on Tool Wear and Surface Roughness in Hard Turning of AISI H11 Tool Steel using Ceramic Tools," Int. J. Precis. Eng. Manuf., Vol. 13, No. 8, pp. 1295-1302, 2012.
14. Harlin, P., Bexell, U., and Olsson, M., "Influence of Surface Topography of Arc-Deposited TiN and Sputter-Deposited WC/C Coatings on the Initial Material Transfer Tendency and Friction Characteristics under Dry Sliding Contact Conditions," Surface and Coatings Technology, Vol. 203, No. 13, pp. 1478-1755, 2009.
15. Schedin, E. and Lehtinen, B., "Galling Mechanisms in Lubricated Systems: a Study of Sheet Metal Forming," Wear, Vol. 170, No. 1, pp. 119-130, 1993.
16. Podgornik, B., Hogmark, S., and Pezdirnik, J., "Comparison between Different Test Methods for Evaluation of Galling Properties of Surface Engineered Tool Surfaces," Wear, Vol. 257, No. 7, pp. 843-851, 2004.
17. Fischer-Cripps, A. C., "Nanoindentation," Springer-Verlag GmbH, pp. 1-4, 2002.
18. Bhushan, B., "Principles and Applications of Tribology," Wiley, pp. 102-121, 1999.