Estimating the cohesive zone model parameters of carbon nanotube-polymer interface for machining simulations

Journal of Manufacturing Science and Engineering

Volumn 136, Issue 3, 2014, Pages

  Jiang, Lingyun ^a   Nath, Chandra ^a   Samuel, Johnson ^b   Kapoor, Shiv G ^a  

^a UNIVERSITY OF ILLINOIS AT URBANA CHAMPAIGN   (United States)

^b RENSSELAER POLYTECHNIC INSTITUTE   (United States)

Author keywords

3D microstructure level modeling; CNT polymer interface; cohesive zone model; inverse finite element analysis

Indexed keywords

3D MODELING; CARBON NANOTUBES; FINITE ELEMENT METHOD; INVERSE PROBLEMS; MICROSTRUCTURE; NANOINDENTATION; POLYMERS;

COHESIVE ZONE MODEL; COMPOSITE MICROSTRUCTURES; INTERFACIAL FRACTURE ENERGY; INVERSE FINITE ELEMENT ANALYSIS; LEVEL MODEL; NANOINDENTATION LOAD-DISPLACEMENT CURVES; POLY (VINYL ALCOHOL) (PVA); POLYMER INTERFACES;

FAILURE (MECHANICAL);

EID: 84897411228     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4024941     Document Type: Article

References (31)

1. Lu, J. P., 1997, "Elastic Properties of Carbon Nanotubes and Nanoropes," Phys. Rev. Lett. http://dx.doi.org/10.1103/PhysRevLett.79.1297, 79, pp. 1297-1300. (Pubitemid 127658418)
2. Peng, B., Locascio, M., Zapol, P., Li, S., Mielke, S. L., Schatz, G. C., and Espi-nosa, H. D., 2008, "Measurements of Near-Ultimate Strength for Multiwalled Carbon Nanotubes and Irradiation-Induced Crosslinking Improvements," Nat. Nanotechnol. http://dx.doi.org/10.1038/nnano.2008.211, 3, pp. 626-631.
3. Stewart, R., 2004, "Nanocomposites: Microscopic Reinforcement Boost Polymer Performance," Plast. Eng., 60, pp. 22-29.
4. Endo, M., Hayashi, T., Kim, Y. A. K., and Muramatsu, H., 2006, "Development and Application of Carbon Nanotubes," Jpn. J. Appl. Phys. http://dx.doi.org/10.1143/JJAP.45.4883, 45, pp. 4883-4892. (Pubitemid 43925002)
5. Eklund, P., Ajayan, P., Blackmon, R., Hart, A. J., Kong, J., Pradhan, B., Rao, A., and Rinzler, A., 2007, "International Assessment of Research and Development on Carbon Nanotubes Manufacturing and Application" World Technology Evaluation Center (WTEC) Panel Report.
6. Dikshit, A., Samuel, J., DeVor, R. E., and Kapoor, S. G., 2008, "Microstructure-Level Machining Simulation of Carbon Nanotube-Reinforced Polymer Composites-Part I: Model Development and Validation," ASME J. Manuf. Sci. Eng. http://dx.doi.org/10.1115/1.2917378, 130, p. 031114.
7. Dikshit, A., Samuel, J., DeVor, R. E., and Kapoor, S. G., 2008, "Microstructure-Level Machining Simulation of Carbon Nanotube-Reinforced Polymer Composites-Part II: Model Interpretation and Application," ASME J. Manuf. Sci. Eng. http://dx.doi.org/10.1115/1.2927431, 130, p. 031115.
8. Dikshit, A., Samuel, J., DeVor, R. E., and Kapoor, S. G., 2008, "A Microstruc-ture-Level Material Model for Simulating the Machining of Carbon Nanotu-be-Reinforced Polymer Composites," ASME J. Manuf. Sci. Eng. http://dx.doi.org/10.1115/1.2917564, 130, p. 031110.
9. Samuel, J., DeVor, R. E., Kapoor, S. G., and Hsia, K. J., 2005, "Experimental Investigation of the Machinability of Polycarbonate Reinforced with Multi-Walled Carbon Nanoutbes," ASME J. Manuf. Sci. Eng., 128, pp. 465-473. (Pubitemid 43952200)
10. Samuel, J., DeVor, R. E., Kapoor, S. G., and Hsia, K. J., 2010, "Effect of Microstructural Parameters on the Machinability of Aligned Carbon Nanotube Composites," ASME J. Manuf. Sci. Eng. http://dx.doi.org/10. 1115/1.4002495, 132, p. 051012.
11. Ortiz, M., and Pandolfi, A., 1999, "Finite-Deformation Irreversible Cohesive Elements for Three-Dimensional Crack-Propagation Analysis," Int. J. Numer. Methods Eng. http://dx.doi.org/10.1002/(SICI)1097-0207(19990330)44: 9%3c1267:AID-NME486%3e3.0.CO;2-7, 44, pp. 1267-1282.
12. Camanho, P. P., Davila, C. G., and de Moura, M. F., 2003, "Numerical Simulation of Mixed-Mode Progressive Delamination in Composite Materials," J. Compos. Mater. http://dx.doi.org/10.1177/0021998303034505, 37, pp. 1415-1438.
13. Golestanina, H., and Shojaie, M., 2010, "Numerical Characterization of CNT-Based Polymer Composites Considering Interface Effects," Comput. Mater. Sci. http://dx.doi.org/10.1016/j.commatsci.2010.10.003, 50, pp. 731-736.
14. Shokrieh, M. M., and Rafiee, R., 2010, "On the Tensile Behavior of an Embedded Carbon Nanotube in Polymer Matrix With Non-Bond Interphase Region," Compos. Struct. http://dx.doi.org/10.1016/j.compstruct.2009.09. 033, 92, pp. 647-652.
15. Strus, M. C., Cano, C. I., Pipes, R. B., Nguyen, C. V., Raman, A., 2009, "Interfacial Energy Between Carbon Nanotubes and Polymers Measured From Nanoscale Peel Test in the Atomic Force Microscope," Compos. Sci. Technol. http://dx.doi.org/10.1016/j.compscitech.2009.02.026, 69, pp. 1580-1586.
16. Frankland, S. J. V., Harik, V. M., Odegard, G. M., Brenner, D. W., and Gates, T. S., 2003, "The Stress-Strain Behavior of Polymer-Nanotube Composite from Molecular Dynamic Simulation," Compos. Sci. Technol. http://dx.doi.org/10.1016/S0266-3538(03)00059-9, 63, pp. 1655-1661. (Pubitemid 36906680)
17. Cooper, C. A., Cohen, S. R., Barber, A. H., and Wagner, H. D., 2002, "Detachment of Nanotube From Polymer Matrix," Appl. Phys. Lett. http://dx.doi.org/10.1063/1.1521585, 81, pp. 3873-3875.
18. Liu, K., VanLandingham M. R., and Ovaert T. C., 2009, "Mechanical Characterization of Soft Viscoelastic Gels via Indentation and Optimization-Based Inverse Finite Element Analysis," J. Mech. Behav. Biomed. Mater. http://dx.doi.org/10.1016/j.jmbbm.2008.12.001, 2, pp. 355-363.
19. Pavia, M. C., Zhou, B., Fernando K. A. S., Lin Y., Kennedy J. M., and Sun Y.-P., 2004, "Mechanical and Morphological Characterization of Polymer-Carbon Nanocomposites From Functionalized Carbon Nanotubes," Carbon http://dx.doi.org/10.1016/j.carbon.2004.06.031, 42, pp. 2849-2854.
20. Zhao, B., Wang, J., Li, Z., Liu, P., Chen, D., Zhang Y. 2008, "Mechanical Strength Improvement of Polypropylene Threads Modified by PVA/CNT Composite Coatings," Mater. Lett. http://dx.doi.org/10.1016/j. matlet.2008.07.037, 62, pp. 4380-4382.
21. Pradhan, B., Kohlmeyer R. R., and Chen J., 2010, "Fabrication of In-Plane Aligned Carbon Nanotube-Polymer Composite Thin Films," Carbon http://dx.doi.org/10.1016/j.carbon.2009.09.006, 48, pp. 217-222.
22. Lichinchi, M., and Lenardi, C., 1998, "Simulation of Berkovich Nanoindenta-tion Experiments on Thin Films Using Finite Element Method," Thin Solid Films http://dx.doi.org/10.1016/S0040-6090(97)00739-6, 312, pp. 240-248. (Pubitemid 128388945)
23. Yu, M. F., Lourie, O., Dyer, M. J., Moloni, K., Kelly, T. F., and Ruoff, R. S., 2000, "Strength and Breaking Mechanism of Multiwalled Carbon Nanotubes Under Tensile Load," Science http://dx.doi.org/10.1126/science. 287.5453.637, 287, pp.637-640. (Pubitemid 30070908)
24. Hou, Y., Tang, J., Zhang, H., Qian, C., Feng, Y., and Liu, J., 2009, "Functionalized Few-Walled Carbon Nanotubes for Mechanical Reinforcement of Polymeric Composites," ACS Nano http://dx.doi.org/10.1021/nn9000512, 3, pp. 1057-1062.
25. Oliver, W. C., and Pharr, G. M. 1992, "An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments," J. Mater. Res. http://dx.doi.org/10.1557/JMR. 1992.1564, 7, pp. 1564-1583.
26. Lohnert, S., and Wriggers, P., 2003, "Homogenization of Microheterogneous Materials Considering Interfacial Delamination at Finite Strains," Tech. Mech., 23, pp. 167-177.
27. Calzada, K. A., Kapoor, S. G., DeVor, R. E., Samuel, J., and Srivastava, A. K., 2011, "Modeling and Interpretation of Fiber Orientation-Based Failure Mechanisms in Machining of Carbon Fiber-Reinforced Polymer Composites" Trans. North Am. Manuf. Res. Inst. SME, 39, pp. 332-341.
28. Xu, X. P., and Needleman, A., 1994, "Numerical Simulations of Fast Crack Growth in Brittle Solids," J. Mech. Phys. Solids http://dx.doi.org/ 10.1016/0022-5096(94)90003-5, 42, pp.1397-1434.
29. van den Bosch, M. J., Schreurs, P. J. G., and Geers, M. G. D., 2006, "An Improved Description of the Exponential Xu and Needleman Cohesive Zone Law for Mixed-Mode Decohesion," Eng. Fract. Mech. http://dx.doi.org/10. 1016/j.engfracmech.2005.12.006, 73, pp. 1220-1234.
30. Wang, J., Piechna, J., Yume, J. A. O., and Muller, N., 2012, "Stability Analysis in Wound Composite Material Axial Impeller," Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci. http://dx.doi.org/10.1177/ 0954406211420335, 226, pp. 1162-1172.
31. McMinis J., Crombez, R., Montalvo, E., and Shen, W., 2007, "Determination of the Cross-Sectional Area of the Indenter in Nano-Indentation Test," Phys. B: Condens. Matter http://dx.doi.org/10.1016/ j.physb.2006.09.006, 391, pp. 118-123. (Pubitemid 46216031)