Effect of microstructural parameters on the machinability of aligned carbon nanotube composites

Journal of Manufacturing Science and Engineering

Volumn 132, Issue 5, 2010, Pages

  Samuel, Johnson ^a   Kapoor, Shiv G ^a   Devor, Richard E ^a   Hsia, K Jimmy ^a  

^a University of Illinois at Urbana Champaign   (United States)

Author keywords

aligned CNT composites; FEM models; micromachining

Indexed keywords

DISPERSIONS; MACHINABILITY; MICROMACHINING; MICROSTRUCTURE; MORPHOLOGY; SURFACE MORPHOLOGY; SURFACE ROUGHNESS;

ALIGNED CARBON NANOTUBES; CHIP MORPHOLOGIES; CNT COMPOSITES; CUTTING-DIRECTION; FEM MODELS; MACHINING SIMULATION; MICRO-FLUIDIC DEVICES; MICROSTRUCTURAL PARAMETERS;

CARBON NANOTUBES;

EID: 78650015539     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4002495     Document Type: Article

References (26)

1. Hyuga, H., Jones, M. I., Hirao, K., and Yamauchi, Y., 2005, "Friction and Wear Properties of Si3N4/Carbon Fiber Composites With Aligned Microstructure, " J. Am. Ceram. Soc, 88(5), pp. 1239-1243.
2. Papathanasiou, T. D., Ingber, M. S., and Guell, D. C., 1995, "Stiffness Enhancement in Aligned, Short-Fibre Composites: A Computational and Experimental Investigation, " Compos. Sci. Technol., 54(1), pp. 1-9.
3. Thostenson, E. T., and Chou, T. W., 2002, "Aligned Multi-Walled Carbon Nanotube-Reinforced Composites: Processing and Mechanical Characterization, " J. Phys. D: Appl. Phys., 35, pp. L77-L80.
4. Xie, X., Mai, Y., and Zhou, X., 2005, "Dispersion and Alignment of Carbon Nanotubes in Polymer Matrix: A Review, " Mater. Sci. Eng. R., 49, pp. 89-112.
5. Wang, D. H., Ramulu, M., and Arola, D., 1995, "Orthogonal Cutting Mechanisms of Graphite Epoxy Composite. Part I: Unidirectional Laminate, " Int. J. Mach. Tools Manuf., 35(12), pp. 1623-1638.
6. Koplev, A., 1980, "Cutting of CFRPWith Single Edge Tools, " Proceedings of the Third International Conference on Composite Materials, Paris, pp. 1597-1605.
7. Samuel, J., De Vor, R. E., Kapoor, S. G., and Hsia, K. J., 2006, "Machinability of Polycarbonate Reinforced With Multiwalled Carbon Nanotubes, " ASME J. Manuf. Sci. Eng., 128(2), pp. 465-473.
8. Samuel, J., Dikshit, A., De Vor, R. E., Kapoor, S. G., and Hsia, K. J., 2008, "Effect of Carbon Nanotube (CNT) Loading on the Thermo-Mechanical Properties and the Machinability of CNT-Reinforced Polymer Composites, " ASME Paper No. MSEC-ICMP2008-72028.
9. Ghai, I., Samuel, J., De Vor, R. E., and Kapoor, S. G., 2007, "Effect of Carbon Nanotube Loading on the Machinability of Polycarbonate Nanocomposites, " Proceedings of the International and INCOMM-6 Conference, Future Trends in Composite Materials and Processing, Dec. 12-14.
10. Dikshit, A., Samuel, J., De Vor, R. E., and Kapoor, S. G., 2008, "Microstructure-Level Machining Simulation of Carbon Nanotube Reinforced Polymer Composites-Part 1: Model Development and Validation, " ASME J. Manuf. Sci. Eng., 130(3), p. 0311141.
11. Dikshit, A., Samuel, J., De Vor, R. E., and Kapoor, S. G., 2008, "Microstructure-Level Machining Simulation of Carbon Nanotube Reinforced Polymer Composites-Part 2: Model Interpretation and Application, " ASME J. Manuf. Sci. Eng., 130(3), p. 0311151.
12. Mulliken, A. D., and Boyce, M. C., 2006, "Mechanics of Rate-Dependent Elastic-Plastic Deformation of Glassy Polymers From Low to High Strain Rates, " Int. J. Solids Struct., 43(5), pp. 1331-1356.
13. Dikshit, A., Samuel, J., De Vor, R. E., and Kapoor, S. G., 2008, "A Microstructure-Level Material Model for Simulating the Machining of Carbon Nanotube Reinforced Polymer Composites, " ASME J. Manuf. Sci. Eng., 130(3), p. 0311101.
14. Gearing, B. P., and Anand, L., 2004, "Notch-Sensitive Fracture of Polycarbonate, " Int. J. Solids Struct., 41 (3-4), pp. 827-845.
15. Stuart, B. H., 1997, "Scratch Friction Studies of Polycarbonate, " Polym. Test., 16(5), pp. 517-522.
16. Yakobson, B. I., Campbell, M. P., Brabec, C. J., and Bernholc, J., 1997, "High Strain Rate Fracture and C-Chain Unraveling in Carbon Nanotubes, " Comput. Mater. Sci., 8(4), pp. 341-348.
17. Belytschko, T., Xiao, S. P., Shatz, G. C., and Ruoff, R. S., 2002, "Atomistic Simulations of Nanotube Fracture, " Phys. Rev. B., 65, p. 235430.
18. Meo, M., and Rossi, M., 2006, "Tensile Failure Prediction of Single Wall Carbon Nanotube, " Eng. Fract. Mech., 73, pp. 2589-2599.
19. Xiao, J. R., Gamma, B. A., and Gillespie, J. W., 2005, "An Analytical Molecular Structural Mechanics Model for the Mechanical Properties of Carbon Nanotubes, " Int. J. Solids Struct., 42, pp. 366-371.
20. Lu, J., and Zhang, L., 2006, "Analysis of Localized Failure of Single-Wall Carbon Nanotubes, " Comput. Mater. Sci., 35, pp. 432-441.
21. Samuel, J., 2009, "Fundamental Study on the Machinability of Carbon Nanotube Reinforced Polymer Composites, " Ph. D. thesis, University of Illinois at Urbana-Champaign, Champaign, IL.
22. Pötschke, P., Bhattacharyya, A. R., Janke, A., and Goering, H., 2003, "Melt Mixing of Polycarbonate/Multi-Wall Carbon Nanotube Composites, " Compos. Interfaces, 10 (4-5), pp. 389-404.
23. Lourie, O., and Wagner, H. D., 1999, "Evidence of Stress Transfer and Formation of Fracture Clusters in Carbon Nanotube-Based Composites, " Compos. Sci. Technol., 59, pp. 975-977.
24. Toonder, J., Bos, F., Broer, D., Filippini, L., Gillies, M., Goede, J., Mol, T., Reijme, M., Talen, W., Wilderbeek, H., Khatavkar, V., and Anderson, P., 2008, "Artificial Cilia for Active Micro-Fluidic Mixing, " Lab Chip, 8, pp. 533-541.
25. Zhou, Z., and Liu, Z., 2008, "Biomimetic Cilia Based on MEMS Technology, " J. Bionics Eng., 5, pp. 358-365.
26. Kim, M. J., 2005, "Bacterial Flows: Mixing and Pumping in Microfluidic Systems Using Flagellated Bacteria, " D. thesis, Brown University, Providence, RI.