Wear mechanism analysis in milling of Ti-6Al-4V alloy

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 227, Issue 8, 2013, Pages 1148-1156

  Jaffery, Syed Hi ^a   Khan, Mushtaq ^b   Sheikh, Nadeem A ^c   Mativenga, Paul ^b  

^a NATIONAL UNIVERSITY OF SCIENCES AND TECHNOLOGY   (Pakistan)

^b UNIVERSITY OF MANCHESTER   (United Kingdom)

^c CAPITAL UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Pakistan)

Author keywords

Built up edge; Cutting speed; Milling; Safety zone; Tool wear; Wear maps

Indexed keywords

BUILT UP EDGE; CUTTING SPEED; SAFETY ZONE; TOOL WEAR; WEAR MAPS;

ALUMINUM; CARBIDES; CUTTING; CUTTING TOOLS; MILLING (MACHINING); SCANNING ELECTRON MICROSCOPY; TITANIUM ALLOYS; TRIBOLOGY; X RAY ANALYSIS;

WEAR OF MATERIALS;

EID: 84884563858     PISSN: 09544054     EISSN: 20412975     Source Type: Journal    
DOI: 10.1177/0954405413481210     Document Type: Article

References (56)

1. Amin AKMN, Ismail AF and Khairusshima MKN. Effectiveness of uncoated WC-Co and PCD inserts in end milling of titanium alloy-Ti-6Al-4V. J Mater Process Tech 2007; 193: 147-158.
2. Waterman NA and Ashby MF. Elsevier material selector, vol. 2. Essex: CRC Press, 1991.
3. Hughes JI, Sharman A and Ridgway K. The effect of cutting tool material and edge geometry on tool life and workpiece surface integrity. Proc IMechE, Part B: J Engineering Manufacture 2006; 220: 93-107.
4. Jaffery SI and Mativenga PT. Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach. Int J Adv Manuf Tech 2009; 40: 687-696.
5. Teoh SH. Engineering materials for biomedical applications. Singapore: World Scientific Publishing Co. Pte. Ltd, 2004.
6. Hughes J, Sharman A and Ridgway K. The effect of tool edge preparation on tool life and workpiece surface integrity. Proc IMechE, Part B: J Engineering Manufacture 2004; 218(9): 1113-1123.
7. Boyer RR. An overview on the use of titanium in the aerospace industry. Mat Sci Eng A: Struct 1996; 213(1-2): 103-114.
8. Weiss V. Aerospace structural metals handbook, vol. 2. Syracuse, NY: Syracuse University, 1963.
9. Lopez de lacalle LN, Pérez J, Llorente JI, et al. Advanced cutting conditions for the milling of aeronautical alloys. J Mater Process Tech 2000; 100: 1-11.
10. Liu CY, Tang ZA, Yang S, et al. Machinability of ZTC4 titanium alloy analysis using finite element simulation and milling experiment. Key Eng Mat 2011; 474-476: 633-638.
11. Komanduri R and Reed JWR. Evaluation of carbide grades and a new cutting geometry for machining titanium alloys. Wear 1983; 92: 113-123.
12. Kramer BM, Viens D and Chin S. Theoretical consideration of rare earth metal compounds as tool materials for titanium machining. CIRP Ann: Manuf Techn 1993; 42(1): 111-114.
13. Ezugwu EO and Wang ZM. Titanium alloys and their machinability-a review. J Mater Process Tech 1997; 68: 262-274.
14. Narutaki N, Murakoshia A, Motonishib S, et al. Study on machining of titanium alloys. CIRP Ann: Manuf Techn 1983; 32(1): 65-69.
15. Ribeiro MV, Moreira MRV and Ferreira Jr. Optimization of titanium alloy (Ti-6Al-4V) machining. J Mater Process Tech 2003; 143-144: 458-463.
16. Jaffery SI and Mativenga PT. Wear mechanism analysis for turning Ti-6Al-4V-towards the development of suitable tool coatings. Int J Adv Manuf Tech 2012; 58(5-8): 479-493.
17. Shaw MC. Metal Cutting Principles. Tempe, AZ: Oxford University Press, 2005.
18. Cselle T and Barimani A. Today's applications and future developments of coatings for drills and rotating cutting tools. Surf Coat Tech 1995; 76-77(Part 2): 712-718.
19. Calamaz M, Nouari M, Géhin D, et al. Damage modes of straight tungsten carbide in dry machining of titanium alloy Ti-6Al-4V. J Phys IV 2006; 134: 1265-1271.
20. Ridgway K, Turner MS, Sharman ARC, et al. Machining aerospace materials: encyclopedia of aerospace engineering. John Wiley & Sons, (online), 2010.
21. Huang P, Li J, Sun J, et al.Milling force vibration analysis in high-speed-milling titanium alloy using variable pitch angle mill. Int J Adv Manuf Tech 2012; 58: 153-160.
22. Elmagrabi N, Hassan CH, Jaharah AG, et al. High speed milling of Ti-6Al-4V using coated carbide tools. Euro J Sci Res 2008; 22(2): 153-162.
23. Che Haron CH, Ginting A and Arshad H. Performance of alloyed uncoated and CVD-coated carbide tools in dry milling of titanium alloy Ti-6242S. J Mater Process Tech 2007; 185(1-3): 77-82.
24. Sharif S and Rahim EA. Performance of coated- and uncoated-carbide tools when drilling titanium alloy-Ti- 6Al4V. J Mater Process Tech 2007; 185(1-3): 72-76.
25. Ginting A and Nouari M. Experimental and numerical studies on the performance of alloyed carbide tool in dry milling of aerospace material. Int J Mach Tools Manu 2006; 46(7-8): 758-768.
26. Nouari M and Ginting A. Wear characteristics and performance of multilayer CVD-coated alloyed carbide tool in dry end milling of titanium alloy. Surf Coat Tech 2006; 200(18-19): 5663-5676.
27. Zareena AR, Rahman M and Wong YS. Binderless CBN tools, a breakthrough for machining titanium alloys. J Manuf Sci E: T ASME 2005; 127: 277-279.
28. Jawaid A, Che-Haron CH and Abdullah A. Tool wear characteristics in turning of titanium alloy Ti-6246. J Mater Process Tech 1999; 92-93: 329-334.
29. Beake BD, Smith JF, Gray A, et al. Investigating the correlation between nano-impact fracture resistance and hardness/modulus ratio from nanoindentation at 25-500 °C and the fracture resistance and lifetime of cutting tools with Ti1 2 xAlxN (x=0.5 and 0.67) PVD coatings in milling operations. Surf Coat Tech 2007; 201(8): 4585-4593.
30. Shi Q, Li L, He N, et al. Experimental study in high speed milling of titanium alloy TC21. Int J Adv Manuf Tech 2013; 64(1-4): 49-54.
31. Ginta TL and Amin AKMN. Cutting force and tool life models in end milling titanium alloy Ti-4Al-4V with thermally-assisted machining. Int J Mech Comput Manuf Res 2012; 1(1): 1-5.
32. Beranoagirre A, Olvera D and Ló pez de Lacalle LN. Milling of gamma titanium-aluminum alloys. Int J Adv Manuf Tech 2012; 62(1-4): 83-88.
33. Chen G, Ren C, Yang X, et al. Finite element simulation of high-speed machining of titanium alloy (Ti-6Al-4V) based on ductile failure model. Int J Adv Manuf Tech 2011; 4(1): 11-23.
34. Ueda T, Hosokawa A, Oda K, et al. Temperature on flank face of cutting tool in high speed milling. CIRP Ann: Manuf Techn 2001; 50(1): 37-40.
35. Abou-El-Hossein KA, Kadirgama K, Hamdi M, et al. Prediction of cutting force in end-milling operation of modified AISI P20 tool steel. J Mater Process Tech 2007; 182(1-3): 241-247.
36. Alauddin M, El Baradie MA and Hashmi MSJ. Computer- aided analysis of a surface-roughness model for end milling. J Mater Process Tech 1995; 55(2): 123-127.
37. Zhang S, Wu Y and Wang Y. An empirical surface roughness model of titanium alloys cut with abrasive water jet. Adv Mat Res 2011; 189-193: 4231-4244.
38. Jiang Z, Li S, Zeng J, et al. An empirical surface roughness model of titanium alloys cut with abrasive water jet. Adv Mater Res 2011; 189-193: 4231-4244.
39. Inspergera T, Mannb BPM, Stépán G, et al. Stability of up-milling and down-milling, part 1: alternative analytical methods. Int J Mach Tools Manu 2003; 43: 25-34.
40. Lim SC, Lee SH, Liu YB, et al. Wear maps for some uncoated cutting tools. Tribotest 1996; 3(1): 67-88.
41. Lim SC, Liua YB, Lee SH, et al. Mapping the wear of some cutting-tool materials. Wear 1993; 162-164: 971-974.
42. Lim SC, Lee SH, Liua YB, et al. Wear maps for uncoated high-speed steel cutting tools. Wear 1993; 170(1): 137-144.
43. Lim CYH, Lim SC and Lee KS. Wear of TiC-coated carbide tools in dry turning. Wear 1999; 225-229: 354-367.
44. Lim CYH, Lau PPT and Lim SC. The effects of work material on tool wear. Wear 2001; 250: 344-348.
45. Lim CYH, Lau PPT and Lim SC. Work material and the effectiveness of coated tools. Surf Coat Tech 2001; 146-147: 298-304.
46. Sun J and Guo YB. A new multi-view approach to characterize 3D chip morphology and properties in end milling titanium Ti-6Al-4V. Int J Mach Tools Manu 2008; 48(12-13): 1486-1494.
47. Zhang S and Li JF. Tool wear criterion integrated tool life and surface roughness requirement during high-speed end-milling Ti-6Al-4V alloy. J Zhejiang Univ: Sci A 2010; 11(8): 587-595.
48. Maekawa K, Obikawa T, Yamane Y, et al. Metal machining-theory and applications. New York: John Wiley & Sons, 2000.
49. ISO 8688-2:1989. Tool life testing in milling-part 2: end milling.
50. Stephenson DA and Agapiou JS. Metal cutting theory and practice. 2nd ed. CRC Press, Boca Raton Florida, USA. 2005.
51. Li HZ, Zeng H and Chen XQ. An experimental study of tool wear and cutting force variation in the end milling of Inconel 718 with coated carbide inserts. J Mater Process Tech 2006; 180(1-3): 296-304.
52. Bouzakis KD, Gerardis S, Katirtzoglou G, et al. Increasing tool life by adjusting the milling cutting conditions according to PVD films' properties. CIRP Ann: Manufacturing Technology 2008; 57(1): 105-108.
53. Jaffery SI and Mativenga PT. Study of the use of wear maps for assessing machining performance. Proc IMechE, Part B: J Engineering Manufacture 2009; 223(9): 1097-1105.
54. Nabhani F. Wear mechanisms of ultra-hard cutting tools materials. J Mater Process Tech 2001; 115(3): 402-412.
55. Pierson HO. Handbook of refractory carbides and nitrides. Westwood, NJ: William Andrew Publishing, 1996.
56. Cherukuri R and Molian P. Lathe turning of titanium using pulsed laser deposited, ultra-hard boride coatings of carbide inserts. Mach Sci Technol 2003; 7(1): 119-135.