A critical assessment of experimental methods for determining the dynamic mechanical characteristics of shape memory polymers

Advanced Engineering Materials

Volumn 15, Issue 8, 2013, Pages 732-739

  Kazakevičiute Makovska, Rasa ^a   Mogharebi, Safa ^a   Steeb, Holger ^a   Eggeler, Gunther ^a   Neuking, Klaus ^a  

^a RUHR UNIVERSITY BOCHUM   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

DYNAMIC MECHANICAL ANALYSIS (DMA); EXPERIMENTAL METHODS; EXPERIMENTAL STUDIES; FREQUENCY-DEPENDENT; SHAPE MEMORY POLYMERS; STORAGE AND LOSS MODULUS; TEMPERATURE DEPENDENT; THREE POINT BENDING;

BENDING TESTS; POLYMERS; SHAPE MEMORY EFFECT; TORSION TESTING; TORSIONAL STRESS;

BENDING (DEFORMATION);

EID: 84881127709     PISSN: 14381656     EISSN: 15272648     Source Type: Journal    
DOI: 10.1002/adem.201200341     Document Type: Article

References (35)

1. K. P. Menard, Dynamic Mechanical Analysis: A Practical Introduction, CRC Press, Washington, D.C. 1999.
2. E. A. Turi, Thermal Characterization of Polymeric Materials, Vol. I, Academic Press, New York 1997.
3. R. E. Wetton, Polym. Test. 1984, 4, 117.
4. J. M. Hutchinson, J. Therm. Anal. Calorim. 2009, 98, 579.
5. J. F. Gerard, S. J. Andrews, C. W. Macosko, Polym. Compos. 1990, 11, 90.
6. M. Opliger, Technical Review, National Institute for Aviation Research, Wichita State University, USA 2012.
7. G. D. Sims, S. J. P. Gnaniah, Presented at the 17th Int. Conf. on Composite Materials, Edinburg, Scotland, July 2009.
8. C. A. Gracia-Fernández, S. Gõmez-Barreiro, J. Lõpez-Beceiro, J. Tarrío Saavedra, S. Naya, R. Artiaga, Polym. Test. 2010, 29, 1002.
9. W. Wagermaier, K. Kratz, M. Heuchel, A. Lendlein, Adv. Polym. Sci. 2010, 226, 97.
10. M. Heuchel, J. Cui, K. Kratz, H. Kosmella, A. Lendlein, Polym. 2010, 51, 6212.
11. C. Schmidt, Ph. D. Thesis, Ruhr University Bochum, Germany 2011.
12. C. Schmidt, A. M. Sarwaruddin Chowdhury, K. Neuking, G. Eggeler, J. Macromol. Sci. Part A 2011, 48, 204.
13. J. Klesa, presented at the STC (Studentské Tvůrci Činnosti) Conf, Prague, Czech, March 2009.
14. K. Gall, C. M. Yakacki, Y. Liu, R. Shandas, N. Willett, K. S. Anseth, J. Biomed. Mater. Res. Part A 2005, 73, 339.
15. A. J. W. McClung, G. P. Tandon, J. W. Baur, Mech. Time-Depend. Mater. 2012, 16, 205.
16. F. Castro, K. K. Westbrook, J. Hermiller, D. U. Ahn, Y. Ding, H. J. Qi, J. Eng. Mater. Technol. 2011, 133, 021025.
17. P. T. Mather, X. Luo, I. A. Rousseau, Annu. Rev. Mater. Res. 2009, 39, 445.
18. D. Ratna, J. Karger-Kocsis, J. Mater. Sci. 2008, 43, 254.
19. S. Deng, M. Hou, L. Ye, Polym. Test. 2007, 26, 803.
20. P. Lee-Sullivan, D. Dykeman, Polym. Test. 2000, 19, 155.
21. S. Qing, P. Lee-Sullivan, Polym. Test. 2000, 19, 239.
22. G. Swaminathan, K. Shivakumar, J. Reinf. Plast. Compos. 2009, 28, 979.
23. A. R. Wedgewood, J. C. Seferis, Polymer 1981, 22, 966.
24. J. Hättig, J. Winkler, PU Mag. 2008, 16, 199.
25. Processing Information, Noveon, Raubling, Germany 2003.
26. TPU-Verarbeitungsparameter Spritzguss, Huntsman, Osnabrück, Germany 2007.
27. Verarbeitungsdaten-für den Spritzgießer, Bayer Material Science, Leverkusen, Germany 2005.
28. E. Bürkle, D. Ammer, M. Würtele, in Medizintechnik: Life Science Engineering (Eds:, E. Wintermantel, S.-W. Ha,), Springer, Heidelberg 2009, Ch. 26.
29. Einführung in das Spritzgießen, Arburg, Lossburg, Germany 2004.
30. Fehlerfrei Spritzgießen-Tipps für TPUs, Bayer Material Science, Leverkusen, Germany 2007.
31. Betriebsanleitung für EPLEXOR, Gabo Qualimeter®, Ahlden, Germany 2011.
32. Betriebsanleitung für EPLEXOR, Gabo Qualimeter®, Ahlden, Germany 2008.
33. Physica MCR, Anton Paar, Ostfildern, Germany 2006.
34. Rheoplus Software (3.0×), Anton Paar, Ostfildern, Germany 2006.
35. E. Sideridis, I. N. Prassianakis, V. N. Kytopoulos, J. Appl. Polym. Sci. 2006, 101, 3869.