Effect of cracks and pitting defects on gear meshing

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science

Volumn 226, Issue 11, 2012, Pages 2805-2815

  Del Rincon, Alfonso Fernandez ^a   Viadero, Fernando ^a   Iglesias, Miguel ^a   De Juan, Ana ^a   Garcia, Pablo ^a   Sancibrian, Ramon ^a  

^a UNIVERSITY OF CANTABRIA   (Spain)

Author keywords

crack; finite element; load ratio; meshing stiffness; pitting; spur gear; Transmission error

Indexed keywords

FINITE ELEMENT; FINITE ELEMENT MODELS; FUNDAMENTAL FREQUENCIES; LOAD RATIO; MESHING STIFFNESS; MONITORING TECHNIQUES; NONLINEAR EQUATION SYSTEM; TRANSMISSION ERROR;

CONDITION MONITORING; CONSTRAINT THEORY; FINITE ELEMENT METHOD; LINEAR EQUATIONS; PITTING; SPUR GEARS; STIFFNESS; VIBRATION ANALYSIS;

CRACKS;

EID: 84874806922     PISSN: 09544062     EISSN: 20412983     Source Type: Journal    
DOI: 10.1177/0954406212437104     Document Type: Article

References (21)

1. Heng A, Zhang S, Tan ACC, et al. Rotating machinery prognostics: state of the art, challenges and opportunities. Mech Syst Sig Process. 2009 ; 23 (3). 724-739
2. Parey A, Tandon N. Spur gear dynamic models including defects: a review. Shock Vib Dig. 2003 ; 35 (6). 465-478
3. Randall RB. A new method of modeling gear faults. Trans ASME J Mech Des. 1982 ; 104: 259-267
4. Özgüven HN, Houser DR. Mathematical models used in gear dynamics - a review. J Sound Vib. 1988 ; 121 (3). 383-411 (Pubitemid 18603605)
5. Kahraman A. Effect of axial vibrations on the dynamics of a helical gear pair. J Vib Acoust Stress Reliab Des. 1993 ; 115 (1). 33-39 (Pubitemid 23609963)
6. Peeters J. Simulation of dynamic drive train loads in a wind turbine. PhD Thesis, Katholieke Universiteit Leuven, Belgium, 2006.
7. Cai Y, Hayashi T. Linear approximated equation of vibration of a pair of spur gears (theory and experiment). Trans ASME J Mech Des. 1994 ; 116 (2). 558-564
8. Howard I, Jia S, Wang J. The dynamic modelling of a spur gear in mesh including friction and a crack. Mech Syst Sig Process. 2001 ; 15 (5). 831-853 (Pubitemid 33112615)
9. Wang J, Howard I. The torsional stiffness of involute spur gears. Proc Inst Mech Eng Part C J Mech Eng Sci. 2004 ; 218 (1). 131-142 (Pubitemid 38259001)
10. Vedmar L, Andersson A. A method to determine dynamic loads on spur gear teeth and on bearings. J Sound Vib. 2003 ; 267 (5). 1065-1084
11. Parker RG, Vijayakar SM, Imajo T. Non-linear dynamic response of a spur gear pair: modelling and experimental comparisons. J Sound Vib. 2000 ; 237 (3). 435-455
12. Parey A, El Badaoui M, Guillet F, et al. Dynamic modelling of spur gear pair and application of empirical mode decomposition-based statistical analysis for early detection of localized tooth defect. J Sound Vib. 2006 ; 294 (3). 547-561 (Pubitemid 44262248)
13. Saryazdi MG, Durali M. The effect of three-dimensional crack growth on the force distribution and meshing stiffness of a spur gear: ideal and misaligned contacts. Proc Inst Mech Eng Part C J Mech Eng Sci. 2009 ; 223 (7). 1633-1644
14. Jia S, Howard I. Comparison of localised spalling and crack damage from dynamic modelling of spur gear vibrations. Mech Syst Sig Process. 2006 ; 20 (2). 332-349 (Pubitemid 41606172)
15. Endo H, Randall RB, Gosselin C. Differential diagnosis of spall versus cracks in the gear tooth fillet region. J Fail Anal Prev. 2004 ; 4 (5). 63-71 (Pubitemid 40134522)
16. Zouari S, Maatar M, Fakhfakh T, et al. Three-dimensional analyses by finite element method of a spur gear: effect of cracks in the teeth foot on the mesh stiffness. J Fail Anal Prev. 2007 ; 7 (6). 475-481
17. Chaari F, Fakhfakh T, Haddar M. Analytical modelling of spur gear tooth crack and influence on gearmesh stiffness. Eur J Mech A Solids. 2009 ; 28 (3). 461-468
18. Chaari F, Baccar W, Abbes MS, et al. Effect of spalling or tooth breakage on gearmesh stiffness and dynamic response of a one-stage spur gear transmission. Eur J Mech A Solids. 2008 ; 27 (4). 691-705
19. Shengxiang J, Ian H, Jiande W. The dynamic modeling of multiple pairs of spur gears in mesh, including friction and geometrical errors. Int J Rotating Mach. 2003 ; 9 (6). 437-442
20. Liu L, Pines DJ. The influence of gear design parameters on gear tooth damage detection sensitivity. Trans ASME J Mech Des. 2002 ; 124 (4). 794-804
21. Atanasovska I, Mitrović R, Momčilović D, et al. Analysis of the nominal load effects on gear load capacity using the finite-element method. Proc Inst Mech Eng Part C J Mech Eng Sci. 2010 ; 224 (11). 2539-2548