Generation of reciprocating tool motion in 5-axis flank milling based on particle swarm optimization

Journal of Intelligent Manufacturing

Volumn 23, Issue 5, 2012, Pages 1501-1509

  Chu, Chih Hsing ^a   Hsieh, Hsin Ta ^a  

^a NATIONAL TSING HUA UNIVERSITY   (Taiwan)

Author keywords

Five axis machining; Flank milling; Particle swarm optimization; Tool path planning

Indexed keywords

CUTTING EXPERIMENT; FIVE-AXIS MACHINING; FLANK MILLING; GEOMETRIC PROBLEMS; MACHINED SURFACE; MACHINING ERROR; OBJECTIVE FUNCTIONS; PLANNING METHOD; RULED SURFACES; TOOL PATH GENERATION; TOOL PATH PLANNING; TOOLPATHS;

MATHEMATICAL PROGRAMMING; MOTION PLANNING; PARTICLE SWARM OPTIMIZATION (PSO); SCANNING;

MILLING (MACHINING);

EID: 84870892050     PISSN: 09565515     EISSN: 15728145     Source Type: Journal    
DOI: 10.1007/s10845-010-0450-z     Document Type: Article

References (16)

1. Altan, T., Lilly, B. W., Kruth, J. P., Konig, W., Tonshoff, H. K., & Khairy, A. B. (1993). Advanced techniques for die and mold manufacturing. CIRP Annals, 42(1), 707-716.
2. Baskar, N., Asokan, P., Prabhaharan, G., & Saravanan, R. (2005). Optimization ofmachining parameters for milling operations using non-conventional methods. International Journal of Advanced Manufacturing Technology, 25(11-12), 1078-1088.
3. Bedi, S., Mann, S., & Menzel, C. (2003). Flank milling with flat end milling cutters. Computer Aided Design, 35, 293-300.
4. Bohez, E. L. J., Senadhera, S. D. R., Pole, K., Duflou, J. R., & Tar, T. (1997). A geometric modeling and five-axis machining algorithm for centrifugal impellers. Journal of Manufacturing Systems, 16(6), 436.
5. Budak, E., Ozturk, E., & Tunc, L. T. (2009). Modeling and simulation of 5-axis milling processes. CIRP Annals, 58(1), 347-350.
6. Chan, F. T. S., & Tiwari, M. K. (2007). Swarm intelligence, focus on ant and particle swarm optimization. Vienna, Austria: I-Tech Education and Publishing.
7. Kennedy, J., & Eberhart, R. C. (1995). Particle swarm optimization. In Proceedings of IEEE international conference on neural networks (Perth, Australia). Piscataway, NJ: IEEE Service Center IV:1942-1948.
8. Kersting, P., & Zabel, A. (2009). Optimizing NC tool paths for simultaneous five-axis milling based on multi-population multi-objective evolutionary algorithms (Vol. 40, pp. 452-463).
9. Lartigue, C., Duc, E., & Affouard, A. (2003). Tool path deformation in 5-axis flank milling using envelop surface. Computer-Aided Design, 35, 375-382.
10. Liu, X. W. (1995). Five-axis NC cylindrical milling of sculptured surfaces. Computer-Aided Design, 27(12), 887-894.
11. Menzel, C., Bedi, S., & Mann, S. (2004). Triple tangent flank milling of ruled surfaces. Computer-Aided Design, 36, 289-296.
12. Poli, R., Kennedy, J., & Blackwell, T. (2007). Particle swarm optimization: An overview. Swarm Intelligence, 1, 33-57.
13. Rehsteiner, F. (1993). Collision-free five-axis milling of twisted ruled surfaces. CIRP Annals, 42(1), 457-461.
14. Tandon, V., El-Mounayri, H., & Kishawy, H. (2002). NC End Milling Optimization using Evolutionary Computation. International Journal of Machine Tools & Manufacture, 42(5), 595-605.
15. Tsay, D. M., & Her, M. J. (2001). Accurate 5-axis machining of twisted ruled surfaces. ASME Journal of Manufacturing Science and Engineering, 123, 731-738.
16. Wu, P. H., Li, Y. W., & Chu, C. H. (2008). Optimized tool path generation based on dynamic programming for five-axis flank milling of rule surface. International Journal of Machine Tools & Manufacture, 48(11), 1224-1233.