Optimized tool path generation based on dynamic programming for five-axis flank milling of rule surface

International Journal of Machine Tools and Manufacture

Volumn 48, Issue 11, 2008, Pages 1224-1233

  Wu, Ping Han ^a   Li, Yu Wei ^a   Chu, Chih Hsing ^a  

^a NATIONAL TSING HUA UNIVERSITY   (Taiwan)

Author keywords

Dynamic programming; Five axis machining; Flank milling; Optimization; Ruled surface

Indexed keywords

DYNAMIC PROGRAMMING; ERROR CORRECTION; OPTIMIZATION; QUALITY CONTROL;

FIVE-AXIS MACHINING; FLANK MILLING;

MACHINING;

EID: 44649148875     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2008.03.009     Document Type: Article

References (15)

1. Vickers G.B., and Guan K.W. Ball-mills versus end-mills for curved surface machining. ASME Journal of Engineering for Industry 111 (1989) 22-26
2. Wu C.Y. Arbitrary surface flank milling of fan, compressor, and impeller blades. Transactions of ASME Journal of Engineering for Gas Turbines and Power 117 3 (1995) 534-539
3. Choi B.K., Park J.W., and Jun C.S. Cutter-location data optimization in 5-axis surface machining. Computer-Aided Design 25 6 (1993) 377-386
4. Li S.X., and Jerard R.B. Five-axis machining of sculptured surfaces with a flat-end cutter. Computer-Aided Design 26 3 (1994) 165-178
5. Lee Y.S. Admissible tool orientation control of gouging avoidance for 5-axis complex surface machining. Computer-Aided Design 29 7 (1997) 507-521
6. You C.F., and Chu C.H. Tool-path verification in five-axis machining of sculptured surfaces. International Journal of Advanced Manufacturing Technology 13 4 (1997) 248-255
7. Chu C.H., and Chen J.T. Automatic tool path generation for 5-axis flank milling based on developable surface approximation. International Journal of Advanced Manufacturing Technology 29 7-8 (2006) 707-713
8. Liu X.W. Five-axis NC cylindrical milling of sculptured surfaces. Computer-Aided Design 27 12 (1995) 87-94
9. Bohez E.L.J., Ranjith Senadhera S.D., Pole K., Duflou J.R., and Tar T. A geometric modeling and five-axis machining algorithm for centrifugal impellers. Journal of Manufacturing Systems 16 6 (1997) 422-436
10. Lartigue C., Duc E., and Affouard A. Tool path deformation in 5-axis flank milling using envelope surface. Computer-Aided Design 35 (2003) 375-382
11. Tsay D.M., and Her M.J. Accurate 5-axis machining of twisted ruled surfaces. ASME Journal of Manufacturing Science and Engineering 123 (2001) 731-738
12. Tsay D.M., Chen H.C., and Her M.J. A study on five-axis flank machining of centrifugal compressor impellers. ASME Journal of Engineering for Gas Turbines and Power 124 (2002) 177-181
13. Bedi S., Mann S., and Menzel C. Flank milling with flat end milling cutters. Computer-Aided Design 35 (2003) 293-300
14. Menzel C., Bedi S., and Mann S. Triple tangent flank milling of ruled surfaces. Computer-Aided Design 36 (2004) 289-296
15. Larue A., and Anselmetti B. Deviation of a machined surface in flank milling. International Journal of Machine Tools and Manufacture 43 2 (2003) 129-139