메뉴 건너뛰기




Volumn 36, Issue 3, 2004, Pages 289-296

Triple tangent flank milling of ruled surfaces

Author keywords

Five axis machining; Flank milling; Machine simulation; Tool path generation

Indexed keywords

ALGORITHMS; COMPUTER SIMULATION; IMPELLERS; MILLING (MACHINING); SURFACE TREATMENT; TURBOMACHINE BLADES;

EID: 0344494484     PISSN: 00104485     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0010-4485(03)00118-0     Document Type: Article
Times cited : (89)

References (11)
  • 1
    • 0037332657 scopus 로고    scopus 로고
    • Flank milling with flat end cutters
    • Bedi S., Mann S., Menzel C. Flank milling with flat end cutters. Comput Aided Des. 35:2003;293-300.
    • (2003) Comput Aided Des , vol.35 , pp. 293-300
    • Bedi, S.1    Mann, S.2    Menzel, C.3
  • 2
    • 0001131196 scopus 로고    scopus 로고
    • A geometric modeling and five-axis machining algorithm for centrifugal impellers
    • Bohez E.L.J., Senadhera S.D.R., Pole K., Duflou J.R., Tar T. A geometric modeling and five-axis machining algorithm for centrifugal impellers. J Manuf Syst. 16:(6):1997;422-463.
    • (1997) J Manuf Syst , vol.16 , Issue.6 , pp. 422-463
    • Bohez, E.L.J.1    Senadhera, S.D.R.2    Pole, K.3    Duflou, J.R.4    Tar, T.5
  • 3
    • 0029196329 scopus 로고
    • Five-axis NC cylindrical milling of sculptured surfaces
    • Liu X.W. Five-axis NC cylindrical milling of sculptured surfaces. Comput Aided Des. 27:(12):1995;887-894.
    • (1995) Comput Aided Des , vol.27 , Issue.12 , pp. 887-894
    • Liu, X.W.1
  • 4
    • 0031630343 scopus 로고    scopus 로고
    • Side milling of ruled surfaces: Optimum positioning of the milling cutter and calculation of interference
    • Redonnet J.-M., Rubio W., Dessein G. Side milling of ruled surfaces: optimum positioning of the milling cutter and calculation of interference. Int J Adv Manuf Technol. 14:1998;459-465.
    • (1998) Int J Adv Manuf Technol , vol.14 , pp. 459-465
    • Redonnet, J.-M.1    Rubio, W.2    Dessein, G.3
  • 5
    • 0027269199 scopus 로고
    • Collision free five axis milling of twisted ruled surfaces
    • Rehsteiner F., Renker H.J. Collision free five axis milling of twisted ruled surfaces. Ann CIRP. 42:(1):1993;267-271.
    • (1993) Ann CIRP , vol.42 , Issue.1 , pp. 267-271
    • Rehsteiner, F.1    Renker, H.J.2
  • 7
    • 0000838687 scopus 로고
    • Arbitrary surface flank milling of fan, compressor, and impeller blades
    • Wu C.W. Arbitrary surface flank milling of fan, compressor, and impeller blades. J Engng Gas Turbines Power. 117:1995;534-539.
    • (1995) J Engng Gas Turbines Power , vol.117 , pp. 534-539
    • Wu, C.W.1
  • 8
    • 0000227131 scopus 로고    scopus 로고
    • Accurate 5-axis machining of twisted ruled surfaces
    • Tsay D.M., Her M.J. Accurate 5-axis machining of twisted ruled surfaces. J Manuf Sci Engng. 123:2001;731-738.
    • (2001) J Manuf Sci Engng , vol.123 , pp. 731-738
    • Tsay, D.M.1    Her, M.J.2
  • 9
    • 0032119927 scopus 로고    scopus 로고
    • Swept volumes of toroidal cutters using generating curves
    • Sheltami K., Bedi S., Ismail F. Swept volumes of toroidal cutters using generating curves. Int J Machine Tools Manuf. 38:1998;855-870.
    • (1998) Int J Machine Tools Manuf , vol.38 , pp. 855-870
    • Sheltami, K.1    Bedi, S.2    Ismail, F.3
  • 10
    • 0035147913 scopus 로고    scopus 로고
    • Surface swept by a toroidal cutter during 5-axis machining
    • Roth D., Bedi S., Ismail F., Mann S. Surface swept by a toroidal cutter during 5-axis machining. Comput Aided Des. 33:(1):2001;57-63.
    • (2001) Comput Aided Des , vol.33 , Issue.1 , pp. 57-63
    • Roth, D.1    Bedi, S.2    Ismail, F.3    Mann, S.4


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.