Utilising friction spot joining for dissimilar joint between aluminium alloy (A5052) and polyethylene terephthalate

Science and Technology of Welding and Joining

Volumn 17, Issue 7, 2012, Pages 544-549

  Yusof, F ^a   Miyashita, Y ^b   Seo, N ^c   Mutoh, Y ^b   Moshwan, R ^a  

^a UNIVERSITY OF MALAYA   (Malaysia)

^b NAGAOKA UNIVERSITY OF TECHNOLOGY   (Japan)

^c Nippon Light Metal Company Ltd   (Japan)

Author keywords

Aluminium alloy; Bubble formation; Dissimilar materials; Friction spot joining; Thermoplastic

Indexed keywords

DISSIMILAR JOINTS; FRICTION SPOT JOINING; FRICTION STIR; FRICTIONAL HEAT; POLYPROPYLENE SHEETS; SHEAR STRENGTH OF JOINT; SPINDLE SPEED; SPOT-WELDING PROCESS; WELD STRENGTH;

ALUMINUM ALLOYS; BUBBLE FORMATION; DISSIMILAR MATERIALS; FRICTION; FRICTION STIR WELDING; MECHANICAL PROPERTIES; REINFORCED PLASTICS; SPOT WELDING; THERMOPLASTICS;

POLYETHYLENE TEREPHTHALATES;

EID: 84867085731     PISSN: 13621718     EISSN: 17432936     Source Type: Journal    
DOI: 10.1179/136217112x13408696326530     Document Type: Article

References (29)

1. P. H. F Oliveira, S. T. Amancio-Filho, J. F. Dos Santos and E. Hage, Jr: 'Preliminary study on the feasibility of friction spot welding in PMMA', Mater. Lett., 2010, 64, 2098-2101.
2. D. M. Rodrigues, A. Loureiro, C. Leitao, R. M. Leal, B. M. Chaparro and P. Vilaça: 'Influence of friction stir welding parameters on the microstructural and mechanical properties of AA 6016-T4 thin welds', Mater. Des., 2009, 30, 1913-1921.
3. A. H. Feng, B. L. Xiao and Z. Y. Ma: 'Grain boundary misorientation and texture development in friction stir welded SiCp/Al-Cu-Mg composite', Mater. Sci. Eng. A, 2008, A497, (1-2), 515-518.
4. G. Ç am: 'Friction stir welded structural materials beyond Alalloys', Int. Mater. Rev., 2011, 56, (1), 1-48.
5. R. M. Leal, C. Leitão, A. Loureiro, D.M. Rodrigues and P. Vilaça: 'Material flow in heterogeneous friction stir welding of thin aluminum sheets: effect of shoulder geometry', Mater. Sci. Eng. A, 2008, A498, 384-391.
6. M. Ghosh, K. Kumar, S. V. Kailas and A. K. Ray: 'Optimization of friction stir welding parameters for dissimilar aluminum alloys', Mater. Des., 2010, 31, 3033-3037.
7. E. Cerri and P. Leo: 'Warm and room temperature deformation of friction stir welded thin aluminium sheets', Mater. Des., 2010, 31, 1392-1340.
8. K. Colligan: 'Materials flow behavior during friction stir welding of aluminum', Weld. Res. Suppl., 1999, 78, (7), 229-237.
9. L. E. Murr, G. Liu and J. C. McClure: 'Dynamic recrystallization in friction stir welding of aluminum alloy 1100', J Mater. Sci. Lett., 1997, 16, 1801-1803.
10. R. Nandan, T. DebRoy and H. K. D. H. Bhadeshia: 'Recent advances in friction-stir welding-process, weldment structure and properties', Prog. Mater. Sci., 2008, 53, 980-1023.
11. H. Fujii, N. Takaki and Y. Okitsu: 'Novel spot friction stir welding of 6061 & 5052 Al alloys', Sci. Technol. Weld. Join., 2011, 16, (7), 605-612.
12. K. Sovolainen, T. Saukkonen and H. Hanninen: 'Banding in copper friction stir weld', Sci. Technol. Weld. Join., 2012, 17, (2), 111-115.
13. T. Sakthivel and J. Mukhpadhyay: 'Microstructure and mechanical properties of friction stir welded copper', J Mater. Sci., 2007, 42, (19), 8126-8129.
14. A. J. Ramirez and M. C. Juhas: 'Microstructural evolution in Ti-6Al-4V friction stir welds', Mater. Sci. Forum, 2003, 426-432, 2999-3004.
15. H. Liu, K. Nakata, N. Yamamoto and J. Liao: 'Friction stir welding of pure titanium lap joint', Sci. Technol. Weld. Join., 2010, 15, (5), 428-432.
16. Y. S. Sato, T. W. Nelson, C. J. Sterling, R. J. Steel and C. O. Pettersson: 'Microstructure and mechanical properties of friction stir welded SAF 2507 super duplex stainless steel', Mater. Sci. Eng. A, 2005, A397, (1-2), 376-384.
17. L. Commin, M. Dumont, J. E. Masse and L. Barrallier: 'Friction stir welding of AZ31 magnesium alloy rolled sheets: influence of processing parameters', Acta Mater., 2009, 57, (2), 326-334.
18. H. Nami, H. Adgi, M. Sharifitabar and H. Shamabadi: 'Microstructure and mechanical properties of friction stir welded Al/Mg2Si metal matrix cast composite', Mater. Des., 2011, 32, 976-983.
19. S. T. A. Filho, C. Bueno, J. F. Santos, N. Huber and F. Hage: 'On the feasibility of friction spot joining in magnesium/fiber reinforced polymer composite hybrid structures', Mater. Sci. Eng. A, 2011, A528, 3841-3848.
20. S. Mert and A. Arici: 'Design of optimal joining for friction stir spot welding of polypropylene sheets', Sci. Technol. Weld. Join., 2011, 16, (6), 522-527.
21. A. Arici and T. Si{dotless}nmaz: 'Effects of double passes of the tool on friction stir welding of polyethylene', J. Mater. Sci., 2005, 40, 3313-3316.
22. M. K. Bilici, A. I. Yukler and M. Kurtulmus: 'The optimization of welding parameters for friction stir spot welding of high density polyethylene sheets', Mater. Des., 2011, 32, 4074-4079.
23. A. Arici and S. Mert: 'Friction stir spot welding of polypropylene', J. Reinf. Plast. Compos., 2008, 27, 2001-2004.
24. A. Mokhtar and V. H. Mucino: 'Energy generation during friction stir spot welding (FSSW) of Al 6061-T6 plates', Mater. Manuf. Processes, 2010, 25, (1), 167-174.
25. M. K. Bilici and A. I. Yukler: 'Effects of welding parameters on friction stir spot welding of high density polyethylene sheets', Mater. Des., 2012, 33, 545-550.
26. S. Katayama and Y. Kawahito: 'Laser direct joining of metal and plastic', Scr. Mater., 2008, 59, (12), 1247-1250.
27. M. Wahba, Y. Kawahito and S. Katayama: 'Laser direct joining of AZ91D thixomolded Mg alloy and amorphous polyethylene terephthalate', J. Mater. Process. Technol., 2011, 211, 1166-1174.
28. Y. Farazila, Y. Miyashita, W. Hua, Y. Mutoh and Y. Otsuka: 'YAG laser spot welding of PET and metallic materials', J. Laser Micro/Nanoeng., 2011, 6, 69-74.
29. Y. Farazila, Y. Miyashita, Y. Mutoh and A. S. Mohd Hamdi: 'Effect of anodizing on pulsed Nd:YAG laser joining of polyethylene terephthalate (PET) and aluminium alloy (A5052)', Mater. Des., 2012, 37, 410-415.