Estimation of milling tool temperature considering coolant and wear

Journal of Manufacturing Science and Engineering

Volumn 134, Issue 3, 2012, Pages

  Kuo, Hsin Yu ^a   Meyer, Kevin ^b   Lindle, Roger ^b   Ni, Jun ^a  

^a UNIVERSITY OF MICHIGAN   (United States)

^b GE AVIATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

HEAT GENERATION; MILLING (MACHINING); WEAR OF MATERIALS;

CUTTING FORCES; DEVELOPED MODEL; FLANK SURFACES; MACHINING PROCESS; NOVEL TECHNIQUES; TEMPERATURE CHANGES; TEMPERATURE RISE; TIME-DEPENDENT HEAT FLUX;

HEAT FLUX;

EID: 84860461686     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4005799     Document Type: Article

References (30)

1. Da Silva, M. B., and Wallbank, J., 1999, "Cutting Temperature: Prediction and Measurement Methods-A Review," J. Mater. Process. Technol., 88(1), pp. 195-202.
2. Komanduri, R., and Hou, Z. B., 2000, "Thermal Modeling of the Metal Cutting Process Part I-Temperature Rise Distribution due to Shear Plane Heat Source," Int. J. Mech. Sci., 42, pp.1715-1752.
3. Komanduri, R., and Hou, Z. B., 2000, "Thermal Modeling of the Metal Cutting Process Part II-Temperature Rise Distribution due to Frictional Heat Source at the Tool-Chip Interface," Int. J. Mech. Sci., 43, pp. 57-88. (Pubitemid 33375908)
4. Abukhshim, N. A., Mativenga, P. T., and Sheikh, M. A., 2006, "Heat Generation and Temperature Prediction in Metal Cutting: A Review and Implications for High Speed Machining," Int. J. Mach. Tools Manuf., 46(7-8), pp. 782-800.
5. Okushim, K., and Hoshi, T., 1963, "Thermal Crack in Carbide Face-Milling Cutter-2nd Report. Its Significance as Cause of Tool Failures," Bull. JSME, 6(22), pp. 317-326
6. Bhatia, S. M., Pandey, P. C., and Shan, H. S., 1980, "The Thermal Condition of the Tool Cutting Edge in Intermittent Cutting," Wear, 61, pp. 21-30. (Pubitemid 11443565)
7. Wu, H., and Mayer, J. E., 1979, "Analysis of Thermal Cracking of Carbide Tools in Intermittent," ASME J. Eng. Ind., 101(2), pp. 159-164. (Pubitemid 10445498)
8. Chakraverti, G., Pandey, P. C., and Mehta, N. K., "Analysis of Tool Temperature Fluctuation in Interrupted Cutting," Precis. Eng., 6(2), pp. 99-105.
9. Stephenson, D. A., and Ali, A., 1992, "Tool Temperature in Interrupted Metal Cutting," ASME. J. Eng. Ind., 114, pp. 127-136.
10. Radulescu, R., and Kapoor, S. G., 1994, "An Analytical Model for Prediction of Tool Temperature Fields During Continuous and Interrupted Cutting," ASME. J. Eng. Ind., 116(2), pp. 135-143.
11. Lazoglu, I., and Altintas, Y., 2002, "Prediction of Tool and Chip Temperature in Continuous and Interrupted Machining," Int. J. Mach. Tools Manuf., 42, pp. 1011-1022. (Pubitemid 34771992)
12. Dawson, P. R., and Malkin, S., 1984, "Inclined Moving Heat Source Model for Calculating Metal Cutting Temperatures," ASME. J. Eng. Ind., 106, pp. 179-186. (Pubitemid 14648546)
13. Childs, T. H. C., Maekawa, K., and Maulik, P., 1988, "Effects of Coolant on Temperature Distribution in Metal Machining," Mater. Sci. Technol., 4, pp. 1006-1019.
14. Berliner, E. M., and Krainov, V. P., 1991, "Analytical Calculations of the Temperature Field and Heat Flows on the Tool Surface in Metal Cutting due to Sliding Friction," Wear, 143, pp. 379-395.
15. Li, X., 1996, "Study of Jet-Flow Rate of Cooling in Machining Part 1. Theoretical Analysis," J. Mater. Process. Technol., 62, pp. 149-156. (Pubitemid 126365896)
16. Li, X., 1996, "Study of Jet-Flow Rate of Cooling in Machining Part 2. Simulation Study," J. Mater. Process. Technol., 62, pp. 157-165. (Pubitemid 126365897)
17. Kline, W. A., eVor, R. E., and Lindberg, J. R., 1982, "The Prediction of Cutting Forces in End Milling With Application to Cornering Cuts," Int. Mach. Tool Des. Res., 22(1), pp. 7-22. (Pubitemid 12523499)
18. Lee, P., and Altintas, Y., 1996, "Prediction of Ball-End Milling Forces From Orthogonal Cutting Data," Int. J. Mach. Tools Manuf., 36(9), pp. 684-692.
19. Shatla, M., and Altan, T., 2000, "Analytical Modeling of Drilling and Ball End Milling," J. Mater. Process. Technol., 98, pp. 125-133. (Pubitemid 30530250)
20. Bono, M., and Ni, J., 2006, "The Location of the Maximum Temperature on the Cutting Edges of a Drill," Int. J. Mach. Tools Manuf., 46, pp. 901-907.
21. Chandrasekharan, V., Kapoor, S. G., and DeVor, R. E., 1995, "Mechanistic Approach to Predicting the Cutting Forces in Drilling: With Application to Fiber-Reinforced Composite Materials," ASME J. Eng. Ind., 117(4), pp. 559-570.
22. Merchant, M. E., 1944, "Basic Mechanics of the Metal Cutting Process," ASME J. Appl. Mech. , 11(3), pp. A-168-A-175.
23. Loewen, E. G., and Shaw, M. C., 1954, "On the Analysis of the Cutting-Tool Temperatures," Trans. ASME, 76, pp. 217-231.
24. Smithey, D. W., Kapoor, S. G., and DeVor, R. E., 2000, "A Worn Tool Force Model for Three-Dimensional Cutting Operations," Int. J. Mach. Tools Manuf., 40, pp. 1929-1950.
25. Holman, J. P., 1992, Heat Transfer, McGraw-Hill, New York.
26. Meyer, K., 2007, "Milling Tool Performance Analysis in High Speed Milling of Titanium Alloys," Master thesis, University of Michigan, Ann Arbor, MI.
27. Smart, E. F., and Trent, E. M., 1975, "Temperature Distribution in Tools Used for Cutting Iron, Titanium and Nickel," Int. J. Prod. Res., 13(3), pp. 265-290.
28. Bono, M., and Ni, J., 2002, "A Method for Measuring the Temperature Distribution Along the Cutting Edges of a Drill," ASME. J. Manuf. Sci. Eng., 124, pp. 921-923. (Pubitemid 35384311)
29. Stephenson, D. A., 1991, "Assessment of Steady-State Metal Cutting Temperature Models Based on Simultaneous Infrared and Thermocouple Data," ASME J. Eng. Ind., 113, pp. 121-128. (Pubitemid 21669756)
30. Agaiou, J. S., and Stephenson, D. A., 1994, "Analytical and Experimental Studies of Drill Temperature," Trans. ASME, 116, pp. 54-60.