Virtual prototyping of a spraying robotic system

Environmental Engineering and Management Journal

Volumn 10, Issue 8, 2011, Pages 1197-1205

  Enescu, Monica ^a   Alexandru, Cǎtǎlin ^a  

^a TRANSILVANIA UNIVERSITY OF BRASOV   (Romania)

Author keywords

Control loop; Multi body system; Robotic system; Spray pyrolysis; Virtual prototype

Indexed keywords

EID: 84855462582     PISSN: 15829596     EISSN: None     Source Type: Journal    
DOI: 10.30638/eemj.2011.172     Document Type: Article

References (17)

1. Alexandru C., (2009), Software platform for analyzing & optimizing the mechanical systems, Proceedings of the10th IFToMM International Symposium on Science ofMechanisms and Machines - SYROM, 665-677.
2. Alexandru C., Pozna C., (2010), Simulation of a dual-axissolar tracker for improving the performance of aphotovoltaic panel, Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 224, 797-811.
3. Alexandru C., Tatu I.N., (2011), Simulating the virtual prototype of a photovoltaic tracking mechanism. Academic Journal of Manufacturing Engineering, 9, 6-11.
4. Andronic L., Hristache B., Enesca A., Visa M., Duta A.,(2009), Studies on Titanium Oxide catalyst doped withheavy metals (Cadmium, Copper and Nickel), Environmental Engineering and Management Journal, 8, 747-751.
5. Antonio J., (1994), Optimal trajectory planning for spray coating, Proceedings of the IEEE InternationalConference on Robotics and Automation, San Diego, California, 2570-2577.
6. Calin R.G., Comsit M., Nanu M., Duta A., (2005), Anautomatic nanostructured ceramics used in renewable energy sources, Science Jaargang, 26, 20-23.
7. Chen H., Xi N., Sheng W., Chen Y., (2002), CAD-basedautomated robot trajectory planning, Industrial Robots:an International Journal, 29, 426-433.
8. Enescu M., Alexandru C., (2011), Modeling and Simulationof a 6 DOF Robot, Proceedings of 2011 InternationalConference on Optimization of the Robots andManipulators - OPTIROB 2011, 44-48.
9. Ferretti G., Magnani G., Rocco M., (2004), Virtualprototyping of mechatronic systems, Annual Reviewsin Control, 28, 193-206.
10. Lamár K., (2002), DSP Control unit for a sensor less synchronous motor drive, Master's Thesis, Institute ofAutomation, "Kandó Kálmán" - Faculty of ElectricalEngineering, Budapest, Hungary.
11. Miller T.J.E., (1989), Brushless Permanent-Magnet and Reluctance Motor Drives, Clarendon Press, Oxford University Press, New York, United States.
12. Neagoe M., Gogu G., Diaconescu D., (2005), High degree accuracy modelling and calibration of serial robots with large errors, Product Engineering, 4, 397-408.
13. Perendis D., Gauckler L.J., (2005), Thin film depositionusing spray pyrolysis, Journal of Electroceramics, 14,103-111.
14. Potkonjak V., Dordevic G.S., Kostic D., Rasic M., (2000),Dynamics of anthropomorphic painting robot: Quality analysis and cost reduction, Robotics and Automous systems, 32, 17-38.
15. Sheng W., Sheng M., Chen Y., (2001), CAD-guided robotmotion planning, Industrial Robot, An InternationalJournal, 28, 143-151.
16. Spong M.W., Vidyasagar M., (1989), Robot dynamics andcontrol, John Wiley & Sons, New York, United States.
17. 2 Thin filmsprepared by sol-gel method, EnvironmentalEngineering and Management Journal, 10, 187-192.