Empirical study regarding the effects of minimum quantity lubricant utilization on performance characteristics in the drilling of Al 7075

Journal of the Brazilian Society of Mechanical Sciences and Engineering

Volumn 33, Issue 1, 2011, Pages 52-57

  Kilickap, Erol ^a   Huseyinoglu, Mesut ^a   Ozel, Cihan ^b  

^a DICLE UNIVERSITY   (Turkey)

^b FIRAT UNIVERSITY   (Turkey)

Author keywords

Aluminium composite; Drilling; MQL; Surface roughness

Indexed keywords

AL 7075; ALUMINIUM COMPOSITES; COOLING LIQUID; COOLING TECHNIQUE; CUTTING OPERATIONS; CUTTING PARAMETERS; CUTTING PROCESS; CUTTING SPEED; DRY PROCESSING; EMPIRICAL STUDIES; FEED-RATES; MINIMUM QUANTITY LUBRICANTS; MINIMUM QUANTITY LUBRICATION; MQL; OIL-WATER EMULSION; PERFORMANCE CHARACTERISTICS; PROCESSING TECHNIQUE; TEMPERATURE CHANGES; WORK PIECE SURFACE; WORK PIECES;

AIR LUBRICATION; BORON; BORON COMPOUNDS; COLD STORAGE; COMPRESSED AIR; COOLING; CUTTING; DRILLING; DRILLING FLUIDS; EMULSIFICATION; EMULSIONS; EXPERIMENTS; LIQUIDS; PHASE INTERFACES; SURFACE PROPERTIES; SURFACE ROUGHNESS;

CUTTING FLUIDS;

EID: 79955865348     PISSN: 16785878     EISSN: 18063691     Source Type: Journal    
DOI: 10.1590/S1678-58782011000100008     Document Type: Article

References (24)

1. Attanasio, A., Gelfi, M., Giardini, C. and Remino, C., 2006, "Minimal quantity lubrication in turning: Effect on tool wear", Wear, Vol. 260, pp. 333-338. (Pubitemid 43208700)
2. Bhowmick, S., Alpas, A.T., 2008, "Minimum quantity lubrication drilling of aluminium-silicon alloys in water using diamond-like carbon coated drills", International Journal of Machine Tools & Manufacture, Vol. 48, pp. 1429-1443.
3. Bono, M. and Ni, J., 2001, "The effects of thermal distortions on the diameter and cylindricity of dry drilled holes", International Journal of Machine Tools & Manufacture, Vol. 41, pp. 2261-2270. (Pubitemid 32785160)
4. Braga, D.U., Diniz, A.E., Miranda, G.W.A. and Coppini, N.L., 2002, "Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminium-silicon alloys", Journal of Materials Processing Technology, Vol. 122, pp. 127-138. (Pubitemid 34201305)
5. Bruni, C., Forcellese, A., Gabrielli, F. and Simoncini, M., 2006, "Effect of the lubrication-cooling technique, insert technology and machine bed material on the workpart surface finish and tool wear in finish turning of AISI 420B", International Journal of Machine Tools & Manufacture, Vol. 46, pp. 1547-1554. (Pubitemid 44160581)
6. Da Silva, L.R., Bianchi, E.C., Fusse, R.Y., Catai, R.E., França, T.V. and Aguiar, P.R., 2007, "Analysis of surface integrity for minimum quantity lubricant-MQL in grinding", International Journal of Machine Tools & Manufacture, Vol. 47, pp. 412-418. (Pubitemid 44767979)
7. Davidson, M.J., Balasubramanian, K. and Tagore, G.R.N., 2008, "Surface roughness prediction of flow-formed AA 6061 alloy by design of experiments", Journal of Materials Processing Technology, Vol. 202, pp. 41-46. (Pubitemid 351615543)
8. Dhar, N.R., Ahmed, M.T. and Islam, S., 2007, "An experimental investigation on effect of minimum quantitylubrication in machining AISI 1040 steel", International Journal of Machine Tools & Manufacture, Vol. 47, pp. 748-753. (Pubitemid 46162105)
9. Dhar, N.R., Islam, M.W., Islam, S. and Mithu, M.A.H., 2007, "The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel", Journal of Materials Processing Technology, Vol. 171, pp. 93-99. (Pubitemid 41815164)
10. Dhar, N.R., Kamruzzaman, M. and Ahmed, M., 2006, "Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel", Journal of Materials Processing Technology, Vol. 172, pp. 299-304. (Pubitemid 43227341)
11. Diniz, A.E. and Micaroni, R., 2007, "Influence of the direction and flow rate of the cutting fluid on tool life in turning process of AISI 1045 steel", International Journal of Machine Tools & Manufacture, Vol. 47, pp. 247-254. (Pubitemid 44738481)
12. Ezugwu, E.O., Bonney, J., Da Silva, R.B. and Çakir, O., 2007, "Surface integrity of finished turned Ti-6Al-4V alloy with PCD tools using conventional and high pressure coolant supplies", International Journal of Machine Tools & Manufacture, Vol. 47, pp. 884-891. (Pubitemid 46205140)
13. Heinemann, R., Hinduja, S., Barrow, G. and Petuelli, G., 2005, "Effect of MSS on the tool life of small twist drills in deep-hole drilling", International Journal of Machine Tools & Manufacture, Vol. 1, pp. 1-6. (Pubitemid 41497894)
14. Huseyinoglu, M. and Tosun, N., 2009, "Effect of Minimum Quantity Coolant on Surface Roughness in Milling of 7075 Al Alloy", Vol. 5. International Advanced Technologies Symposium (IATS'09), Karabuk, pp. 1321-1326.
15. Huseyinoglu, M., 2008, "Effect of minimum quantity coolant usage on performance characteristic in milling of 7075 aluminum alloy", Master Thesis, Firat University, Graduate School of Natural and Applied Sciences, Elazig, Turkey.
16. Kelly, J.F. and Cotterell, M.G., 2002, "Minimal lubrication machining of aluminium alloys", Journal of Materials Processing Technology, Vol. 120, pp. 327-334. (Pubitemid 34069993)
17. Kishawy, H.A., Dumitrescu, M., Ng, E.G. and Elbestawi, M.A., 2005, "Effect of coolant strategy on tool performance, chip morphology and surface quality during high-speed machining of A356 aluminum alloy", International Journal of Machine Tools & Manufacture, Vol. 45, pp. 219-227.
18. López de Lacalle, L.N., Angulo, C., Lamikiz, A. and Sánchez, J.A., 2006, "Experimental and numerical investigation of the effect of spray cutting fluids in high speed milling", Journal of Materials Processing Technology, Vol. 172, pp. 11-15. (Pubitemid 43144589)
19. Lianq Chern, G., 2006, "Experimental observation and analysis of burr formation mechanisms in face milling of aluminum alloys", International Journal of Machine Tools & Manufacture, Vol. 46, pp. 1517-1525.
20. Obikawa, T., Kamata, Y. and Shinozuka, J., 2006, "High-speed grooving with applying MQL", International Journal of Machine Tools & Manufacture, Vol. 46, pp. 1854-1861. (Pubitemid 44175806)
21. Ozcelik, B. and Bagci, E., 2006, "Experimental and numerical studies on the determination of twist drill temperature in dry drilling: A new approach", Materials and Design, Vol. 27, pp. 920-927. (Pubitemid 44089243)
22. Pawade, R.S., Joshi, S.S., Brahmankar, P.K. and Rahman, M., 2007, "An investigations of cutting forces and surface damage in high-speed turning of inconel 718", Journal of Materials Processing Technology, 192-193, 139-146. (Pubitemid 47187994)
23. Rahman, M., Kumar, S.A. and Salam, M.U., 2001, "Evaluation of minimal quantities of lubricant in end milling", International Journal of Advanced Manufacturing Technology, Vol. 18, pp. 235-241. (Pubitemid 32914694)
24. 4V with minimal quantity of lubricant", Journal of Materials Processing Technology, Vol. 179, pp. 124-127. (Pubitemid 44376525)