Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel

Journal of Materials Processing Technology

Volumn 172, Issue 2, 2006, Pages 299-304

  Dhar, N R ^a   Kamruzzaman, M ^a   Ahmed, Mahiuddin ^a  

^a BANGLADESH UNIVERSITY OF ENGINEERING AND TECHNOLOGY   (Bangladesh)

Author keywords

MQL; Steel; Tool wear and surface roughness; Turning

Indexed keywords

COST EFFECTIVENESS; ENVIRONMENTAL PROTECTION; LUBRICATION; SURFACE ROUGHNESS; WEAR OF MATERIALS;

CHIP FLUSHING FUNCTION; MINIMUM QUANTITY LUBRICATION (MQL);

MACHINING;

EID: 32444446105     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2005.09.022     Document Type: Article

References (24)

1. P. Leskover, and J. Grum The metallurgical aspect of machining Ann. CIRP 35 1 1986 537 550
2. H.K. Tonshoff, and E. Brinkomeier Determination of the mechanical and thermal influences on machined surface by microhardness and residual stress analysis Ann. CIRP 29 2 1986 519 532
3. M.C. Shaw, J.D. Piggtt, and L.P. Richardson Effect of cutting fluid upon chip-tool interface temperature Trans. ASME 71 1951 45 56
4. S. Paul, N.R. Dhar, and A.B. Chattopadhyay Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel Proceedings of the ICAMT-2000, UTM Malaysia 2000 209 214
5. C. Cassin, and G. Boothroyd Lubrication action of cutting fluids J. Mech. Eng. Sci. 7 1 1965 67 81
6. M. Mazurkiewicz, Z. Kubala, and J. Chow Metal machining with high pressure water-jet cooling assistance - a new possibility J. Eng. Ind. 111 1989 7 12
7. A. Alexander, A.S. Varadarajan, and P.K. Philip Hard turning with minimum cutting fluid: a viable green alternative on the shop floor Proceedings of the 18th AIMTDR 1998 152 155
8. M. Sokovic, and K. Mijanovic Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes JMPT 109 1-2 2001 181 189
9. F. Klocke, and G. Eisennblätter Dry cutting Ann. CIRP 46 2 1997 519 526
10. G. Byrne, and E. Scholta Environmentally clean machining processes - a strategic approach Ann. CIRP 42 1 1993 471 474
11. F. Klocke, and G. Eisenblatter Coated tools for metal cutting-features and applications Ann. CIRP 48 2 1999 515 525
12. U. Heisel, and M. Lutz Application of minimum quantity cooling lubrication technology in cutting processes Prod. Eng. II 1 1994 49 54
13. T. Wakabayashi Turning using extremely small amount of cutting fluids JSME 41 1 1998 143 148
14. J.W. Sutherland An experimental investigation of air quality in wet and dry turning Ann. CIRP 49 1 2000 61 64
15. S. Suda Evaluation of machinability with MQL system and effectiveness in production lines Procedings of the International Tribology Conference, Nagasaki, 2000 2001 203 208
16. J. McCabe, and M.A. Ostaraff Performance experience with near-dry machining of aluminum Lubr. Eng. 2001 22 27
17. T.F. MaClure, R. Adams, M.D. Gugger, Comparison of flood vs. microlubrication on machining performance, Internet: http://www.unist.com/ techsolve.html.
18. H.K. Tönshoff, and W. Spintig Machining of holes developments in drilling technology Ann. CIRP 1994 551 561
19. E. Lugscheider, O. Knotek, C. Barimani, T. Leyendecker, O. Lemmer, and R. Wenke Investigations on hard coated reamers in different lubricant free cutting operations Surf. Coat. Technol. 90 1997 172 177
20. N.R. Dhar, M.W. Islam, S. Islam, and M.A.H. Mithu The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel J. Mater. Process. Technol. 171 2006 93 99
21. V. Derflinger, H. Brändle, and H. Zimmermann New hard/ lubricant coating for dry machining Surf. Coat. Technol. 113 1996 286 292
22. D.U. Braga, A.E. Diniz, G. Miranda, and N.L. Coppini Minimal lubrication in the drilling process of aluminum-silicon alloy-A356 (SAE 323) Proceedings of the Third International Machining and Grinding Conference (SME), 1 Cincinnati, USA 1999 683 697
23. K.M. Rahman, Effect of minimum quantity lubrication (MQL) in drilling commercially used steels, M. Engg. Dissertation, BUET, Dhaka, Bangladesh, 2004.
24. N.R. Dhar, S. Islam, Improvement in machinability characteristics and working environment by minimum quantity lubrication, CASR Project Report, BUET, Dhaka, Bangladesh, 2005.