Designing mechanical systems for optimum diagnosability

Research in Engineering Design

Volumn 21, Issue 2, 2010, Pages 113-122

  Henning, Scott ^a   Paasch, Robert ^a  

^a Oregon State University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ANALYSIS AND MODELING; DIAGNOSABILITY; DIAGNOSABILITY ANALYSIS; DIAGNOSTIC ANALYSIS; DISTINGUISHABILITY; ELECTROMECHANICAL SYSTEMS; FAILURE MODES AND EFFECTS ANALYSIS; FAULT ISOLATION; LIFECYCLE COSTS; MATHEMATICAL METHOD; MATRIX MULTIPLICATION; MECHANICAL SYSTEMS; NO FAULT FOUND; RELATIONSHIP ANALYSIS;

COST BENEFIT ANALYSIS; LIFE CYCLE; MECHANICAL ENGINEERING; MECHANICS; OCEAN STRUCTURES; QUALITY ASSURANCE; SAFETY FACTOR;

FAILURE ANALYSIS;

EID: 77952217463     PISSN: 09349839     EISSN: None     Source Type: Journal    
DOI: 10.1007/s00163-009-0078-1     Document Type: Article

References (18)

1. Bahr NJ (1997) System safety engineering and risk assessment: a practical approach. Taylor & Francis, Washington, DC
2. GE Clark RK Paasch 1996 Diagnostic modeling and diagnosability evaluation of mechanical systems J Mech Des 118 3 425 431 10.1115/1.2826903
3. Eubanks CF, Steven K, Kosuke I (1996) System behavior modeling as a basis for advanced failure modes and effects analysis. In: Proceedings of the 1996 ASME computers in engineering conference
4. Eubanks CF, Steven K, Kosuke I (1997) Advanced failure modes and effects analysis using behavior modeling. In: Proceedings of the 1997 ASME design theory and methodology conference
5. M Fitzpatrick R Paasch 1999 Analytical method for the prediction of reliability and maintainability based life-cycle labor costs J Mech Des 121 4 606 613 10.1115/1.2829506
6. Heckerman D, John SB, Koos R (1994) Troubleshooting under uncertainty," technical report MSR-TR-94-7, Microsoft Research, September 1994
7. Henning S, Robert P (2000) "Distinguishability analysis for fault isolation in mechanical systems. Proceedings of the 2000 ASME design theory and methodology conference, Baltimore, MD
8. Kmenta S, Kosuke I (1998) Advanced FMEA using meta behavior modeling for concurrent design of products and controls. In: Proceedings of the 1998 ASME design engineering technical conferences
9. Kościelny JM, Michał B, Paweł R, Jose Sá da C (2006) Actuator fault distinguishability study for the DAMADICS benchmark problem. Control Eng Pract 14(6):645-652
10. Kurki M (1995) Model-Based fault isolation diagnosis for mechatronic systems. Technical Research Centre of Finland, Espoo
11. Leitch RD (1995) Reliability analysis for engineers: an introduction. Oxford University Press, Oxford
12. MD Murphy RK Paasch 1997 Reliability centered prediction technique for diagnostic modeling and improvement Res Eng Des 9 1 35 45 10.1007/BF01607056
13. DN Ruff RK Paasch 1997 Evaluation of failure diagnosis in conceptual design of mechanical systems J Mech Des 119 1 57 64 10.1115/1.2828789
14. Sen S et al (1996) Simulation-based testability analysis and fault diagnosis. In: Proceedings of the AUTOTESTCON'96 conference, pp 136-148
15. Simpson WR, Sheppard JW (1994) System test and diagnosis. Kluwer, Boston
16. RB Stone IY Tumer MV Wie 2005 The function-failure design method J Mech Des 127 3 397 407 10.1115/1.1862678 (Pubitemid 40843875)
17. L Trave-Massuyes T Escobet X Olive 2006 Diagnosability analysis based on component-supported analytical redundancy relations IEEE Trans Syst Man Cybern Part A Syst Hum 36 6 1146 1160 10.1109/TSMCA.2006.878984 (Pubitemid 44680561)
18. Wong B (1994) Diagnosability analysis for mechanical systems and human factors in diagnosability, M.S. thesis, Department of Mechanical Engineering, Oregon State University, Corvallis, Oregon