Monitoring of dry cutting and applications of cutting fluid

Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology

Volumn 224, Issue 2, 2010, Pages 209-219

  Tangjitsitcharoen, S ^a  

^a CHULALONGKORN UNIVERSITY   (Thailand)

Author keywords

Cutting force; Dry cutting; Mist cutting; Surface roughness; Tool wear; Turning; Wet cutting

Indexed keywords

CUTTING FORCES; DRY CUTTING; MIST CUTTING; TOOL WEAR; WET CUTTING;

CARBIDE TOOLS; CARBIDES; CARBON STEEL; CUTTING FLUIDS; LUBRICATION; METAL ANALYSIS; SURFACE PROPERTIES; SURFACE ROUGHNESS; TURNING; WEAR OF MATERIALS;

TOOL STEEL;

EID: 77249175315     PISSN: 13506501     EISSN: None     Source Type: Journal    
DOI: 10.1243/13506501JET555     Document Type: Article

References (25)

1. D. A. Axinte, W. Belluco, L. D. Chiffre, Reliable tool life measurements in turning-an application to cutting fluid efficiency evaluation Int. J. Mach. Tools Manuf. 41 (2001): 1003-1014
2. N. R. Dhar, M. Kamruzzaman, M. Ahmed, Effect of minimum quantity lubricant (MQL) on tool wear and surface roughness in turning AISI-4340 steel J. Mater. Process. Technol. 172 (2006): 299-304
3. A. E. Diniz, R. Micaroni, Cutting conditions for finish turning process aiming: the use of dry cutting Int. J. Mach. Tools Manuf. 42 (2002): 899-904
4. J. W. Sutherland, V. N. Kulur, N. C. King, An experimental investigation of air quality in wet and dry turning Ann. CIRP 49/1 (2000): 61-64
5. T. J. Ko, S. H. Park, H. S. Kim, Experimental verification of the mist generation mechanism in turning Int. J. Mach. Tools Manuf. 43 (2003): 115-120
6. H. A. Kishawy, M. Dumitrescu, E. G. Ng, M. A. Elbestawi, Effect of coolant strategy on tool performance, chip morphology and surface quality during high-speed machining of A356 aluminum alloy Int. J. Mach. Tools Manuf. 45 (2005): 219-227
7. M. Ii, H. Eda, T. Imai, M. Nishimura, T. Kawasaki, J. Shimizu, T. Yamamoto, L. Zhou, Development of water-content cutting fluids with a new concept fire prevention and environmental protection J. Int. Soc. Prec. Eng. Nanotechnol. 24 (2000): 231-236
8. K. L. Gunter, J. W. Sutherland, An experimental investigation into the effect of process conditions on the mass concentration of cutting fluid mist in turning J. Clean. Prod. 7 (1999): 341-350
9. O. Cakir, M. Kiyak, E. Altan, Comparison of gases applications to wet and dry cutting in turning J. Mater. Process. Technol. 153 (2004): 35-41
10. K. Weinert, I. Inasaki, J. W. Sutherland, T. Wakabayashi, Machining and minimum quantity lubrication Ann. CIRP 53/2 (2004): 511-537
11. N. R. Dhar, M. W. Islam, M. A. H. Mithu, The influence of minimum quantity lubricant (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel J. Mater. Process. Technol. 171 (2006): 93-99
12. M. Rahman, A. Senthil Kumar, M. U. Salam, Experi-mental evaluation on the effect of minimal quantities of lubricant in milling Int. J. Mach. Tools Manuf. 2 (2002): 539-547
13. A. S. Varadarajan, P. K. Philip, B. Ramamoorthy, Investigations on hard turning with minimal cutting fluid application (HTMF) and its comparison with dry and wet turning Int. J. Mach. Tools Manuf. 42 (2002): 193-200
14. T. Moriwaki, T. Shibasaka, T. Somkiat, Chip control on CNC turning (2003)
15. Y. Hiromi, M. Toshimichi, O. Nobuo, N. Tetsuo, S. Toshiro, K. Hiroshi, M. Makoto, S. Manabu, Study on neat dry machining of aluminium alloys Int. J. Jpn. Soc. Mech. Eng. 49 (2006): 83-89
16. H. Bao, M. G. Stevenson, An investigation of built-up edge formation in the machining of aluminium Int. J. Mach. Tool Des. Res. 16 (1976): 165-178
17. Lathe Tooling Catalog 54 (2007):
18. B. Tasdelen, H. Thordenberg, D. Olofsson, An ex-perimental investigation on contact length during minimum quantity lubrication (MQL) machining J. Mater. Process. Technol. 203 (2008): 221-231
19. M. Thomas, Y. Beauchamp, Statistical investigation of modal parameters of cutting tools in dry cutting Int. J. Mach. Tools Manuf. 43 (2003): 1093-1106
20. M. E. S. Abdelmoneim, R. F. Scrutton, Tool edge roundness and stable built-up formation in finish machining ASME J. Eng. Ind. 96 4 (1974): 1258-1267
21. T. H. C. Childs, Friction modeling in metal cutting Wear 260 (2006): 310-318
22. E. D. Anselmo, M. Ricardo, Cutting conditions for finish turning process aiming: the use of dry cutting Int. J. Mach. Tools Manuf. 42 (2002): 899-904
23. T. Moriwaki, T. Shibasaka, T. Somkiat, Development of in-process chip-breaking detection system in turning. Memoirs of graduate school of science and technology, Kobe University (2004): 1-19
24. R. Teti, I. S. Jawahir, K. Jemielniak, S. Segreto, S. Chen, J. Kossakowska, Chip form monitoring through advanced processing of cutting force sensor signals Ann. CIRP 55 1 (2006): 75-80
25. I. S. Jawahir, C. A. Luttervelt, Recent developments in chip control research and applications Ann. CIRP 42 2 (1993): 659-685