Evolution of subsequent yield surfaces and elastic constants with finite plastic deformation. Part-I: A very low work hardening aluminum alloy (Al6061-T6511)

International Journal of Plasticity

Volumn 25, Issue 9, 2009, Pages 1611-1625

  Khan, Akhtar S ^a   Kazmi, Rehan ^a   Pandey, Amit ^a   Stoughton, Thomas ^b  

^a Baltimore County   (United States)

^b GENERAL MOTORS CORPORATION   (United States)

Author keywords

Anisotropy; Cross effect; Elastic moduli; Finite plastic strain; Subsequent yield surfaces

Indexed keywords

AL ALLOYS; CLEVELAND; COMBINED TENSION-TORSION; CROSS-EFFECT; FINITE DEFORMATIONS; FINITE PLASTIC STRAIN; FREE END; INELASTIC EFFECTS; LOADING AND UNLOADING; LOADING DIRECTION; NON-LINEAR; PROPORTIONAL LOADING; REVERSE LOADING; SHEAR MODULUS; SPRING-BACK; SUBSEQUENT YIELD SURFACES; TENSION-TENSION; TORSIONAL LOADINGS; UNLOADING PATHS; WORK HARDENING; YIELD SURFACE;

ALUMINA; ALUMINUM; ALUMINUM ALLOYS; ANISOTROPY; ANNEALING; ELASTIC CONSTANTS; ELASTIC MODULI; LOADING; PLASTIC DEFORMATION; PLASTICS; SINGLE CRYSTALS; STRAIN; STRAIN HARDENING; STRUCTURAL LOADS; TORSIONAL STRESS; UNLOADING;

SURFACES;

EID: 65849270475     PISSN: 07496419     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijplas.2008.07.003     Document Type: Article

References (47)

1. Ascione L., Olivito R.S., and Spadea G. An experimental study on subsequent yield surfaces for metals. Mater. Struct. 15 (1982) 21-26
2. Chun B.K., Jinn J.T., and Lee J.K. Modeling the Bauschinger effect for sheet metals part I: theory. Int. J. Plast. 18 (2002) 571-595
3. Chun B.K., Jinn J.T., and Lee J.K. Modeling the Bauschinger effect for sheet metals part II: applications. Int. J. Plast. 18 (2002) 597-616
4. Cleveland R.M., and Ghosh A.K. Inelastic effects on springback in metals. Int. J. Plast. 18 (2002) 769-785
5. François M. A plasticity model with yield surface distortion for non proportional loading. Int. J. Plast. 15 (2001) 703-717
6. Gau J.-T., and Kinzel G.L. A new model for springback prediction in which the Bauschinger effect is considered. Int. J. Mech. Sci. 43 (2001) 1813-1832
7. Geng L., Shen Y., and Wagoner R.H. Anisotropic hardening equations derived from reverse-bend testing. Int. J. Plast. 18 (2002) 743-767
8. Gil C.M., Lissenden C.J., and Lerch B.A. Yield of Inconel 718 by axial-torsional loading at temperatures up to 649 C. J. Test. Eval. 20 (1999) 327-336
9. Gupta N.K., and Meyers A. Considerations of translated stress deviators in describing yield surfaces. Int. J. Plast. 8 (1992) 729-740
10. Helling, D.E., Miller, A.K., 1987. The incorporation of yield surface distortion into a unified constitutive model, part 1: equation development. Acta Mech. 69, 9-23.
11. Helling, D. E., Miller, A.K., 1988. The incorporation of yield surface distortion into a unified constitutive model, part 2: predictive capabilities. Acta Mech. 72, 39-53.
12. Helling D.E., Miller A.K., and Stout M.G. An experimental investigation of the yield surfaces of 1100-0 aluminium, 70:30 brass and an overaged 2040 aluminium alloy after various prestrains. J. Eng. Mat. Tech. ASME 108 (1986) 313-320
13. Hordon M.J., Lement B.S., and Averbach B.L. Influence of plastic deformation on expansivity and elastic modulus of aluminum. Acta Metall. 6 (1958) 446-453
14. Huang S., and Khan A.S. On the use of electrical-resistance metallic foil strain gages for measuring large dynamic plastic deformation. Exp. Mech. (1991) 122-125 June
15. Ishikawa H. Subsequent yield surface probed from its current center. Int. J. Plast. 13 (1997) 533-549
16. Ivey H.J. Plastic stress-strain relations and yield surfaces for aluminium alloys. J. Mech. Eng. Sci. 3 (1961) 15-31
17. Khan A.S., and Liang R. Behaviors of three BCC metals during non-proportional multi-axial loadings: experiments and modeling. Int. J. Plast. 12 (2000) 1443-1458
18. Khan A.S., and Wang X. On non proportional infinitesimal plastic deformation after finite plastic pre-straining and partial unloading. J. Mech. Phys. Solids 36 (1988) 519-535
19. Khan A.S., and Wang X. An experimental study on subsequent yield surfaces after finite shear pre-straining. Int. J. Plast. 9 (1993) 889-905
20. Khan A.S., Chen X., and Abdel-Karim M. Cyclic multiaxial and shear finite deformation response of OFHC: part I. Int. J. Plast. 23 (2007) 1285-1306
21. Khan, A.S., Pandey, A., Stoughton, T., 2009a. Evolution of subsequent yield surfaces and elastic constants with finite plastic deformation, Part-II: a very high work hardening aluminum alloy (annealed 1100 Al), Int. J. Plast., accepted for publication.
22. Khan, A.S., Pandey, A., Stoughton, T., 2009b. Evolution of subsequent yield surfaces and elastic moduli under tension-tension stress space with finite plastic deformation in aluminum alloys, Part-III. Int. J. Plast., accepted for publication.
23. Korkolis Y.P., and Kyriakides S. Inflation and burst of anisotropic aluminum tubes for hydroforming applications. Int. J. Plast. 24 (2008) 509-543
24. Korkolis Y.P., and Kyriakides S. Inflation and burst of aluminum tubes. Part II: An advanced yield function including deformation-induced anisotropy. Int. J. Plast. 24 (2008) 1625-1637
25. Korkolis, Y.P., Kyriakides, S., 2009. Path-dependent failure of inflated aluminum tubes. Int. J. Plast., in press, doi:10.1016/j.ijplas.2008.12.016.
26. Kowalsky U., Ahrens H., and Dinkler D. Distorted yield surfaces - modelling by higher order anisotropic hardening tensors. Comput. Mater. Sci. 16 (1999) 81-88
27. Michno M.J., and Findley W.N. An historical perspective of yield surface investigations for metals. Int. J. Non-Linear Mech. 11 (1976) 59-82
28. Mair W.N., and Pugh H.L.D. The effect of pre-strain on yield surfaces in copper. J. Mech. Eng. Sci. 6 (1964) 150-163
29. Morestin F., and Boivin M. On the necessity of taking into account the variation in the Young modulus with plastic strain in elastic-plastic software. Nucl. Eng. Design 162 (1996) 107-116
30. Moreton D.N., Moffat D.G., and Parkinson D.B. The yield surface behavior of pressure vessel steels. J. Strain Anal. Eng. Design 16 (1981) 127-136
31. Naghdi P.M., Essenburg F., and Koff W. An experimental study of initial and subsequent yield surfaces in plasticity. ASME J. Appl. Mech. 25 (1958) 201-209
32. Phillips A., and Das P.K. Yield surfaces and loading surfaces of aluminum and brass: an experimental investigation at room and elevated temperatures. Int. J. Plast. 1 (1985) 89-109
33. Phillips A., and Ricciuti M. Fundamental experiments in plasticity and creep of aluminum - extension of previous results. Int. J. Solids Struct. 12 (1976) 159-171
34. Rees D.W.A. A examination of yield surface distortion and translation. Acta Mech. 52 (1984) 15-40
35. Shiratori E., Ikegami K., and Kaneko K. The influence of the Bauschinger effect on the subsequent yield condition. Bull. JSME 16 (1973) 1482-1493
36. Stout M.G., Martin P.L., Helling D.E., and Canova G.R. Multiaxial yield behavior of 1100 aluminum following various magnitudes of pre-strain. Int. J. Plast. 1 (1985) 163-174
37. Suprun A.N. A constitutive model with three plastic constants: the description of anisotropic work hardening. Int. J. Plast. 22 (2006) 1217-1233
38. Tozawa Y. Plastic deformation behavior under conditions of combined stress. In: Koistinen D.P., and Wang N.-M. (Eds). Mechanics of Sheet Metal Forming (1978), Plenum Press, New York London
39. Wegener K., and Schlegel M. Suitability of yield functions for the approximation of subsequent yield surfaces. Int. J. Plast. 12 (1996) 1151-1177
40. William J.F., and Svensson N.L. Effect of tensile pre-strain on the yield locus of 1100-F Aluminum. J. Strain Anal. 5 (1970) 128-139
41. William J.F., and Svensson N.L. Effect of torsional pre-strain on the yield locus of 1100-F Aluminum. J. Strain Anal. 6 (1971) 263-272
42. Wu H.C., and Yeh W.C. On the experimental determination of yield surfaces and some results of annealed 304 stainless steel. Int. J. Plast. 7 (1991) 803-826
43. Wu H.C. Effect of loading-path on the evolution of yield surface for anisotropic metals subjected to large pre-strain. Int. J. Plast. 19 (2003) 1773-1800
44. Wu H.C. Anisotropic plasticity for sheet metals using the concept of combined isotropic-kinematic hardening. Int. J. Plast. 18 (2002) 1661-1682
45. Wu H.C. On finite plastic deformation of anisotropic metallic materials. Int. J. Plast. 19 (2003) 91-119
46. Yang M., Akiyama Y., and Sasaki T. Evaluation of change in material properties due to plastic deformation. J. Mater. Proc. Technol. 151 (2004) 232-236
47. Yoshida, F., Uemori, T., Okada, T., Toropov, V.V., 2000, Identification of material parameters in large-strain cyclic plasticity models for sheet metal forming applications. In: Khan, A.S., Zhan, H., Yuen, Y. (Eds.), Proceedings of the eaith International Symposium on Plasticity and Its Current Applications. NEAT Press, pp. 612-614.