Modeling aspects of low plastic strain amplitude multiaxial cyclic plasticity in conventional and ultrafine grain nickel

International Journal of Plasticity

Volumn 24, Issue 10, 2008, Pages 1837-1862

  Moosbrugger, J C ^a   Batane, N R ^a   Morrison, D J ^a  

^a Clarkson University   (United States)

Author keywords

A. Stress relaxation; B. Anisotropic material; B. Constitutive behavior; B. Cyclic loading; Ultrafine grain material

Indexed keywords

AGRICULTURAL PRODUCTS; COPPER PLATING; CORRELATION METHODS; ELASTICITY; GRAIN (AGRICULTURAL PRODUCT); HARDENING; KINEMATICS; LITHOGRAPHY; MAGNETIC FIELD EFFECTS; MAGNETISM; MAGNETOSTRICTION; NICKEL; NICKEL ALLOYS; PLASTICITY; PLASTICS; STRAIN;

AVERAGE GRAIN DIAMETER; CYCLIC PLASTICITY; ELSEVIER (CO); GRAIN SIZES; INELASTIC STRAINS; KINEMATIC HARDENING; KINEMATIC HARDENING MODEL; MEAN STRESSES; MODEL PARAMETERS; MODELING ASPECTS; MULTIAXIAL; OUT OF PHASE (OP); PLASTIC STRAINING; PLASTICITY MODELLING; SMALL STRAINS; STRAIN PATHS; TWO MATERIALS; ULTRAFINE GRAINED;

STRAIN RATE;

EID: 47049119824     PISSN: 07496419     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijplas.2008.02.007     Document Type: Article

References (78)

1. Abdel-Karim M., and Ohno N. Kinematic hardening model suitable for ratcheting with steady state. Int. J. Plast. 16 (2000) 225-240
2. Abu Al-Rub R.K., and Voyiadjis G.Z. A physically based gradient plasticity theory. Int. J. Plast. 22 (2006) 654-684
3. Armstrong, P.J., Frederick, C.O., 1966. A mathematical representation of the multiaxial Bauschinger effect. C.E.G.B. Report, RD/B/N 731.
4. Benallal A., and Marquis D. Constitutive equations for nonproportional elasto-viscoplasticity. ASME J. Eng. Mater. Techn. 109 (1987) 326-336
5. Bari S., and Hassan T. Anatomy of coupled constitutive models for ratcheting simulation. Int. J. Plast. 16 (2000) 381-409
6. Bari S., and Hassan T. Kinematic hardening rules in uncoupled modeling for multiaxial ratcheting simulation. Int. J. Plast. 17 (2001) 885-905
7. Bari S., and Hassan T. An advancement in cyclic plasticity modeling for multiaxial ratcheting simulation. Int. J. Plast. 18 (2002) 873-894
8. Basinski Z.S., and Basinski S.J. Fundamental aspects of low amplitude cyclic deformation in face-centred cubic crystals. Progr. Mater. Sci. 36 (1992) 89-148
9. Batane, N.R., Morrison, D.J., Moosbrugger, J.C., 2006. Cyclic plasticity and fatigue of ultra fine grain nickel produced by pulsed electrodeposition. In: Fatigue 2006: Proceedings of the Ninth International Fatigue Congress, Atlanta, GA, Elsevier, NY, FT430.
10. Batane N.R., Morrison D.J., and Moosbrugger J.C. Cyclic stress-strain behavior of conventional grain and ultrafine grain nickel under biaxial straining. Scripta Mater. 58 (2008) 955-958
11. Berbenni B., Favier V., and Berveiller M. Impact of the grain size distribution on the yield stress of heterogeneous materials. Int. J. Plast. 23 (2007) 114-142
12. Bozorth R.M. Ferromagnetism (1951), D. Van Nostrand Co., NY
13. Buque C., Bretschneider J., Schwab A., and Holste C. Dislocation structures in cyclically deformed nickel polycrystals. Mater. Sci. Eng. A 300 (2000) 254-262
14. Burlet H., and Cailletaud G. Numerical techniques for cyclic plasticity at variable temperature. Engng. Comput. 3 (1986) 143-153
15. Chaboche, J.-L., Dang-Van, K., Cordier, G., 1979. Modelization of the strain memory effect on the cyclic hardening of 316 stainless steel. In: Proceedings of the Fifth Interenational Conference on Struc. Mech. in Reactor Tech., Berlin, L11 (3).
16. Chaboche J.-L., and Nouailhas D. Constitutive modeling of ratcheting effects. Part I. Experimental facts and properties of classical models. ASME J. Eng. Mater. Techn. 111 (1989) 384-392
17. Chaboche J.-L., and Nouailhas D. Constitutive modeling of ratcheting effects. Part II. Possibilities of some additional kinematic rules. ASME J. Eng. Mater. Techn. 111 (1989) 409-416
18. Chaboche J.-L. On some modifications of kinematic hardening to improve the description of ratcheting effects. Int. J. Plast. 7 (1991) 661-678
19. Chaboche J.-L., and Jung O. Application of a kinematic hardening viscoplasticity model with thresholds to the residual stress relaxation. Int. J. Plast. 13 (1997) 785-807
20. Cho H.S., Hemker K.J., Lian K., Goettert J., and Dirras G. Measured mechanical properties of LIGA Ni structures. Sensor Actuat. A 103 (2003) 59-63
21. Delobelle P., Robinet P., and Bocher L. Experimental study and phenomenological modelization of ratcheting under uniaxial and biaxial loading on an austenitic stainless steel. Int. J. Plast. 11 (1995) 295-330
22. Doong S.H., Socie D.F., and Robertson I.M. Dislocation structures and nonproportional hardening. ASME J. Eng. Mater. Techn. 112 (1990) 456-464
23. Guionnet C. Modeling of ratcheting in biaxial experiments. ASME Eng. Mater. Techn. 114 (1992) 56-62
24. Hassan T., and Kyriakides S. Ratcheting in cyclic plasticity. Part I. Uniaxial behavior. Int. J. Plast. 8 (1992) 91-116
25. Hassan T., Corona E., and Kyriakides S. Ratcheting in cyclic plasticity. Part II. Multiaxial behavior. Int. J. Plast. 8 (1992) 117-146
26. Hassan T., and Kyriakides S. Ratcheting of cyclically hardening and softening materials. Part I. Uniaxial behavior. Part II. Multiaxial behavior. Int. J. Plast. 10 (1994) 149-212
27. Hemker K.J., and Last H. Microsample tensile testing of LIGA nickel for MEMS applications. Mater. Sci. Eng. A 319-321 (2001) 882-886
28. Holste C. Cyclic plasticity of nickel from single crystals to submicron polycrystals. Philos. Mag. 84 (2004) 299-315
29. Hubert H., and Schäfer R. Magnetic Domains: The Analysis of Magnetic Microstructures (1998), Springer, NY
30. Jia Y., Morrison D.J., and Moosbrugger J.C. The influence of magnetostriction on the shape of the hysteresis loop of cyclically deformed single crystal nickel. Scripta Mater. 53 (2005) 1025-1029
31. Jiang Y., and Kurath P. Nonproportional cyclic deformation: critical experiments and analytical modeling. Int. J. Plast. 13 (1997) 743-763
32. Jiang Y., and Sehitoglu H. Cyclic ratcheting of 1070 steel under multiaxial stress states. Int. J. Plast. 10 (1994) 579-608
33. Jiang Y., and Sehitoglu H. Multiaxial cyclic ratcheting under multiple step loading. Int. J. Plast. 10 (1994) 849-870
34. Jiang Y., and Sehitoglu H. Modeling of cyclic ratcheting plasticity. Part I. Development of constitutive relations. Part II. Comparison of model simulations with experiments. ASME J. Appl. Mech. 63 (1996) 720-733
35. Kaleta J., and Žebracki J. Application of the Villari effect in a fatigue examination of nickel. Fatigue Fract. Engng. Mater. Struct. 19 (1996) 1435-1443
36. Kanazawa K., Brown M.W., and Miller K.J. Cyclic deformation of 1% Cr-Mo-V steel under out-of-phase loads. Fatigue Eng. Mater. Struct. 2 (1979) 217-228
37. Kang G.Z., Li Y.G., and Gao Q. Non-proportionally multiaxial ratcheting of cyclic hardening materials at elevated temperatures: experiments and simulations. Mech. Mater. 37 (2005) 1101-1118
38. Kang G.Z., Li Y.G., Zhang J., Sun Y.F., and Gao Q. Uniaxial ratcheting and failure behaviours of two steels. Theor. Appl. Fract. Mech. 43 (2005) 199-209
39. Kang G.Z., Kan Q.H., Zhang J., and Sun Y.F. Time-dependent ratcheting experiments of SS304 stainless steel. Int. J. Plast. 22 (2006) 858-894
40. Kang G.Z., Li Y.G., Gao Q., Kan Q.H., and Zhang J. Uniaxial ratcheting behaviors of the steels with different cyclic softening/hardening features. Fatigue Fract. Eng. Mater. Struct. 29 (2006) 93-103
41. Khan A.S., Suh Y.S., Chen X., Takacs L., and Zhang H. Nanocrystalline aluminum and iron: mechanical behavior at quasi-static and high strain rates, and constitutive modeling. Int. J. Plast. 22 (2006) 195-209
42. Kang G.Z., Kan Q.H., and Zhang J. Constitutive modeling for uniaxial time-dependent ratcheting of SS304 stainless steel. Mech. Mater. 39 (2007) 488-499
43. Krempl E., and Lu H. The hardening and rate-dependent behavior of fully annealed AISI type 304 stainless steel under biaxial in-phase and out-of-phase strain cycling at room temperature. ASME J. Eng. Mater. Techn. 106 (1984) 376-382
44. Laird C., and Buchinger L. Hardening behavior in fatigue. Metall. Trans. 16A (1985) 2201-2214
45. Lamba H.S., and Sidebottom O.M. Cyclic plasticity for nonproportional paths. Part I. Cyclic hardening, erasure of memory, and subsequent strain hardening experiments. ASME J. Eng. Mater. Techn. 100 (1978) 96-103
46. Lukáš P., and Kunz L. Cyclic plasticity and substructure of metals. Mater. Sci. Eng. A 322 (2002) 217-227
47. McDowell D.L. An experimental study of the structure of constitutive equations for nonproportional cyclic plasticity. ASME J. Eng. Mater. Techn. 107 (1985) 307-315
48. McDowell D.L. A two surface model for transient nonproportional cyclic plasticity. Part I. Development of appropriate equations. ASME J. Appl. Mech. 52 (1985) 298-302
49. McDowell D.L., Stahl D.R., Stock S.R., and Antolovich S.D. Biaxial path dependence of deformation substructure of type 304 stainless steel. Metall. Trans. 19A (1988) 1277-1293
50. McDowell D.L. Stress state dependence of cyclic ratcheting behavior of two rail steels. Int. J. Plast. 11 (1995) 397-421
51. Moosbrugger J.C., and McDowell D.L. On a class of kinematic hardening rules for nonproportional cyclic plasticity. ASME J. Eng. Mater. Techn. 111 (1989) 87-98
52. Moosbrugger J.C. Anisotropic nonlinear kinematic hardening rule parameters from reversed proportional axial-torsional cycling. ASME J. Eng. Mater. Techn. 122 (2000) 18-28
53. Moosbrugger J.C., Morrison D.J., and Jia Y. Nonlinear kinematic hardening rule parameters-relationship to substructure evolution in polycrystalline nickel. Int. J. Plast. 16 (2000) 439-467
54. Morrison D.J. Influence of grain size and texture on the cyclic stress strain response of nickel. Mater. Sci. Eng. A 187 (1994) 11-21
55. Morrison D.J., Jia Y., and Moosbrugger J.C. Cyclic plasticity of nickel at low plastic strain amplitude: hysteresis loop shape analysis. Mater. Sci. Eng. A 314 (2001) 24-30
56. Morrow, J.D., 1965. Cyclic plastic strain energy of metals. In: Internal Friction Damping and Cyclic Plasticity. ASTM STP-378, pp. 45-87.
57. Mughrabi H. The cyclic hardening and saturation behaviour of copper single crystals. Mater. Sci. Eng. 33 (1978) 207-223
58. Mughrabi H. Self-consistent experimental determination of the dislocation line tension and long-range internal stresses in deformed copper crystals by analysis of dislocation curvatures. Mater. Sci. Eng. A (2001) 237-245
59. Nouailhas D., and Freed A.D. A viscoplastic theory for anisotropic materials. ASME J. Eng. Mater. Techn. 114 (1992) 97-104
60. Ohashi Y., Tanaka E., and Ooka M. Plastic deformation behavior of type 316 stainless steel subjected to out-of-phase strain cycles. ASME J. Eng. Mater. Techn. 107 (1985) 286-292
61. Ohno N., and Wang J.D. Kinematic hardening rules with critical state of dynamic recovery. Part I. Formulation and basic features for ratcheting behavior. Part II. Application to experiments of ratcheting behavior. Int. J. Plast. 9 (1993) 375-403
62. Ohno N. Constitutive modeling of cyclic plasticity with emphasis on ratcheting. Int. J. Mech. Sci. 40 (1998) 251-261
63. Ohno N., and Okumura D. Higher-order stress and grain size effects due to self-energy of geometrically necessary dislocations. J. Mech. Phys. Solids 55 (2007) 1879-1898
64. Polák J., Helešic J., and Obrtlík K. Nucleation stress for persistent slip bands in fatigued copper single crystals. Mater. Sci. Eng. A 101 (1988) 7-12
65. Polák J., Petrenec M., and Degallaix S. On the analysis of the hysteresis loop of ferritic steel in cyclic straining. Scripta Mater. 47 (2002) 731-736
66. Portier L., Calloch S., Marquis D., and Geyer P. Ratcheting under tension-torsion loadings: experiments and modeling. Int. J. Plast. 16 (2000) 303-335
67. Rao K.B.S., Valsan M., Sandhya R., Mannan S.L., and Rodriguez P. An assessment of cold work effects on strain-controlled low cycle fatigue behavior of type 304 stainless steel. Metall. Trans. 24A (1993) 913-924
68. r of the stress-induced change in magnetization as a function of magnetic field strength and stress amplitude. J. Magn. Magn. Mater. 98 (1991) 349-358
69. Sherman A.M. Fatigue properties of high strength low alloy steels. Metall. Trans. 6A (1975) 1035-1040
70. Sai K., and Cailletaud G. Multi-mechanism models for the description of ratcheting: effect of the scale transition rule and of the coupling between hardening variables. Int. J. Plast. 23 (2007) 1589-1617
71. Taleb L., Cailletaud G., and Blaj L. Numerical simulation of complex ratcheting tests with a multi-mechanism model type. Int. J. Plast. 22 (2006) 724-753
72. Tanaka E., Murakami S., and Ooka M. Effects of strain path shapes on non-proportional cyclic plasticity. J. Mech. Phys. Sol. 33 (1985) 559-575
73. Vincent L., Calloch S., Kurtyka T., and Marquis D. An improvement of multiaxial ratcheting modeling via yield surface distortion. ASME J. Eng. Mater. Techn. 124 (2002) 402-411
74. Vincent L., Calloch S., and Marquis D. A general cyclic plasticity model taking into account yield surface distortion for multiaxial ratcheting. Int. J. Plast. 20 (2004) 1817-1850
75. Voyiadjis G.Z., and Basuroychowdhury T.N. A plasticity model for multiaxial cyclic loading and ratcheting. Acta Mech. 126 (1998) 19-35
76. Yaguchi M., and Takahashi Y. Ratcheting of viscoplastic material with cyclic softening. Part 1. Experiments on modified 9Cr-1Mo steel. Int. J. Plast. 21 (2005) 43-65
77. Yaguchi M., and Takahashi Y. Ratcheting of viscoplastic material with cyclic softening. Part 2. Application of constitutive models. Int. J. Plast. 21 (2005) 835-860
78. Yoshida F. Uniaxial and biaxial creep-ratcheting behavior of SUS304 stainless steel at room temperature. Int. J. Press. Vess. Pip. 44 (1990) 207-223