A study of five flank machining of centrifugal compressor impellers

Journal of Engineering for Gas Turbines and Power

Volumn 124, Issue 1, 2002, Pages 177-181

  Tsay, D M ^a   Chen, H C ^a   Her, M J ^a  

^a NATIONAL SUN YAT SEN UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

COMPRESSORS; INTERPOLATION; MACHINING; SPLINES; SURFACE ROUGHNESS;

CENTRIFUGAL COMPRESSOR IMPELLERS;

IMPELLERS;

CENTRIFUGAL COMPRESSOR; IMPELLER; MACHINING;

EID: 0036461969     PISSN: 07424795     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1413768     Document Type: Article

References (16)

1. Goetz, A., 1970. Introduction to Differential Geometry, Addison-Wesley, Reading, MA.
2. do Carmo, M. P., 1976, Differential Geometry of Curves and Surfaces. Prentice-Hall, Englewood Cliffs, NJ.
3. Marciniak, K., 1987, "Influence Of surface Shape on Admissible Tool Positions in 5-Axis Face Milling," Comput-Aided Des., 19, No. 5, pp. 233-236.
4. Vickers, G. W., and Quan, K. W., 1989, "Ball-Mills Versus End-Mills for Curved Surface Machining," ASME J. Eng. Ind., 111, pp. 22-26.
5. Takeuchi, Y., and Watanable, T., 1992, "Generation of 5-Axis Control Collision-Free Tool Path and Post-Processing for NC Data," CIRP Ann., 41, pp. 539-542.
6. Oliver, J. H., Wysocki, D. A., and Goodman, E. D., 1993, "Gauge Detection Algorithms for Sculptured Surface NC Generation," ASME J. Eng. Ind., 115, pp. 139-144.
7. Suresh, K. H., and Yang, D. C. H., 1994, "Constant Scallop-Height Machining of Free-Form Surfaces," ASME J. Eng. Ind., 116, pp. 253-259.
8. Tsay, D. M., Yan, W. F., and Ho, H. C., 2001, "Generation of Five-Axis Cutter Paths for Turbomachinery Components," ASME J. Eng. Gas Turbines Power, 123, pp. 50-56.
9. Ravani, B., and Ku, T. S., 1991, "Bertrand Offsets of Ruled and Developable Surfaces." Comput.-Aided Des., 23, No. 2, pp. 145-152.
10. Stute, G., Storr, A., and Sielaff, W., 1979, "NC Programming of Ruled Surfaces for Five-Axis Machining," CIRP Ann., 28, No. 1, pp. 267-271.
11. Rehsteiner, F., 1993. "Collision-Free Five-Axis Milling of Twisted Ruled Surfaces," CIRP Ann., 42, No. 1, pp. 457-461.
12. Wu, C. Y., 1995, "Arbitrary Surface Flank Milling of Fan, Compressor, and Impeller Blades," ASME J. Eng. Gas Turbines Power, 117, pp. 534-539.
13. Tsay, D. M., and Her, M. J., 2001. "Identification of Undercutting and Machining of Twisted Ruled Surfaces," ASME J. Manuf. Sci. Eng., 123.
14. Rogers, D. F., and Adams, J. A., 1989, Mathematical Elements for Computer Graphics, McGraw-Hill, New York.
15. de Boor, C., 1978, A Practical Guide to Splines. Springer-Verlag, New York.
16. Lee, E. T. Y., 1989, "Choosing Nodes in Parametric Curve Interpolation," Comput. Aided Des., 21, pp. 363-370.