Decomposition of thermal and mechanical effects on microstructure and hardness of hard turned surfaces

Journal of Manufacturing Science and Engineering

Volumn 126, Issue 2, 2004, Pages 264-273

  Shi, Jing ^a   Liu, C Richard ^a  

^a SCHOOL OF INDUSTRIAL ENGINEERING   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CARBURIZING; DEFORMATION; HARDNESS; MICROSTRUCTURE; PLASTIC DEFORMATION; SCANNING ELECTRON MICROSCOPY; THERMAL EFFECTS; X RAY DIFFRACTION;

GAUSSIAN CURVE PARAMETERS (GCP); HARD TURNING; SURFACE INTEGRITY; TOOL WEAR;

TURNING;

EID: 3943104975     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1751190     Document Type: Review

References (30)

1. Liu, C. R., and Mittal, S., 1995, "Single Step Super-Finishing Resulting in Superior Surface Integrity," J. Manuf. Syst., 14, pp. 124-133.
2. Liu, C. R., and Mittal, S., 1996, "Single Step Super-Finish Hard Machining: Feasibility and Feasible Cutting Conditions," Rob. Comput.-Integr. Manufact., 12(1), pp. 15-24.
3. Agha, S., and Liu, C. R., 2000, "Experimental Study on the Performance of Superfinish Hard Turned Surfaces in Rolling Contact," Wear, 244, pp. 52-59.
4. Griffiths, B. J., and Furze, D. C., 1987, "Tribological Advantages of White Layers Produced by Machining," Trans. ASME, 109, pp. 338-342.
5. Neailey, K., 1988, "Surface Integrity of Machined Components/Micro Structural Aspects," Metall. Mater. Trans. A, 4(3), pp. 93-96.
6. Neailey, K., 1988, "Surface Integrity of Machined Components/Residual Stresses and Fatigue," Metall. Mater. Trans. A, 4(3), pp. 141-145.
7. Shaw, M. C., and Vyas, A., 1994, "Heat-Affected Zones in Grinding Steel," CIRP Ann., 43(1), pp. 279-282.
8. Li, J. M., Jin, J. C., Li, X. Q., Xie, Z., Xia, Z. Y., and Gao, X. S., 1995, "Structural Study on Grinding Affected Layers of Carburized Steel Bearing," Chinese Journal of Mechanical Engineering, 31(3), pp. 84-90.
9. Eda, H., Kishi, K., and Hashimoto, S., 1981, "The Formation Mechanism of Ground White Layers," Bull. Jpn. Soc. Mech. Eng., 24, pp. 743-747.
10. Okusa, K., Takahashi, H., and Nishizawa, M., 1978, "Behaviour of White Layer During Cutting of Iron and Steels," Bull. Jpn. Soc. Precis. Eng., 12(4), pp. 171-176.
11. Bulpett, R., 1992, "The Characterization of White-Etching Layers Formed on Engineering Steels," PhD dissertation, Brunel University.
12. Tonshoff, H. K., Wobker, H. G., and Brandt, D., 1995, "Hard Turning-Influences on the Workpiece Properties," Transactions of NAMRI/SME, Vol XXIII, pp. 215-220.
13. Tomlinson, W. J., 1991, "The Effect of Workpiece Speed and Grinding-Wheel Condition on the Thickness of White Layers Formed on EN.24 Ground Surfaces," J. Mater. Process. Technol., 25, pp. 105-110.
14. Abrao, A. M., and Aspinwall, D. K., 1996, "The Surface Integrity of Turned and Ground Hardened Bearing Steel," Wear, 196, pp. 279-284.
15. Berns, H., Segtrop, K., and Theisen, W., 1993, "Surface Integrity of Hard Alloy After Machining Using PCBN," Proc. 1st Int. Conf. On Computer Methods and Experimental Measurements for Surface Treatment Effects, pp. 293-303.
16. El-Wardany, T. I., Kishawy, H. A., and Elbestawi, M. A., 2000, "Surface Integrity of Die Material in High Speed Hard Machining, I. Micrographical Analysis, ASME," ASME J. Manuf. Sci. Eng., 122(4), pp. 620-631.
17. Wang, J. Y., 1998, "A New Methodology for Analyzing the Heat Transfer and Thermal Damage Considering Tool Flank Wear in Finish Hard Machining," PhD dissertation, Purdue University.
18. Barbacki, A., and Kawalec, M., 1997, "Structural Alterations in the Surface Layer During Hard Machining," J. Mater. Process. Technol., 64, pp. 33-39.
19. Naito, H., and Kawashiri, K., 1985, "Structure and Residual Stress in Surface Layer of Carburized-and-Quenched Steel Turned With CBN Tool," Res. Rep. Nagoya Munic. Ind. Res. Inst., 70, pp. 13-16.
20. Wang, J. Y., and Liu, C. R., 1998, "A New Concept for Decoupling the Cutting Forces due to Tool Flank Wear and Chip Formation in Hard Turning," Mach. Sci. Technol., 2(1), pp. 77-90.
21. Chou, Y. K., and Evans, C. J., 1999, "White Layers and Thermal Modeling of Hard Turned Surfaces," Int. J. Mach. Tools Manuf., 39(12), pp. 1863-1881.
22. Shi, J., and Liu, C. R., 2002, "Prediction of Chip Morphology and White Layer in Hard Machining by Finite Element Analysis," submitted to Mach. Sci. Technol., under revision.
23. Marburger, R. E., and Koistinen, D. P., 1961, "The Determination of Hardness in Steels from the Breadth of X-ray Diffraction Lines," Trans. Am. Soc. Met., 53, pp. 743-752.
24. Nakanishi, E., 1974, "An Application of Half-Width and Diffraction Line Profile Analysis," Reprint of the 11th Forum on Strength of Materials, The Society of Materials Science, Kyoto, Japan, pp. 41-47.
25. Ji, N., Lebrun, J. L., and Bonnin, J. J., 1989, "Tempering Treatment Study of Two Steels by X-Ray Diffraction Profile Analysis," Mater. Sci. Lett., 8(10), pp. 1127-1130.
26. Ji, N., Lebrun, J. L., and Sprauel, J. M., 1990, "Analysis of Broadened X-Ray Diffraction Profiles: Application to the Characterization of Carbon Steels," Mater. Sci. Eng., A, 127(1), pp. 71-77.
27. Kurita, M., and Hirayama, H., 1984, "An Estimation of Hardness of Hardened Steels by X-ray Diffraction Using a Gaussian Curve Fitting Method," ASTM J. Test. Eval., 12(1), pp. 13-19.
28. Quo, Y. B., and Liu, C. R., 2002, "Mechanical Properties of Hardened AISI 52100 Steel in Hard Machining Processes," ASME J. Manuf. Sci. Eng., 124(1), pp. 1-9.
29. Kurita, M., 1981, "A Statistical Analysis of X-ray Measurement by the Gaussian Curve Fitting Method," ASTM J. Test. Eval., 9(5), pp. 285-291.
30. Speich, G. R., and Taylor, K. A., 1992, "Tempering of Ferrous Martensite," Martensite, Olson, G. B., and Owen, W. S., ASM International.