Nanocrystalline diamond coating tools for machining high-strength Al alloys

International Journal of Refractory Metals and Hard Materials

Volumn 26, Issue 3, 2008, Pages 135-144

  Hu, J ^a   Chou, Y K ^a   Thompson, R G ^b  

^a University of Alabama   (United States)

^b Vista Engineering Inc   (United States)

Author keywords

Coating delamination; Diamond coating; Machining forces; Nanocrystalline diamond; Tool wear

Indexed keywords

ALUMINUM ALLOYS; AMORPHOUS MATERIALS; DELAMINATION; INORGANIC COATINGS; NANOCRYSTALLINE MATERIALS; PLASMA ENHANCED CHEMICAL VAPOR DEPOSITION; WEAR OF MATERIALS;

COATING DELAMINATION; DIAMOND COATING; MACHINING FORCES; MICROCRYSTALLINE DIAMOND COATING (MCD) TOOLS; TOOL WEAR;

DIAMOND CUTTING TOOLS;

EID: 38949201246     PISSN: 02634368     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijrmhm.2007.05.012     Document Type: Article

References (24)

1. Oles E.J., Inspektor A., and Bauer C.E. The new diamond-coated carbide cutting tools. Diam Relat Mater 5 (1996) 617-624
2. Shen C.H. Machining performance of thin film diamond coated inserts on 390 aluminum. Trans North American Manufacturing Research Institution of SME 22 (1994) 201-208
3. Shen C.H. The importance of diamond coated tools for agile manufacturing and dry machining. Surf Coat Technol 86-87 (1996) 672-677
4. Belmonte M., Ferro P., Fernandes A.J.S., Costa F.M., Sacramento J., and Silva R.R. Wear resistant CVD diamond tools for turning of sintered hardmetals. Diam Relat Mater 12 (2003) 738-743
5. Karner J., Pedrazzini M., Reineck I., Sjostrand M.E., and Bergmann E. CVD diamond coated cemented carbide cutting tools. Mater Sci and Eng A 209 (1996) 405-413
6. Schafer L., Fryda M., Stolley T., Xiang L., and Klages C.-P. Chemical vapour deposition of polycrystalline diamond films on high-speed steel. Surf Coat Technol 116-119 (1999) 447-451
7. Andrewes C.J.E., Feng H.-Y., and Lau W.M. Machining of an aluminum/SiC composite using diamond inserts. J Mat Proc Technol 102 (2000) 25-29
8. D'Errico G.E., and Calzavarini R. Turning of metal matrix composites. Journal J Mat Proc Technol 119 (2001) 257-260
9. Davim J.P. Diamond tool performance in machining metal-matrix composites. J Mat Proc Technol 128 (2002) 100-105
10. Polini R., Casadei F., D'Antonio P., and Traversa E. Dry turning of alumina/aluminum composites with CVD diamond coated Co-cemented tungsten carbide tools. Surf Coat Technol 166 (2003) 127-134
11. Chou Y.K., and Liu J. CVD diamond tool performance in composite machining. Surf Coat Technol 200 (2005) 1872-1878
12. Moulin D., Raymond O., Chevrier P., Lipinski P., and Barre T. CVD diamond coatings for machining. Mater Sci Forum 256 (2006) 55-60
13. Windischmann H., Epps G.F., Cong Y., and Collins R.W. Intrinsic stress in diamond films prepared by microwave plasma CVD. J Appl Phys 69 (1991) 2231-2237
14. Ferreira N.G., Abramof E., Leite N.F., Corat E.J., and Trava-Airoldi V.J. Analysis of residual Stress in diamond films by X-ray diffraction and micro-Raman spectroscopy. J Appl Phys 91 (2002) 2466-2472
15. Liu E., Li L., Blanpain B., and Celis J.P. Residual stresses of diamond and diamondlike carbon films. J Appl Phys 98 (2005) 0735151-0735155
16. Ager III J.W., and Drory M.D. Quantitative measurement of residual biaxial stress by Raman spectroscopy in diamond grown on a Ti alloy by chemical vapor deposition. Phys Rev B 48 (1993) 2601-2609
17. Grogler T., Zeiler E., Horner A., Singer R.F., and Rosiwal S.M. Microwave-plasma-CVD of diamond coatings onto titanium and titanium alloys. Surf Coat Technol 98 (1998) 1079-1091
18. Kitamura T., Hirakata H., and Itsuji T. Effect of residual stress on delamination from interface edge between nano-films. Eng Frac Mech 70 (2003) 2089-20101
19. Catledge S.A., and Vohra Y.K. High density plasma processing of diamond films on titanium: residual stress and adhesion measurements. J Appl Phys 78 (1995) 7053-7058
20. Catledge S.A., Borham J., Vohra Y.K., Lacefield W.R., and Lemons J.E. Nanoindentation hardness and adhesion investigations of vapor deposited nanostructured diamond films. J Appl Phys 91 (2002) 5347-5352
21. Hu J, Chou YK, Thompson RG, Burgess J, Street S. Characterizations of nanocrystalline diamond coating cutting tools. Surf Coat Technol 2007, in press.
22. Hu J, Chou YK, Thompson RG. On stress analysis of diamond coating cutting tools, Trans North American Manufacturing Research Institute of SME 2007;35:177-84.
23. Liu J, Chou YK, An investigation on cutting tool temperatures in composite machining assisted with heat-pipe Cooling. In: Proc ASME IMECE, manufacturing science and engineering 2005:IMECE2005-80323.
24. Gahlin R., Alahelisten A., and Jacobson S. The effects of compressive stresses on the abrasion of diamond coatings. Wear 196 (1996) 226-233