Burr formation in drilling intersecting holes with Machinable Austempered Ductile Iron (MADI™)

Journal of Manufacturing Processes

Volumn 9, Issue 1, 2007, Pages 35-46

  Ballou, Jason R ^a   Joshi, Suhas S ^a   DeVor, Richard E ^a   Kapoor, Shiv G ^a  

^a UNIVERSITY OF ILLINOIS AT URBANA CHAMPAIGN   (United States)

Author keywords

Burr; Drill; Exit surface curvature; Feed rate; Flank wear; Helix angle; MADI ; Point angle; Speed

Indexed keywords

DRILLING; MACHINABILITY; MACHINE TOOLS;

FEED RATE; FLANK WEAR; HELIX ANGLE; POINT ANGLE;

NODULAR IRON;

EID: 35948973166     PISSN: 15266125     EISSN: None     Source Type: Journal    
DOI: 10.1016/S1526-6125(07)70106-8     Document Type: Article

References (17)

1. Druschitz, A.P. and Fitzgerald, D.C. (2003). "MADI™: introducing a new, machinable, austempered ductile iron." Intermet (online document 2006 May 17). Available at www.intermet.com/resource/ images_resource/2003-01-0831.pdf
2. Druschitz, A.P. and tenPas, D.J. (2004). "Effect of liquid environment on tensile properties of ductile iron." SAE Technical Paper Series, 2004-01-0793, pp1-5.
3. Gillespie, L.K. (1999). Deburring and Edge Finishing Handbook, New York: ASME Press.
4. Guo, Y. and Dornfeld, D.A. (2000). "Finite element modeling of burr formation process in drilling 304 stainless steel." ASME Journal of Mfg. Science and Engg. (v122), pp612-619.
5. Kim, J., Min, S., and Dornfeld, D.A. (2001). "Optimization and control of drilling burr formation of AISI 304L and AISI 4118 based on drilling burr control charts." Int'l Journal of Machine Tools and Manufacture (v41, n7), pp923-936.
6. Kim, J. and Dornfeld, D.A. (2002). "Development of an analytical model for drilling burr formation in ductile materials." ASME Journal of Engg. Materials and Technology (v124, n2), pp192-198.
7. Leopold, J. (2004). "Methods of burr measurement and burr detection." VDI Berichte (v1860), pp223-229.
8. Min, S. and Dornfeld, D.A. (2001). "Finite element modeling of burr formation in metal cutting." Machining Science and Technology (v5, n3), pp307-322.
9. Min, S., Dornfeld, D.A., and Nakao, Y. (2003). "Influence of exit surface angle on drilling burr formation." ASME Journal of Mfg. Science and Engg. (v125, n4), pp637-643.
10. Pande S. and Relekar H. (1985). "Investigations on reducing burr formation in drilling." Int'l Journal of Machine Tool Design and Research (v26, n3), pp339-348.
11. Sartkulvanich, P. et al. (2004). "Investigation of the effect of tool edge geometry upon cutting variables, tool wear, and burr formation using finite element simulation - a progress report." AIP Conf. Proc. (v712), pp1347-1352.
12. Saunders, L. and Mauch, C. (2001). "An exit burr model for drilling of metals." ASME Journal of Mfg. Science and Engg. (v123), pp562-566.
13. Schneider, G. (2002). "Chapter 8, drills and drilling operations." Manufacturing Center (online document 2006 May 22). Available at www.manufacturingcenter.com/online_book/chap_8.pdf
14. Shaw, M.C. (1997). Metal Cutting Principles. New York: Oxford Univ. Press, p405.
15. Sofronas, A. and Taraman, K. (1976). "Model development for exit burr thickness as a function of drill geometry and feed." SME Technical Paper MR75-376. Dearborn, MI: Society of Manufacturing Engineers.
16. Stein J. and Dornfeld, D.A. (1996). "Influence of workpiece exit angle on burr formation in drilling intersecting holes." Transactions of NAMRI/SME (v24), pp39-44.
17. Stein, J. and Dornfeld, D.A. (1997). "Burr formation in drilling miniature holes." Annals of the CIRP (v46, n1), pp63-66.