Burr formation in drilling miniature holes

CIRP Annals - Manufacturing Technology

Volumn 46, Issue 1, 1997, Pages

  Stein, Julie M ^a   Dornfeld, David A ^a  

^a UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

Burr; Drilling; Formation

Indexed keywords

PROCESS CONTROL; WEAR OF MATERIALS;

BURR FORMATION;

DRILLING;

EID: 0030690655     PISSN: 00078506     EISSN: None     Source Type: Journal    
DOI: 10.1016/s0007-8506(07)60776-8     Document Type: Article

References (20)

1. Adachi, K. et al. (1987): "A Study on Burr in Low Frequency Vibratory Drilling," Bull. JSPE, 21,4,258-264.
2. Chern, G. L. (1993): "Analysis of Burr Formation and Breakout in Metal Cutting," Ph.D. Dissertation, Dept. of Mech. Engr., Univ. of California, Berkeley, April.
3. Gillespie, L. K. (1975b): "Burrs Produced by Drilling," Bendix Corporation, Unclassified Topical Report BDX-613-1248, December.
4. Gillespie, L. K. (1976a): "Effects of Drilling Variables on Burr Properties," Bendix Corporation, Unclassified Topical Report BDX-613-1502, March.
5. Hasegawa, Y. et al. (1975): "Burr in Drilling Aluminum and Prevention of It," S.M.E. Tech. Paper No. MR75-480.
6. Hashimura, M., Ueda, K., Dornfeld, D. (1995) "Analysis of Three Dimensional Burr Formation in Oblique Cutting," CIRP Annals, 44, 1, 27-30.
7. Hiranaka, M. et al. (1993): "Studies on Bending at Small Hole Drilling of Printed Wiring Boards," J. JSPE, 59, 1, 119-124.
8. Kanai, M., Kanda, Y. (1978): "Statistical Characteristics of Drill Wear and Drill Life for the Standardized Performance Tests, "CIRP Annals, 27.
9. Iwata, K., Moriwaki, T. (1981): "Basic Study of High Speed Micro Deep Drilling," CIRP Annals, 1.
10. Lorenz, G. (1979): "Helix Angle and Drill Performance," CIRP Annals, 28, 1, 3-86.
11. Link, R. (1992): "Gratbildung und Strategienzur Gratreduzierung," Ph.D. dissertation, Rheinisch-Westfalischen Technischen Hochschule Aachen.
12. Ohshima, I. et al. (1993): "Burr Formation and Deburring in Drilling Cross Holes," J.JSPE, 59, 1, 155-160.
13. Pekelharing, A.J. (1978): "The Exit Failure in Interrupted Cutting," CIRP Annals, 27, 1, 5-10.
14. Schulz, H. (1993): "Drilling of Small Holes in Printed Circuits," CIRP General Assembly, STC"C", Edinburgh, August.
15. Stein, J.M. (1995) Burr Formation in Precision Drilling. Ph. D. Dissertation, Dept. of Mech.Engg., University of California at Berkeley.
16. Stein, J. M., Dornfeld, D. A. (1995) "An Analysis of the Burrs in Drilling Precision Miniature Holes Using a Fractional Factorial Design", Proc IMECE, ASME, December.
17. Stein, J., Dornfeld, D. (1996) "Influence of Workpiece Exit Angle on Burr Formation in Drilling Intersecting Holes", Tran.NAMRC,24, 39.
18. Stein, J., Dornfeld, D. (1997) "An Architecture for Integrated Design and Manufacturing of Precision Mechanical Components" NAMRC (to appear).
19. Sugawara, A., Inagaki, K. (1982): "Effect of Workpiece Structure on Burr Formation in Micro-drilling," Precision Engineering,4, 1 , 9-14.
20. Takeyama, H. et al. (1993): "Study on Oscillatory Drilling Aiming at Prevention of Burr," J.JSPE, 59, 10, 1719-1724.