Relationship between test severity and wear mode transition in micro-abrasive wear tests

Wear

Volumn 263, Issue 1-6 SPEC. ISS., 2007, Pages 111-116

  Cozza, R C ^a   de Mello, J D B ^b   Tanaka, D K ^a   Souza, R M ^a  

^a Polytechnic School   (Brazil)

^b FEDERAL UNIVERSITY OF UBERLÂNDIA   (Brazil)

Author keywords

Grooving abrasion; Micro abrasive wear testing; Rolling abrasion; Test severity; Wear modes

Indexed keywords

ABRASIVES; BALL BEARINGS; HARDNESS; PARTICLE SIZE; SILICON CARBIDE;

GROOVING ABRASION; ROLLING ABRASION; TEST SEVERITY; WEAR MODES;

WEAR OF MATERIALS;

ABRASIVES; BALL BEARINGS; HARDNESS; PARTICLE SIZE; SILICON CARBIDE; WEAR OF MATERIALS;

EID: 34748866700     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2007.01.099     Document Type: Article

References (37)

1. Cozza R.C., Souza R.M., and Tanaka D.K. Wear mode transition during the micro-scale abrasion of WC-Co P20 and M2 tool steel. XVIII International Congress of Mechanical Engineering Proceedings of COBEM 2005. Ouro Preto, MG, Brazil (2005)
2. R.C. Cozza, Wear coefficient and wear modes transition study in micro-abrasive wear testing, M.Sc. Dissertation, Polytechnic School of the University of São Paulo, São Paulo, Brazil, 2006, 192 p. (in Portuguese).
3. W.M. da Silva, Effect of pressing pressure and iron powder size on the micro-abrasion of steam-oxidized sintered iron, M.Sc. Dissertation, Federal University of Uberlândia, Uberlândia, Brazil, 2003, 98 p. (in Portuguese).
4. Trezona R.I., Allsopp D.N., and Hutchings I.M. Transitions between two-body and three-body abrasive wear: influence of test conditions in the microscale abrasive wear test. Wear 225-229 (1999) 205-214
5. da Silva W.M., Binder R., and de Mello J.D.B. Abrasive wear of steam-treated sintered iron. Wear 258 (2005) 166-177
6. Batista J.C.A., Matthews A., and Godoy C. Micro-abrasive wear of PVD duplex and single-layered coatings. Surf. Coat. Technol. 142-144 (2001) 1137-1143
7. Batista J.C.A., Godoy C., and Matthews A. Micro-scale abrasive wear testing of duplex and non-duplex (single-layered) PVD (Ti,Al)N, TiN and Cr-N coatings. Tribol. Inter. 35 (2002) 363-372
8. Batista J.C.A., Joseph M.C., Godoy C., and Matthews A. Micro-abrasion wear testing of PVD TiN coatings on untreated and plasma nitrided AISI H13 steel. Wear 249 (2002) 971-979
9. Baptista A.M., Ferreira J., and Pinto N. Micro-abrasive wear testing by rotating ball. Proceedings of the Seventh Portuguese Conference of Tribology (2000), Porto, Portugal (in Portuguese)
10. Bello J.O., and Wood R.J.K. Micro-abrasion of filled and unfilled polyamide 11 coatings. Wear 258 (2005) 294-302
11. Bose K., and Wood R.J.K. Optimun tests conditions for attaining uniform rolling abrasion in ball cratering tests on hard coatings. Wear 258 (2005) 322-332
12. Kattamis T.Z., Chen M., Skolianos S., and Chambers B.V. Effect of residual stresses on the strengh, adhesion and wear resistance of SiC coatings obtained by plasma-enhanced chemical vapor deposition on low alloy steel. Surf. Coat. Technol. 79 (1994) 43-48
13. Mergler Y.J., and Huis H. 't Veld, Micro-abrasive wear of semi-crystalline polymers. Tribol. Res. Design Eng. Syst. (2003) 165-173
14. Rutherford K.L., and Hutchings I.M. A micro-abrasive wear test, with particular application to coated systems. Surf. Coat. Technol. 79 (1996) 231-239
15. Ramalho A. Micro-scale abrasive wear of coated surfaces-prediction models. Surf. Coat. Technol. 197 (2005) 358-366
16. Adachi K., and Hutchings I.M. Wear-mode mapping for the micro-scale abrasion test. Wear 255 (2003) 23-29
17. Adachi K., and Hutchings I.M. Sensitivity of wear rates in the micro-scale abrasion test to test conditions and material hardness. Wear 258 (2005) 318-321
18. C.H. da Silva, Degradation of UHMWPE and POM due to the tribologic action against stainless steel and alumina, Ph.D Thesis, Polytechnic School of the University of São Paulo, São Paulo, Brazil, 2003, 294 p. (in Portuguese).
19. Oberg E., Jones F.D., Horton H.L., and Ryffel H.H. Machinery's Handbook. 26th ed. (2000), Industrial Press Inc., New York
20. Cozza R.C., Souza R.M., and Tanaka D.K. Micro-abrasive wear of DC and pulsed DC titanium nitride thin films with different levels of film residual stresses. Surf. Coat. Technol. 201 (2006) 4242-4246
21. Cozza R.C., Souza R.M., and Tanaka D.K. Ball wear influence at the caps formation in the micro-abrasive wear testing by rotative fix ball. IV National Congress of Mechanical Engineering-Proceedings of CONEM 2006 (2006), Recife, PE, Brazil (in Portuguese)
22. Gee M.G., Gant A.J., Hutchings I.M., Kusano Y., Schiffman K., Van Acker K., Poulat S., Gachon Y., von Stebut J., Hatto P., and Plint G. Results from an interlaboratory exercise to validate the micro-scale abrasion test. Wear 259 (2005) 27-35
23. Trezona R.I., and Hutchings I.M. Three-body abrasive wear testing of soft materials. Wear 233-235 (1999) 209-221
24. Shipway P.H., and Hodge C.J.B. Microabrasion of glass-the critical role of ridge formation. Wear 237 (2000) 90-97
25. Gee M.G., Gant A., Hutchings I.M., Bethke R., Schiffman K., Van Acker K., Poulat S., Gachon Y., and von Stebut J. Progress towards standardisation of ball cratering. Wear 255 (2003) 1-13
26. Bello J.O., and Wood R.J.K. Grooving micro-abrasion of polyamide 11 coated carbon steel tubulars for downhole application. Wear 255 (2003) 1157-1167
27. Shipway P.H., and Howell L. Microscale abrasion-corrosion behaviour of WC-Co hardmetals and HVOF sprayed coatings. Wear 258 (2005) 303-312
28. Chen H., Xu C., Zhou Q., Hutchings I.M., Shipway P.H., and Liu J. Micro-scale abrasive wear behaviour of HVOF sprayed and laser-remelted conventional and nanostructured WC-Co coatings. Wear 258 (2005) 333-338
29. Shipway P.H., and Hogg J.J. Dependence of microscale abrasion mechanisms of WC-Co hardmetals on abrasive type. Wear 259 (2005) 44-51
30. Gee M.G., and Wicks M.J. Ball crater testing for the measurement of the unlubricated sliding wear of wear-resistant coatings. Surf. Coat. Technol. 133/134 (2000) 376-382
31. Ceschini L., Palombarini G., Sambogna G., Firrao D., Scavino G., and Ubertalli G. Friction and wear behaviour of sintered steels submitted to sliding and abrasion tests. Tribol. Inter. 39 (2006) 748-755
32. Stachowiak G.W. Particle angularity and its relationship to abrasive and erosive wear. Wear 241 (2000) 214-219
33. Allsopp D.N., and Hutchings I.M. Micro-scale abrasion and scratch response of PVD coatings at elevated temperatures. Wear 251 (2001) 1308-1314
34. Stachowiak G.B., and Stachowiak G.W. Wear mechanisms in ball-cratering tests with large abrasive particles. Wear 256 (2004) 600-607
35. Kusano Y., and Hutchings I.M. Sources of variability in the free-ball micro-scale abrasion test. Wear 258 (2005) 313-317
36. Rutherford K.L., and Hutchings I.M. Theory and application of a micro-scale abrasive wear test. J. Test. Eval. (JTEVA) 25 2 (1997) 250-260
37. Izhevskyi V.A., Genova L.A., Bressiani J.C., and Bressiani A.H.A. Liquid phase sintered SiC ceramics from starting materials of different grade. Cerâmica 50 (2004) 261-267