Development and testing of a novel joint wear simulator and investigation of the viability of an elastomeric polyurethane for total-joint arthroplasty devices

Wear

Volumn 262, Issue 3-4, 2007, Pages 331-339

  Schwartz, Christian J ^a   Bahadur, Shyam ^b  

^a Department of Electrical and Computer Engineering   (United States)

^b Iowa State University   (United States)

Author keywords

Dual Axis Wear Simulator; Polyurethane biomaterials; Total joint replacement; UHMWPE; Wear

Indexed keywords

ELASTOMERS; HIP PROSTHESES; PATIENT TREATMENT; POLYURETHANES; SIMULATORS; ULTRAHIGH MOLECULAR WEIGHT POLYETHYLENES; WEAR OF MATERIALS;

DUAL AXIS WEAR SIMULATORS; POLYURETHANE BIOMATERIALS; TOTAL JOINT REPLACEMENT;

BIOMATERIALS;

BIOMATERIALS; ELASTOMERS; HIP PROSTHESES; PATIENT TREATMENT; POLYURETHANES; SIMULATORS; ULTRAHIGH MOLECULAR WEIGHT POLYETHYLENES; WEAR OF MATERIALS;

EID: 33846196591     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2006.05.018     Document Type: Article

References (24)

1. DeFrances C.J., and Hall M.J. 2002 National Hospital Discharge Survey. Adv. Data 342 (2004) 1-29
2. Dumbleton J.H., Manley M.T., and Edidin A.A. A literature review of the association between wear rate and osteolysis in total hip arthroplasty. J. Arthroplasty 17 5 (2002) 649-661
3. Oonishi H., Kadoya Y., and Masuda S. Gamma-irradiated cross-linked polyethylene in total hip replacements-analysis of retrieved sockets after long-term implantation. J. Biomed. Mater. Res. 58 2 (2001) 167-171
4. Muratoglu O.K., O'Connor D.O., Bragdon C.R., Delaney J., Jasty M., Harris W.H., Merrill E., and Venugopalan P. Gradient crosslinking of UHMWPE using irradiation in molten state for total joint arthroplasty. Biomaterials 23 3 (2002) 717-724
5. Muratoglu O.K., Bragdon C.R., O'Connor D.O., Jasty M., Harris W.H., Gul R., and McGarry F. Unified wear model for highly crosslinked ultra-high molecular weight polyethylenes (UHMWPE). Biomaterials 20 16 (1999) 1463-1470
6. Stewart T., Jin Z.M., and Fisher J. Analysis of contact mechanics for composite cushion knee joint replacements. Proc. Inst. Mech. Eng. [H] 212 1 (1998) 1-10
7. Suciu A.N., Iwatsubo T., and Matsuda M. Theoretical investigation of an artificial joint with micro-pocket-covered component and biphasic cartilage on the opposite articulating surface. J. Biomech. Eng. 125 4 (2003) 425-433
8. Raimondi M.T., Santambrogio C., Pietrabissa R., Raffelini F., and Molfetta L. Improved mathematical model of the wear of the cup articular surface in hip joint prostheses and comparison with retrieved components. Proc. Inst. Mech. Eng. [H] 215 4 (2001) 377-391
9. Smith S.L., Ash H.E., and Unsworth A. A tribological study of UHMWPE acetabular cups and polyurethane compliant layer acetabular cups. J. Biomed. Mater. Res. 53 6 (2000) 710-716
10. Stewart T., Jin Z.M., and Fisher J. Friction of composite cushion bearings for total knee joint replacements under adverse lubrication conditions. Proc. Inst. Mech. Eng. [H] 211 6 (1997) 451-465
11. Quigley F.P., Buggy M., and Birkinshaw C. Selection of elastomeric materials for compliant-layered total hip arthroplasty. Proc. Inst. Mech. Eng. [H] 216 1 (2002) 77-83
12. ASTM F 732-00, Wear Test Method for Wear Testing of Polymeric Materials used in Total Joint Prostheses. Annual Book of ASTM Standards, ASTM International, 2000.
13. Saikko V. A multidirectional motion pin-on-disk wear test method for prosthetic joint materials. J. Biomed. Mater. Res. 41 1 (1998) 58-64
14. Bragdon C.R., O'Connor D.O., Lowenstein J.D., Jasty M., and Syniuta W.D. The importance of multidirectional motion on the wear of polyethylene. Proc. Inst. Mech. Eng. [H] 210 3 (1996) 157-165
15. Turell M., Wang A., and Bellare A. Quantification of the effect of cross-path motion on the wear rate of ultra-high molecular weight polyethylene. Wear 255 2 (2003) 1034-1039
16. Hall R.M., Unsworth A., Siney P., and Wroblewski B.M. Wear in retrieved Charnley acetabular sockets. Proc. Inst. Mech. Eng. [H] 210 3 (1996) 197-207
17. Biggs S.A., Bragdon C.R., Garas K., Muratoglu O.K., Caruso P.J., and Harris W.H. Qualitative analysis of polyethylene particles extracted from bovine serum used in a hip simulator. 11th Conference of the European Society of Biomechanics. Toulouse, France (1998)
18. McKellop H.A., and Clarke I.C. Evolution and evaluation of materials-screening machines and joint simulators in predicting in vivo wear phenomena. In: Ducheyne P., and Hastings G.W. (Eds). Functional Behavior of Orthopedic Biomaterials (1984), CRC Press, Inc., Boca Raton, FL 51-85
19. Wang A., Sun D.C., Stark C., and Dumbleton J.H. Wear mechanisms of UHMWPE in total joint replacements. Wear 181 1 (1995) 241-249
20. Saikko V., Calonius O., and Keranen J. Effect of slide track shape on the wear of ultra-high molecular weight polyethylene in a pin-on-disk wear simulation of total hip prosthesis. J. Biomed. Mater. Res. B Appl. Biomater. 69 2 (2004) 141-148
21. Sambasivan S., Fischer D.A., Shen M.C., and Hsu S.M. Molecular orientation of ultrahigh molecular weight polyethylene induced by various sliding motions. J. Biomed. Mater. Res. 70B 2 (2004) 278-285
22. Saikko V., and Ahlroos T. Type of motion and lubricant in wear simulation of polyethylene acetabular cup. Proc. Inst. Mech. Eng. [H] 213 4 (1999) 301-310
23. Saikko V. Effect of Lubricant Protein Concentration on the Wear of Ultra-High Molecular Weight Polyethylene Sliding Against a CoCr Counterface (2003)
24. Charnley J. Factors in the design of an artificial hip joint. Proc. Inst. Mech. Eng. 181 3J (1966) 104