Evolution of fretting fatigue damage and relaxation of residual stress in shot-peened Ti-6AI-4V

Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science

Volumn 36, Issue 12, 2005, Pages 3385-3396

  Martinez, S A ^a   Sathish, S ^b   Mall, S ^c   Blodgett, M P ^a  

^a AIR FORCE RESEARCH LABORATORY   (United States)

^b UNIVERSITY OF DAYTON RESEARCH INSTITUTE   (United States)

^c Air Force Institute of Technology   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

DELAMINATION; FATIGUE OF MATERIALS; FRACTURE; FRETTING CORROSION; MICROCRACKS; RESIDUAL STRESSES; SCANNING ELECTRON MICROSCOPY; SHOT PEENING; X RAY DIFFRACTION ANALYSIS;

FRETTING FATIGUE DAMAGE; SURFACE RESIDUAL STRESS;

TITANIUM ALLOYS;

EID: 33644503202     PISSN: 10735623     EISSN: None     Source Type: Journal    
DOI: 10.1007/s11661-005-0012-8     Document Type: Article

References (31)

1. R.B. Waterhouse: Int. Mater. Rev., 1992, vol. 37, pp. 77-97.
2. T. Nicholas: Int. J. Fatigue, 1999, vol. 21, pp. S221-S231.
3. J. Gray: Characterization of Fretting Fatigue Damage in Aircraft Turbine Disks, Center for NDE, Iowa State University, Ames, IA, 1997.
4. H. Lee, O. Jin, and S. Mall: Fatigue Fract. Eng. Mater., 2003, vol. 26, pp. 1-12.
5. R.B. Waterhouse and A.J. Trowsdale: J. Appl. Phys., 1992, vol. 25, pp. A236-A239.
6. R.B. Waterhouse and D.E. Taylor: Wear, 1974, vol. 29, pp. 337-44.
7. A. Benrabah, C. Langlade, and A.B. Vannes: Wear, 1999, vol. 224, pp. 267-73.
8. D.W. Hoeppner: Mechanisms of Fretting-Fatigue and Their Impact on Test Methods Development, ASTM STP 1159, ASTM, Philadelphia, PA, 1992, pp. 23-32.
9. R.A. Antoniou and Radtke: Mater. Sci. Eng., 1997, vol. A237, pp. 229-40.
10. S. Faanes and U.S. Fernando: Fatigue Fract. Eng. Mater. Struct., 1994, vol. 17 (8), pp. 939-47;
11. C.D. Lykins, S. Mall, and V. Jain: Fatigue Fract. Eng. Mater. Struct., 2001, vol. 24, pp. 461-73.
12. S. Fouvry, Ph. Kapsa, and L. Vincent: Wear, 1995, vol. 185, pp. 35-46.
13. M.P. Szolwinski and T.N. Farris: Wear, 1996, vol. 198, pp. 93-107.
14. D.A. Hills and D. Nowell: Mech. Fretting Fatigue, Kluwer Academic Publishers, Hingham, MA, 1994.
15. R.B. Waterhouse: Proc. Inst. Mech. Eng., 1955, vol. 169, pp. 1157-64.
16. S.A. Namjoshi, V.K. Jain, and S. Mall: Trans. ASME, 2002, vol. 124, pp. 222-28.
17. R. Cortez, S. Mall, and J.R. Calcaterra: Int. J. Fatigue, 1999, vol. 21, pp. 709-17.
18. C.T. Tsai and S. Mall: Finite Element Analysis Des., 2000, vol. 36, pp. 171-87.
19. C.D. Lykins: Ph.D. Dissertation, University of Dayton, Dayton, OH, 1999.
20. S. Suresh, T.A. Venkatesh, B.P. Conner, C.S. Lee, A.E. Giannakopolous, and T.C. Lindley: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1131-46.
21. S.A. Martinez, S. Sathish, M.P. Blodgett, S. Namjoshi, and S. Mall: Review of Quantitative Nondestructive Evaluation, AIP, 2003, vol. 22, pp. 1531-37.
22. S.A. Martinez, S. Sathish, M.P. Blodgett, and M.J. Shepard: J. Exp. Mech., 2003, vol. 43 (2), pp. 1-7.
23. S.A. Martinez, S. Sathish, M.P. Blodgett, and M.J. Shepard: Proc. 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conf. and Exhibit, Indianapolis, IN, July 2002, pp. 7-10.
24. I.C. Noyan and J.B. Cohen: Wear, 1983, vol. 84, pp. 183-202.
25. V. Hauk: Structural and Residual Stress Analysis by Nondestructive Methods, Elsevier Science, Danvers, MA, 1997.
26. V.M. Hauk and E. Macherauch: Adv. X-Ray Analysis, 1984, vol. 27, pp. 81-99.
27. G.H. Farrahi and Maeder: Fatigue Fract. Eng. Mater., 1992, vol. 15, pp. 91-102.
28. S.A. Martinez, S. Sathish, M.P. Blodgett, and S. Mall: Proc. 10th World Int. Conf. on Titanium, 2003, vol. 2, p. 1039.
29. N.P. Suh: Wear, 1973, vol. 25, pp. 111-24.
30. N.P. Suh: Tribophysics, Prentice-Hall, Englewood Cliffs, NJ, 1986.
31. N.P. Suh, S. Jahanmir, E.P. Abrahamson, and A.P.L. Turner: J. Lubr. Technol., 1974, pp. 631-37.