Machining-induced residual stress: Experimentation and modeling

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 122, Issue 1, 2000, Pages 20-31

  Jacobus, Kurt ^a   DeVor, R E ^a   Kapoor, S G ^a  

^a United States of America   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 0001875628     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.538906     Document Type: Article

References (18)

1. Henriksen, E. K., 1951, “Residual Stresses in Machined Surfaces,” Trans. ASME, 73, pp. 69-76.
2. Okushima, K., and Kakino, Y., 1972, “A Study of Residual Stress Produced by Metal Cutting,” Mem. Fac. Eng., Kyoto Univ., Jpn., 34, pp. 234-248.
3. Tsuchida, K., Kawada, Y., and Kodama, S., 1975, “A Study of the Residual Stress Distributions by Turning,” Bull. Jpn. Inst. Met., 18, pp. 123-130.
4. Liu, C. R., and Barash, M. M., 1982, “Variables Governing Patterns of Mechanical Residual Stress in a Machined Surface,” J. Eng. Ind. Trans. ASME, 104, pp. 257-264.
5. Matsumoto, Y., Barash, M. M., and Liu, C. R., 1986, “Effect of Hardness on the Surface Integrity of AISI 4340 Steel,” J. Eng. Ind. Trans. ASME, 108, pp. 169-175.
6. Merwin, J. E., and Johnson, K. L., 1963, “An Analysis of Plastic Deformation in Rolling Contact,” Proc. Inst. Mech. Eng., 177, pp. 676-690.
7. Wu, D. W., and Matsumoto, Y., 1990, “Effect of Hardness on Residual Stresses in Orthogonal Machining of AISI 4340 Steel,” J. Eng. Ind. Trans. ASME, 112, pp. 245-252.
8. Thomsen, E. G., Lapsley, J. T., and Grassi, R. C., 1953, “Deformation Work Absorbed by the Workpiece During Metal Cutting,” Trans. ASME, 75, pp. 591-603.
9. Jang, D. Y., and Seireg, A., 1990, “A Model for Predicting Residual Stresses in Metal Cutting,” Proceeding of the Japan International Tribology Conference, pp. 439-444.
10. Shih, A. J., 1995, “Finite Element Simulation of Orthogonal Metal Cutting,” J. Eng. Ind. Trans. ASME, 117, pp. 84-93.
11. Wiesner, C., 1992, “Residual Stresses after Orthogonal Machining of AISI 304: Numerical Calculation of the Thermal Component and Comparison with Experimental Results,” Metall. Trans. A, 23A, pp. 989-996.
12. Hsu, H.-C., 1992, “An Elasto-Viscoplastic Finite Element Model of Orthogonal Metal Cutting for Residual Stress Prediction,” Ph.D. thesis, North Carolina State University.
13. Morrow, D., 1982, “Stress-Strain Response of a Two-Bar Structure Subject to Cyclic Thermal and Steady Net Section Loads,” Master’s thesis, University of Illinois.
14. Johnson K. L., and Jefferis, J. A., 1963, “Plastic Flow and Residual Stresses in Rolling and Sliding Contact,” Proceeding of the Symposium on Fatigue in Rolling Contact, Institute of Mechanical Engineers, London, pp. 54-65.
15. Palmer, W. B., and Yeo, R. C. K., 1963, “Metal Flow Near the Tool Point During Orthogonal Cutting with a Blunt Tool,” Proceedings of the 4th International Machine Tool Design and Research Conference, Pergamon, Oxford, pp. 61-71.
16. Enahoro, H. E., and Oxley, P. L. B., 1966, “Flow Along Tool-Chip Interface in Orthogonal Metal Cutting,” J. Mech. Eng. Sci., 8, No. 1, pp. 36-41.
17. Taylor, G. I., and Quinney, H., 1934, “The Latent Energy Remaining in a Metal after Cold Work,” Proc. R. Soc. London, Ser. A, 145, pp. 362-387.
18. Sekhon, G. S., and Chenot, J. L., 1993, “Numerical Simulation of Continuous Chip Formation during Non-Steady Orthogonal Cutting,” Eng. Comput., 10, pp. 31-48.