Some guidelines on the use of profile reliefs of high contact ratio spur gears

Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science

Volumn 219, Issue 10, 2005, Pages 1087-1095

  Yildirim, N ^a  

^a GAZIANTEP UNIVERSITY   (Turkey)

Author keywords

Gear; Manucfacturing tolerance; Profile; Quality grade; Relief; Spur; Transmission error

Indexed keywords

COMPUTER SIMULATION; FITS AND TOLERANCES; GEAR MANUFACTURE; GEAR TEETH; NUMERICAL ANALYSIS; OPTIMIZATION; STIFFNESS; STRESSES;

MANUFACTURING TOLERANCE; PROFILE RELIEF; QUALITY GRADE; TOOTH STIFFNESS; TRANSMISSION ERROR;

SPUR GEARS;

GEAR;

EID: 28944440246     PISSN: 09544062     EISSN: None     Source Type: Journal    
DOI: 10.1243/095440605X31977     Document Type: Article

References (17)

1. Walker, H. Gear tooth deflection and profile modification. Engineer, 1938, 166, 409-412, 434-436.
2. Walker, H. Gear tooth deflection and profile modification. Engineer, 1940, 170, 102-104.
3. Harris, S. L. Dynamic loads on the teeth of spur gears. Proc. Instn Mech. Engrs, 1958, 172, 87-112.
4. Gregory, R. W., Harris, S. L., and Munro, R. G. Dynamic behaviour of spur gears. Proc. Instn Mech. Engrs, 1963-64, 178, 207-226.
5. Opitz, H. Noise of gears. Phil. Trans. Royal Soc., 1969, 263, 369-380.
6. Munro, R. G. Effect of geometrical errors on the transmission of motion between gears. Proc. Instn Mech. Engrs, 1969-70, 184, 79-84.
7. Niemann, G. and Baethge, J. Drehwegfehler, zahnfederhaerte und gerausch bei strnraedern. VDI-Z, 1970, 112(4), 205-214, and 112(8), 475-499.
8. Welbourn, D. B. Fundamental knowledge of gear noise - a survey. IMechE Conference on Noise and vibration of engines and transmissions, Cranfield, UK, 1979, 9-14.
9. Drago, R. J. How to design quiet transmissions. Mach. Des., 1980, 175-181.
10. Munro, R. G. and Yildirim, N. Some measurements of static and dynamic transmission errors of spur gears. In Proceedings of International Gearing Conference, Newcastle, UK, 1994.
11. Munro, R. G., Yildirim, N., and Hall, D. M. Optimum profile relief and transmission error in spur gears. lMechE First International Conference on Gearbox noise and vibration, 1990, 35-42.
12. Yildirim, N. and Munro, R. G. A systematic approach to profile relief design of low and high contact ratio spur gears. Proc. Instn Mech. Engrs, Part C: J. Mechanical Engineering Science, 1999, 213(C6), 551-562.
13. Yildirim, N. and Munro, R. G. A new type of profile relief for high contact ratio spur gears. Proc. Instn Mech. Engrs, Part C. J. Mechanical Engineering Science, 1999, 213(C6), 563-568.
14. Cheon, G. J. and Parker, R. G. Influence of manufacturing errors on the dynamic characteristics of planetary gear systems. KSME Int. J. 2004, 18(4), 606-621.
15. Driot, N., Rigaud, E., Sabot. J., and Perret-Liaudet, J. Allocation of gear tolerances to minimize gearbox noise variability. ACUSTICA 2001, 87(1), 67-76.
16. Cornell, R. W. Compliance and stress sensitivity of spur gear teeth. J. Mech. Design, Trans. ASME, 1981, 103, 447-459.
17. Yildirim, N. Theoretical and experimental research in high contact ratio spur gearing. PhD Thesis, University of Huddersfield, 1994.