Multi-operational machining processes modeling for sequential root cause identification and measurement reduction

Journal of Manufacturing Science and Engineering

Volumn 127, Issue 3, 2005, Pages 512-521

  Wang, Hui ^a   Huang, Qiang ^a   Katz, Reuven ^b  

^a University of South Florida   (United States)

^b UNIVERSITY OF MICHIGAN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

FIXTURES (TOOLING); FLEXIBLE MANUFACTURING SYSTEMS; MATHEMATICAL MODELS; PRODUCT DESIGN; PRODUCT DEVELOPMENT;

DESIGN SYNTHESIS; MEASUREMENT REDUCTION; ROOT CAUSE IDENTIFICATION;

MACHINING CENTERS;

EID: 24644516973     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1948403     Document Type: Article

References (22)

1. Fadale, T. D., Nenarokomov, A. V., and Emery, A. F., 1995, "Two Approaches to Optimal Sensor Locations," ASME Trans. J. Heat Transfer, 117, pp. 373-379.
2. Udwadia, F. E., 1994, "Methodology for Optimum Sensor Locations for Parameter Identification in Dynamic Systems," J. Eng. Mech., 102, pp. 368-390.
3. Wang, Y., and Nagarkar, S. R., 1999, "Locator and Sensor Placement for Automated Coordinate Checking Fixtures," ASME J. Manuf. Sci. Eng., 121, pp. 709-719.
4. Khan, A., Ceglarek, D., and Ni, J., 1998, "Sensor Location Optimization for Fault Diagnosis in Multi-Fixture Assembly Systems," ASME J. Manuf. Sci. Eng., 120, pp. 781-792.
5. Ding, Y., Kim, P., Ceglarek, D., and Jin, J., 2003, "Optimal Sensor Distribution for Variation Diagnosis for Multi-Station Assembly Processes," IEEE Trans. Rob. Autom., 19, pp. 529-542.
6. Ding, Y., Gupta, A., and Apley, D. W., 2004, "Singularity Issues in Fixture Fault Diagnosis for Multi-Station Assembly Process," ASME J. Manuf. Sci. Eng., 126, pp. 200-210.
7. Lawless, J. F., Mackay, R. J., and Robinson, J. A., 1999, "Analysis of Variation Transmission in Manufacturing Process-Part I," J. Quality Technol., 31, pp. 131-142.
8. Lawless, J. F., Mackay, R. J., and Robinson, J. A., 1999, "Analysis of Variation Transmission in Manufacturing Process-Part II," J. Quality Technol., 31, pp. 143-154.
9. Jin, J., and Shi, J., 1999, "State Space Modeling of Sheet Metal Assembly for Dimensional Control," ASME J. Manuf. Sci. Eng., 121, pp. 756-762.
10. Ding, Y., Ceglarek, D., and Shi, J., 2000, "Modeling and Diagnosis of Multistage Manufacturing Processes: Part I: State Space Model," Japan/USA Symposium on Flexible Automation, Ann Arbor, MI, 23-26 July.
11. Huang, Q., Shi, J., and Yuan, J., 2003, "Part Dimensional Error and Its Propagation Modeling in Multi-Operational Machining Process," ASME J. Manuf. Sci. Eng., 125, pp. 255-262.
12. Also appeared in Proc. 2000 ASME Int. Mech. Eng. Congress and Exposition, 5-10 November, Orlando, FL, MED- Vol. 11, pp. 81-88.
13. Djurdjanovic, D., and Ni, J., 2001, "Linear State Space Modeling of Dimensional Machining Errors," Trans. NAMRC/SME, XXIX, pp. 541-548.
14. Zhou, S., Huang, Q., and Shi, J., 2003, "State Space Modeling of Dimensional Variation Propagation in Multistage Machining Process Using Differential Motion Vectors," IEEE Trans. Rob. Autom., 19, pp. 296-309.
15. Huang, Q., and Shi, J., 2004, "Stream of Variation Modeling and Analysis of Serial-Parallel Multistage Manufacturing Systems," (in press).
16. Mantripragada, R., and Whitney, D., 1999, "Modeling and Controlling Variation Propagation in Mechanical Assemblies Using State Transition Models," IEEE Trans. Rob. Autom., 15, pp. 124-140.
17. Zhou, S., Yu, D., Chen, Y., and Shi, J., 2003, "Diagnosability Study of Multistage Manufacturing Process Based on Linear Mixed-Effects Models," Technometrics, 45, pp. 312-325.
18. Huang, Q., and Shi, J., 2004, "Variation Transmission Analysis and Diagnosis of Multi-Operational Machining Processes," IIE Trans., Qual. Reliab. Eng., 36, pp. 807-815.
19. Huang, Q., and Shi, J., 2003, "Simultaneous Tolerance Synthesis through Variation Propagation Modeling of Multistage Manufacturing Processes," Trans. NAMRC/SME, XXXI, pp. 515-522.
20. Martinsen, K., 1993, "Vectorial Tolerancing for All Types of Surfaces," ASME Conferences, Adv. Des. Autom., 2, pp. 187-198.
21. Cai, W., Hu, S., and Yuan, J., 1996, "A Variational Method of Robust Fixture Configuration Design for 3-D Workpiece," ASME J. Manuf. Sci. Eng., 119, pp. 593-602.
22. Chen, J. S., Yuan, J. X., Ni, J., and Wu., S. M., 1993, "Real-Time Compensation for Time-Variant Volumetric Errors on a Machining Center," ASME J. Eng. Ind., 115, pp. 472-479.