Burr formation in face milling of cast iron with different milling cutter systems

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 217, Issue 11, 2003, Pages 1589-1596

  De Souza Junior A M ^a   Sales, W F ^b   Ezugwu, E O ^c   Bonney, J ^c   Machado, A R ^d  

^a Fiat GM Powertrain Ltd   (Brazil)

^b Pont Univ Catol de MG   (Brazil)

^c LONDON SOUTH BANK UNIVERSITY   (United Kingdom)

^d FEDERAL UNIVERSITY OF UBERLÂNDIA   (Brazil)

Author keywords

Burr formation; Milling cutter system; PCBN tools; Surface finish; Tool wear

Indexed keywords

CAST IRON; CUBIC BORON NITRIDE; CUTTING; SURFACE ROUGHNESS;

BURR FORMATION; FACE MILLING;

MILLING (MACHINING);

EID: 0346959718     PISSN: 09544054     EISSN: None     Source Type: Journal    
DOI: 10.1243/095440503771909962     Document Type: Conference Paper

References (13)

1. Tool wear in the cutting of thin-gauge steel sheets. ASTME Research Report 22, American Society of Tool and Manufacturing Engineers, Dearborn, Michigan, 1959.
2. Dornfeld, D. A. Integrated designs and manufacturing for milling burr minimization. Research Reports by CODEF, Laboratory for Manufacturing Automation, University of California, Berkeley, 1998.
3. Gillespie, L. K. and Blotter, P. T. The formation and properties of machining burrs. Trans. ASME, 1976, 98, 66-74.
4. Nakayama, K. and Arai, M. Burr formation in metal cutting. Ann. CIRP, 1987, 36, 33-36.
5. Pekelharing, A. J. The exit failure uninterrupted cutting. Ann. CIRP, 1978, 27(1), 5-10.
6. Hashimura, M., Chang, Y. P. and Dornfeld, D. A. Analysis of burr formation mechanism in orthogonal cutting. J. Mfg Sci. Engng, 1999, 121, 1-7.
7. Ko, S. L. and Dornfeld, D. A. Analysis of fracture in burr formation at the exit stage of metal cutting. J. Mater. Processing Technol., 1996, 58, 189-200.
8. Ko, S. L. and Dornfeld, D. A. Burr formation and fracture in oblique cutting. J. Mater. Processing Technol., 1996, 63, 24-36.
9. Chern, G. L. and Dornfeld, D. A. Burr/breakout model development and experimental verification. J. Engng Mater. Technol., 1996, 118, 201-206.
10. Trent, E. M. Metal Cutting, 3rd edition, 1991, 273 pp. (Butterworths-Heinemann, London).
11. Olvera, O. and Barrow, G. Influence of exit angle and tool nose geometry on burr formation in face milling operations. Proc. Instn Mech. Engrs, Part B: J. Engineering Manufacture, 1998, 212(B1), 59-72.
12. Lee, M., Horne, J. G. and Tabor, D. The mechanism of notch formation at the depth of cut line of ceramic tools when machining nickel base superalloys. In Proceedings of International Conference on Wear Materials, ASME, Dearborn, Michigan, 16-18 April 1979, pp. 460-469.
13. Mills, B. and Redford, A. H. Machinability of Engineering Materials, 1983 (Applied Science Publications, London).