Influence of exit angle and tool nose geometry on burr formation in face milling operations

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 212, Issue 1, 1998, Pages 59-72

  Olvera, O ^a   Barrow, G ^a  

^a UNIVERSITY OF MANCHESTER   (United Kingdom)

Author keywords

Burrs; Exit angle; Milling; Nose geometry

Indexed keywords

CARBON STEEL; METAL CUTTING; PERFORMANCE; SURFACE ROUGHNESS; TOOLS;

FACE MILLING;

MILLING (MACHINING);

EID: 0031653291     PISSN: 09544054     EISSN: None     Source Type: Journal    
DOI: 10.1243/0954405981515509     Document Type: Article

References (17)

1. Kishimoto, W., Miyake, T., Yamamoto, A., Yamanaka, K. and Takano, K. Study of burr formation in face milling. Bull. Jap. Soc. Prec. Engng, 1981, 15(1), 51-52.
2. Chern, G. L. Analysis of burr formation and breakout in metal cutting. PhD thesis, Department of Mechanical Engineering, University of California in Berkeley, 1993.
3. Olvera, O. and Barrow, G. An experimental study of burr formation in square shoulder face milling. Int. J. Mach. Tools Mf., 1996, 36(9), 1005-1020.
4. Schafer, F. Product design influences on deburring. MR75-483, SME paper, 1975.
5. Pekelharing, A. J. The exit failure in interrupted cutting. Ann. CIRP, 1978, 27(1), 5-10.
6. Chern, G. L. and Dornfeld, D. A. Burr/breakout model development and experimental verification. Trans. ASME, J. Engng Mater. Technol., 1996, 118, 201-206.
7. Ko, S. L. and Dornfeld, D. A. A study on burr formation mechanism. Trans. ASME, J. Engng Mater. Technol., 1991, 113, 75-87.
8. Ko, S. L. and Dornfeld, D. A. Analysis of fracture in burr formation at the exit stage of metal cutting. J. Mater. Process. Technol., 1996, 58, 189-200.
9. Kamaruddin, A.G. Tool life in interrupted cutting. PhD thesis. Department of Mechanical Engineering, University of Manchester Institute of Science and Technology, 1984.
10. Gillespie, L. K. Burrs produced by end-milling. BDX-613-1503, Bendix Report, Bendix Co., Kansas City Division, 1976.
11. Gillespie, L. K. The measurement of burrs. MR74-993, SME technical paper, 1974.
12. Pekelharing, A. J. The exit failure of cemented carbide face milling cutters, part I - fundamentals and phenomena. Ann. CIRP, 1984, 33(1), 47-50.
13. Beachem, C. D. The effects of crack tip plastic flow directions upon microscopic dimple shapes. Metall. Trans., 1975, 6A, 377-383.
14. Colwell, L. V. Predicting the angle of chip flow for single point cutting tools. Trans. ASME, 1954, 16, 199-204.
15. Okushima, K. and Minato, K. On the behaviour of chip in steel cutting. Bull. Jap. Soc. Mech. Engrs, 1959, 2(5), 58-64.
16. Spaans, C. A systematic approach to three-dimensional chip curl, chipbreaking and chip control. MR70-241, SME technical paper, 1970.
17. Young, H. T., Mathew, P. and Oxley, P. L. B. Allowing for nose radius effects in predicting the chip flow direction and cutting forces in bar turning. Proc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 1987, 201(C3), 213-226.