Burr/breakout model development and experimental verification

Journal of Engineering Materials and Technology, Transactions of the ASME

Volumn 118, Issue 2, 1996, Pages 201-206

  Chern, Gwo Lianq ^a   Dornfeld, David A ^b  

^a NATIONAL YUNLIN UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

^b UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ALUMINUM ALLOYS; COPPER; CRACK PROPAGATION; DEBURRING; DEFORMATION; ESTIMATION; FRACTURE; IMPACT TESTING; MATERIALS TESTING; MATHEMATICAL MODELS; MICROMACHINING; SCANNING ELECTRON MICROSCOPY;

BURR FORMATION MODELING; MICROMACHINING TESTS; ORTHOGONAL CUTTING; PLASTIC BENDING; PLASTIC SHEARING; STRAIN ANALYSIS;

CUTTING;

EID: 0030127511     PISSN: 00944289     EISSN: 15288889     Source Type: Journal    
DOI: 10.1115/1.2804887     Document Type: Article

References (14)

1. Chern, G. L., 1993, “Analysis of Burr Formation and Breakout in Metal Cutting,” Ph.D. dissertation, Univ. of California, Berkeley, Department of Mechanical Engineering, May.
2. Datsko, J., 1967, Material Properties and Manufacturing Process, Wiley, New York.
3. Gillespie, K. L., 1979, “Deburring Precision Miniature Parts” Precision Engineering, vol. 1, No, 4, pp. 189-198.
4. Gillespie, K. L., and Blotter, P. T., 1976, “The Formation and Properties of Machining Burr,” ASME Journal Engineering for Industry, vol. 98, No. 1, pp. 66-74.
5. Iwata, K., Ueda, K., and Okuda, K., 1982, “Study of Mechanism of Burrs Formation in Cutting Based on Direct SEM Observation,” J. Soc. Free. Eng., vol. 48-4, pp. 510-515.
6. Ko, S. L., 1989, “Burr Formation and Fracture Mechanism at the Exit Stage of Machining Metals,” Ph.D. dissertation, Univ. of California, Berkeley, Department of Mechanical Engineering, Nov.
7. Ko, S. L., and Domfeld, D. A., 1991, “A Study on Burr Formation Mechanism,” ASME JOURNAL ENGINEERING MATERIALS TECHNOLOGY, vol. 113, pp. 75-87.
8. Kobayashi, S., Herzog, R. P., Eggleston, D. M., and Thomsen, E. G., 1960, “A Critical Comparison of Metal Cutting Theories with New Experimental Data,” ASME Journal Engineering for Industry, vol, 82, No. 4, pp. 333-347.
9. Komanduri, R., Hayashi, S. R., Fielding, J. O., and Bolon, R. B., 1980, “A Specimen Stage for In Situ Orthogonal Machining Studies Inside the SEM,” Tech. Inform. Series, Report No. 80CRD071, General Electric Co. Research Center, New York, May.
10. Merchant, M. E., 1945, “Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type-2 chip,” 7. of Applied Physics, vol, 16, No. 5, pp. 267-275.
11. Nakayama, K., and Arai, M., 1987, “Burr Formation in Metal Cutting,” Annals of the CIRP, vol. 36, No. 1, pp. 33-36.
12. RamalingAm. S., and Bell, A. C., 1973, “A Scanning Electron Microscope for the Observation of Chip Formation,” Review Science Instrum., vol. 44, No. 5, pp. 573-576.
13. Stiles, T. A., 1985, “A Scanning Electron Microscope (SEM) Machining Substage for Metal Cutting Observation and Acoustic Emission Analysis,” MS thesis, Univ. of California, Berkeley, Department of Mechanical Engineering.
14. Wright, P. K., 1982, “Predicting the Shear Plane Angle in Machining from Workmateriai Strain-Hardening Characteristics,” ASME Journal Engineering for Industry, vol. 104, No. 3, pp. 285-292.