Tool geometry study in micromachining

Journal of Micromechanics and Microengineering

Volumn 13, Issue 5, 2003, Pages 726-731

  Fang, F Z ^a   Wu, H ^a   Liu, X D ^a   Liu, Y C ^a   Ng, S T ^a  

^a SINGAPORE INSTITUTE OF MANUFACTURING TECHNOLOGY   (Singapore)

Author keywords

[No Author keywords available]

Indexed keywords

BRASS; COMPUTER SIMULATION; DYNAMOMETERS; FAILURE (MECHANICAL); FINITE ELEMENT METHOD; HARDNESS; MACHINE TOOLS; MICROMACHINING; MILLING (MACHINING); RIGIDITY; SERVICE LIFE; TUNGSTEN CARBIDE;

END MILLS; MICRO PARTS; TOOL BREAKAGE; TOOL FAILURE; TOOL GEOMETRY; TOOL TIP RIGIDITY;

MICROELECTROMECHANICAL DEVICES;

EID: 0141718769     PISSN: 09601317     EISSN: None     Source Type: Journal    
DOI: 10.1088/0960-1317/13/5/327     Document Type: Article

References (16)

1. Masuzawa T 2000 State of the art of micromachining Ann. CIRP 49 473
2. Kussul E, Baidyk T, Ruiz-Huerta L, Caballero-Ruiz A, Velasco G and Kasatkina L 2002 Development of micromachine tool protypes for microfactories J. Micromech. Microeng. 12 795
3. Weule H, Huntrup V and Tritschler H 2001 Micro-cutting of steel to meet new requirements in miniaturization Ann. CIRP 50 61
4. Tansel I, Rodriguez O, Trujillo M, Paz E and Li W 1998 Micro-end-milling: I. Wear and breakage Int. J. Machine Tools Manufacture 38 1419
5. Masuzawa T and Tonshoff H K 1997 Three-dimensional micromachining by machine tools Ann. CIRP 46 621
6. Friedrich C R, Coane P J and Vasile M J 1997 Micromilling development and applications for microfabrication J. Microelectron. Eng. 35 367
7. Brinksmeier E, Preuss W and Schmotz J 1997 Manufacture of microstructures by diamond machining Proc. 9th Int. Prec. Eng. Seminar and 4th Int. Conf. on Ultraprecision in Manuf. Eng. (Braunschweig) p 503
8. Corbett J, McKeown P A, Peggs G N and Whatmore R 2000 Nanotechnology: international development and emerging products Ann. CIRP 59 523
9. Schmidt J, Tritschler H and Haberer K 2001 Cutting tools and material conditioning for micro end milling of tool steel Proc. 2nd Euspen Int. Conf. (Turin, Italy) p 624
10. Bao W Y and Tansel I N 2000 Modeling micro-end-milling operations. Part II: tool run-out Int. J. Machine Tools Manufacture 40 2175
11. Fang F Z 2002 Cutting edge effect in micromachining Presentation to the Cutting Committee Meeting (Part II) in 52nd CIRP General Assembly (Spain)
12. http://www.generalcarbide.com/grades/
13. Juvinall R C 1967 Stress, Strain, and Strength (New York: McGraw-Hill) p 65
14. Trent E M 1984 Metal Cutting (Boston: Butterworths) p 118
15. Shaw M C 1989 Metal Cutting Principles (Oxford: Oxford University Press) p 102
16. Schaller T, Bohn L, Mayer J and Schubert K 1999 Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills Precision Eng. 23 229