Effect of acetabular modularity on polyethylene wear and osteolysis in total hip arthroplasty

Journal of Bone and Joint Surgery

Volumn 84, Issue 1, 2002, Pages 58-63

  Young, Anthony M ^a   Sychterz, Christi J ^a   Hopper, Robert H ^a   Engh, Charles A ^a  

^a ANDERSON ORTHOPAEDIC RESEARCH INSTITUTE   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

POLYETHYLENE;

ARTICLE; COMPUTER ANALYSIS; CONTROLLED STUDY; ENDOPROSTHESIS LOOSENING; FEMUR HEAD; HUMAN; LINEAR REGRESSION ANALYSIS; MAJOR CLINICAL STUDY; OSTEOLYSIS; PRIORITY JOURNAL; SURFACE PROPERTY; TOTAL HIP PROSTHESIS;

EID: 0036054774     PISSN: 00219355     EISSN: None     Source Type: Journal    
DOI: 10.2106/00004623-200201000-00009     Document Type: Article

References (30)

1. The problem is osteolysis
2. Increasing incidence of femoral osteolysis in association with uncemented Harris-Galante total hip arthroplasty. A follow-up report
3. Severe osteolysis of the pelvis in association with acetabular replacement without cement
4. Patterns of osteolysis around total hip components inserted with and without cement
5. An investigation into the origins of time-dependent variation in penetration rates with Charnley acetabular cups-wear, creep or degradation?
6. Reactions of the articular capsule to wear products of artificial joint prostheses
7. Factors contributing to rapid wear and osteolysis in hips with modular acetabular bearings made of hylamer
8. Radiographic evaluation of penetration by the femoral head into the polyethylene liner over time
9. Analysis of temporal wear patterns of porous-coated acetabular components: Distinguishing between true wear and so-called bedding-in
10. Determination of polyethylene wear in total hip replacements with use of digital radiographs
11. Two-dimensional versus threedimensional radiographic measurements of polyethylene wear
12. The Long-term results of low-friction arthroplasty of the hip performed as a primary intervention
13. Fractures through cystic lesions of the greater trochanter. A cause of late pain after cementless total hip arthroplasty
14. The effect of conformity, thickness, and material on stresses in ultra-high molecular weight components for total joint replacement
15. The role of backside polishing, cup angle, and polyethylene thickness on the contact stresses in metal-backed acetabular components
16. Backside nonconformity and locking restraints affect liner/shell load transfer mechanisms and relative motion in modular acetabular components for total hip replacement
17. The effect of UHMWPE liner geometry on micromotion
18. Motion at the modular acetabular shell and liner interface
19. Fixation of ultrahigh-molecular-weight polyethylene liners to metal-backed acetabular cups
20. Simulation of initial frontside and backside wear rates in a modular acetabular component with multiple screw holes
21. Polyethylene and metal debris generated by non-articulating surfaces of modular acetabular components
22. The relationship between the design, position, and articular wear of acetabular components inserted without cement and the development of pelvic osteolysis
23. The Otto Aufranc Award. Impact of gamma sterilization on clinical performance of polyethylene in the hip
24. Three-dimensional polyethylene wear of a press-fit titanium prosthesis. Factors influencing generation of polyethylene debris
25. Effect of acetabular component orientation on recurrent dislocation, pelvic osteolysis, polyethylene wear, and component migration
26. Shelf life and in vivo duration. Impacts on performance of tibial bearings
27. Technique for acetabular liner revision in a nonmodular metal-backed component
28. Radiological demarcation of cemented sockets in total hip replacement
29. Modes of failure of cemented stemtype femoral components. A radiographic analysis of loosening