Simulation of diesel engines cold-start

SAE Technical Papers

Volumn , Issue , 2003, Pages

  Liu, Hengqing ^a   Henein, N A ^b   Bryzik, Walter ^c  

^a GENERAL MOTORS CORPORATION   (United States)

^b WAYNE STATE UNIVERSITY   (United States)

^c AMSRD TAR R MS 264   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMBUSTION CHAMBERS; DIRECT INJECTION; ENGINE CYLINDERS; FUELS; STARTING;

COMBUSTION CHAMBER WALLS; COMBUSTION INSTABILITIES; COMPUTER SIMULATION MODEL; DIESEL ENGINE COMBUSTIONS; DIRECT INJECTION DIESEL ENGINES; INSTANTANEOUS ENGINE SPEED; NATURALLY ASPIRATED; STEADY STATE AND TRANSIENTS;

DIESEL ENGINES;

EID: 85072447122     PISSN: 01487191     EISSN: 26883627     Source Type: Journal    
DOI: 10.4271/2003-01-0080     Document Type: Conference Paper

References (28)

1. Liu, Z., and Karim, G. A., "An examination of the role of residual gases in the combustion processes of motored engines fuelled with gaseous fuels" SAE Paper 961087, 1996.
2. Kwon, S., and Aral, M., "Ignition delay of a diesel spray injected into a residual gas mixtures" SAE Paper 911841, 1991.
3. Hardenberg, H. O., and Hase, F. W., "An Empirical Formula for Computing the Pressure Rise Delay of a Fuel From its Cetane Number and from Relevant Parameters of Direct-Injection Diesel Engines" SAE Paper 790493, 1979.
4. Clerc, J. C., "Cetane number requirements of light-duty diesel engines at low temperatures" SAE Paper 861525, 1986.
5. Hara, H., Itoh, Y., Henein, N. A., and Bryzik, W., "effect of cetane number with and without additive on cold startability and white smoke emissions in a diesel engine" SAE Paper 1999-01-1476, 1999.
6. Austen, W., and Lyn, W. T., "Some investigations on cold starting phenomena in diesel engines" SAE Paper no. 5, 1959-60.
7. Phatak, R. E., and Nakamura, T., "Cold startability of open-chamber direct-injection diesel engines-part I Measurement technique and effects of compression ratio" SAE Paper 831335, 1983.
8. Osuka, I., and Nishimura, M., "Benefits of new fuel injection system technology on cold startability of diesel engines-improvement of cold startability and white smoke reduction by means of multi injection with common rail fuel system (ECD-U2)" SAE Paper 940586, 1994.
9. Tsunemoto, H., Yamada, T., and Ishitani, H., "Behavior of adhering fuel on cold combustion chamber wall in direct injection diesel engines" SAE Paper 861235, 1986.
10. Biddulph, T. W., Lyn, W. T., "Unaided starting of diesel engines" Proc. Inst. Mech. Engrs., Vol. 181, 1966-67.
11. Gardner, T. P., "Optimization of compression ratio in compression ignition engines" Ph.D. dissertation, 1986.
12. Liu, Hengqing, Chalhoub, N., and Henein, N. A., "Simulation of a single cylinder diesel engine under cold start conditions using Simulink" Advanced Engine Simulations vol. 1, ICE-Vol. 28-1, 1997.
13. Borman, G. L., and Johnson, J. H., "Unsteady vaporization histories and trajectories of fuel drops injected into swirling air" SAE Paper 598C, 1962.
14. Tanasawa, Y., and Hiroyasu, H., "On the drop size analyzer for liquid spray by sedimentation" Tech. Rep. Of Tohoku University, 27-1, 1962, 67.
15. Hiroyasu, H., and Kadota, T., "Fuel droplet size distribution in diesel combustion chamber" SAE Paper 740715, 1974.
16. Gupta, S., Poola, R., and Sekar, R., "Effect of injection parameters on diesel spray characteristics" SAE Paper 2000-01-1600, 2000.
17. Incropera, F. P., and Dewett, D. P., "Fundamentals of heat and mass transfer" 3rd edition, 1990, pp 356.
18. Reid, and Sherwood, "The properties of gases and liquids" 2nd edition, 1966.
19. Henein, N. A., "Performance of diesel injection systems with alternative fuels Part 1: physical properties" Technical Report, 1987.
20. Petris, C. D., Giglio, V., and Police, G., "A mathematical model of the evaporation of the oil film deposed on the cylinder surface of IC engines" SAE paper 972920, 1997.
21. Stanton, D. W., Rutland, C.J., "Multi-dimensional modeling of heat and mass transfer of fuel films resulting from impinging sprays" SAE Paper 980132, 1998.
22. Zahdeh, A. R., Henein, N. A., and Bryzik, W., "Diesel cold starting: actual cycle analysis under border-line conditions" SAE Paper 900441, 1990.
23. Henein, N. A., and Bryzik, W., "Diesel engine cold starting: combustion instability" SAE Paper 920005, 1992.
24. Bryzik, W., and Henein, N. A., "Fundamental cold start phenomena within advanced military diesel engines" Army Science conference proceedings, vol. III, 1994.
25. Meyer, W. E., and Decarolis, J. J., "Compression Temperatures in Diesel Engines under Starting Conditionsn, SAE Trans., 1962, pp. 163-174.
26. Henein, N. A., "Starting of diesel engines: Uncontrolled fuel injection problems" SAE Paper 860253, 1986.
27. Han, Zhiping, Henein, N. A., and Bryzik, W., "A New Ignition Delay Correlation with Predictions of Diesel Engine Cold Start Misfiring" SAE Paper, 2000-01-1184, 2000.
28. Igura, S., Kadota, T., and Hirozasu, H., "Spontaneous Ignition Delay of Fuel Sprays in High Pressure Gaseous Environment," Jap. Soc. Mech. Engrs., Vol. 41, No. 345, p. 1559, 1975.