Analysis of droplet spreading on a rotating surface and the prediction of cooling and lubrication performance of an atomization-based cutting fluid system

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 135, Issue 3, 2013, Pages 1-12

  Ghai, Isha ^a   Samuel, Johnson ^a   DeVor, Richard E ^a   Kapoor, Shiv G ^a  

^a University of Illinois at Urbana Champaign   (United States)

Author keywords

Atomization; Cooling; Cutting fluid; Droplet; Lubrication; Micromachining; Rotating surface; Spreading

Indexed keywords

EID: 84994023689     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4024153     Document Type: Article

References (17)

1. Jun, M. B., Joshi, S. S., DeVor, R. E., and Kapoor, S. G., 2008, “An Experimental Evaluation of an Atomization-Based Cutting Fluid Application System for Micromachining,” ASME J. Manuf. Sci. Eng., 130(3), p. 031118.
2. Ghai, I., Wentz, J., DeVor, R. E., Kapoor, S. G., and Samuel, J., 2010, “Droplet Behavior on a Rotating Surface for Atomization-Based Cutting Fluid Application in Micromachining,” ASME J. Manuf. Sci. ting., 132(1), p. 011017.
3. Attane, P., Girard, F., and Morin, V., 2007, “An Energy Balance Approach of the Dynamics of Drop Impact on a Solid Surface,” Phys. Fluids, 19, p. 012101.
4. Bechtel, S. E., Bogy, D. B., and Talke, F. E., 1981, “Impact of Liquid Drop Against a Flat Surface,” IBM J. Res. Dev., 25(6), pp. 963-971.
5. Mao, T., Kuhn, D. C. S., and Tran, H., 1997, “Spread and Rebound of Liquid Droplets Upon Impact on Flat Surfaces,” AlChE J., 43(9), pp. 2169-2179.
6. Lim, T., Han, S., Chung, J., Chung, J. K., Ko, S., and Grigoropoulos, C. P., 2009 “Experimental Study on Spreading and Evaporation of Inkjet Printed Pico-Liter Droplet on a Heated Substrate,” Int. J. Heat Mass Transfer, 52, pp. 431-441.
7. Adair, K. G., 2009, “Development of a Unique Topology for a Hard Turning Micro-Scale Machine Tool,” M.S. thesis, University of Illinois at Urbana- Champaign, Urbana, 1L.
8. Ellicott, G. J., DeVor, R. E., and Kapoor, S. G., 2009, “Machinability Investigation of Micro-Scale Hard Turning of 52100 Steel,” North Am. Manuf. Res. Inst. SME, 37, pp. 143-150.
9. Chandra, S., Di Marzo, M., Qiao, Y. M., and Tartarini, P., 1996, “Effect of Liquid-Solid Contact Angle on Droplet Evaporation,” Fire Saf. J., 27, pp. 141-158.
10. Wang, C. Y., 1973, “Axi symmetric Stagnation Point Flow Over a Moving Plate,” AlChE J., 19, pp. 1080-1081.
11. Chandra, S., and Avedisian, C. T., 1991, “On the Collision of a Droplet With a Solid Surface,” Proc. R. Soc. London, 432, pp. 13-41.
12. Schiafftno, S., and Sonin, A. A., 1997, “Molten Droplet Deposition and Solidification at Low Weber Numbers,” Phys. Fluids, 9(11), pp. 3172-3187.
13. Tio, K. K., and Sadhal, S. S., 1992, “Dropwise Evaporation—Thermal Analysis of Multidrop Systems,” Int. J. Heat Mass Transfer, 35(8), pp. 1987-2004.
14. Walklate, P. J., Weiner, K. L., and Parkin, C. S., 1996, “Analysis of and Experimental Measurements Made on a Moving Air-Assisted Sprayer With Two-Dimensional Air-Jets Penetrating a Uniform Crop Canopy,” J. Agric. ting. Res., 63(4), pp. 365-377.
15. Rukosuyev, M., Goo, C. S., Jun, M. B. G., and Park, S. S., 2010, “Design and Development of Cutting Fluid System Based on Ultrasonic Atomization for Micro-Machining,” North Am. Manuf. Res. Inst. SME, 38, pp. 97-104.
16. Langlois, W. E., 1965, “A Wedge-Flow Approach to Lubrication Theory,” Q. Appl. Math., 23(1), pp. 39-45.
17. Dobre, M., and Bolle, L., 2002, “Practical Design of Ultrasonic Spray Devices: Experimental Testing of Several Atomizer Geometries,” Exp. Therm. Fluid Sci., 26(2), pp. 205-211.