Tribological performance of lubricating oil contaminated with fine dust particles

SAE Technical Papers

Volumn 2014-January, Issue , 2014, Pages

  Mohan, Nishant ^a   Sharma, Mayank ^a   Singh, Ramesh ^a   Kumar, Naveen ^a  

^a DELHI TECHNOLOGICAL UNIVERSITY   (India)

Author keywords

[No Author keywords available]

Indexed keywords

COMMERCIAL VEHICLES; CONTAMINATION; FRICTION; IMPURITIES; INTERNAL COMBUSTION ENGINES; LUBRICATING OILS; TRIBOLOGY; WEAR OF MATERIALS;

CIRCULAR SURFACES; COEFFICIENT OF FRICTIONS; CONSTRUCTION SITES; FRICTION AND WEAR; PIN ON DISK SETUP; RELATIVE MOTION; THIRD BODY EFFECTS; TRIBOLOGICAL PERFORMANCE;

DUST;

EID: 84938152500     PISSN: None     EISSN: 01487191     Source Type: Journal    
DOI: 10.4271/2014-01-2334     Document Type: Conference Paper

References (48)

1. Daniels, C.C., and Braun, M.J., " The Friction Behavior of Individual Components of a Spark-Ignition Engine During Warm-Up," Tribology Transactions Vol. 49, Iss. 2, 2006.
2. http://prius.ecrostech.com/original/Understanding/InternalCombustion.htm, accessed on 4 th April, 2014.
3. Pinkus, O., Wilcock, D.F., " Strategy for energy conservation through tribology," New York: ASME, 1977.
4. Lang, O.R., " Reibungsverluste in Verbrennungs motoren (Friction losses in engines)." Tribologie und Schmierungs technik 1982; 29: 90-2.
5. Andersson, B.S., " Paper XVIII (III) Company perspectives in vehicle tribology Volvo," Vehicle Tribology Amsterdam: Elsevier Publications; 991: 503-6.
6. Bartz, W.J., " Fuel economy improvement in engine and gear oils," 24th Leeds-Lyon symposium on tribology, tribology for energy conservation, London, UK, Elsevier Series 34. Amsterdam, Netherlands, Elsevier; September 4-6, 1998, 13-24.
7. Taylor, R.I., " Engine friction lubricant sensitivities: a comparison of modern diesel and gasoline engines," 11th international colloquium on industrial and automotive lubrication. Esslingen, Germany: Technishe Academie Esslingen, 1998.
8. van Basshuysen and Schäfer, F., " Internal Combustion Engine Handbook," Society of Automotive Engineers, Inc., Warrendale, PA, ISBN 978-0-7680-1139-5, 2004, doi: 10.4271/R-345.
9. Tung, S.C., and McMillan, M.L., " Automotive tribology overview of current advances and challenges for the future," Tribology International 37: 517-36, 2004.
10. Hikita, Y., Yamazaki, M., Natsume, J., Shimura, T., et al., " Development of crankshaft bearing with an eccentric oil groove," International tribology conference, Kobe, Japan, paper ID-02, 24, 2005.
11. " Tires and passenger vehicle fuel economy informing consumers, improving performance," National Research Council of the National Academies, Washington DC, Transportation Research Board, Special Report 286; 2006.
12. " National Research Council of the National Academies. " Assessment of fuel economy technologies for light-duty vehicles. Washington DC, National Academies Press; 2011.
13. Jost, P., " Tribology micro & macroeconomics: a road to economic savings," 3rd world tribology congress, Washington DC, September 13, 2005.
14. Andersson, B.S., " Company Perspectives in Vehicle Tribology, Volvo " in 17th Leeds-Lyon Symposium on Tribology, Vehicle Tribology, Tribology Series, Vol. 18, Elsevier Science, Oxford UK, 503-506.
15. Mang T., Dresel, W., " Lubricants and Lubrication," Wiley-VCH, Weinheim, 2001.
16. Adhvaryu, A., Liu, Z.S., and Erhan, S.Z., " Industrial Crops and Products," 21: 113-119, 2005.
17. Woldman, M., van der Heide, E., Schipper, D.J., Tinga, T. et al., " Investigating the influence of sand particle properties on abrasive wear behavior," Wear 294-295: 419-426, 2012, doi: 10.1016/j.wear.2012.07.017.
18. Li, C., and Yan, F., " Abrasive Wear Behavior of Several Metallic Materials under Simulated Sand-Dust Environment," Proceedings of CIST 2008 & ITS-IFToMM 283-284, 2008, doi: 10.1007/978-3-642-03653-8-88.
19. Qi, J., Wang, L., Yan, F., and Xue, Q., " Ultra-high tribological performance of magnetron sputtered a-C:H films in sand-dust environment," Tribology. Letters 38: 195-205, 2010.
20. Qi, J., Wang, L., Yan, F., and Xue, Q., " Comparative study of microstructure and tribological behavior of TiC/a-C:H and a-C:H coatings in a sand-dust environment," Surf. Interface Anal. 43: 836-846, 2011.
21. Fuhs, S. and Harrris, J., " Dust protection for environmental control and life support systems in the lunar environment," Lunar Materials Technology Symposium, 1992.
22. Rickman, D., and Street, K.W., " Some Expected Mechanical Characteristic of Lunar Dust: A Geological View," 2008, NASA NTRS Document ID: 20080006059.
23. Fuhs, S., and Harrris, J., " Dust protection for environmental control and life support systems in the lunar environment. " Lunar materials technology symposium, 1992.
24. Schmitt, H., " The Apollo experience/problems encountered with lunar dust," Biological effects of Lunar dust workshop, Sunnyvale, CA, 2005.
25. Goodwin, R.A., " The NASA Mission Reports," Vol. 1, Apogee Books, Ontario, Canada, 2002.
26. Heiken, G.H., Vaniman, D.T., French, B.M., " Lunar source book: auser's guide to the Moon," Cambridge University Press, 1991.
27. Gaier, J.R., " The effects of Lunar dust on EVA systems during the Apollo Missions," NASA/TM 2005-213610/REV1.
28. Jianwei, Q., Hongtao, L., Yong, L., Dekun., et al. " Influences of added sand-dust particles on the tribological performance of graphite-like coating under solid-liquid lubrication," Tribology International 71: 69-81, 2014.
29. Chotěborsky, R., Hrabě P., Muller, M., Savkova, J., et al., " Effect of abrasive particle size on abrasive wear of hard facing alloys," Res. Agric. Eng. 55 (3): 101-113, 2009.
30. Eyre, T.S., " Wear characteristics of metals," Tribol. Int. 10: 203-212, 1976, doi: 10.1016/0301-679X(76)90077-3.
31. Kragel'skii, I. V., Dobychin, M. N., and Kombalov, V. S., " Principles of Calculation of Friction and Wear (in Russian)," Mashinostroenie Moscow, 1977.
32. Uétts, G., " Key findings of studies of abrasive erosion conducted at Stuttgart University," Tr. Tallin. Politekh. Inst. A, 347: 3-21, 1973.
33. Kleis, I. R., " On problems of determining erosive wear in impact with a stream of hard particles," Friction and Wear and Problems of Standardization, Bryansk pp. 219-230, 1978.
34. Biryukov, V. I., Vinogradov, V. N., Martirosyan, M. M. and Mikhailychev, V. N., " Abrasive Wear of Gas-Industry Equipment [in Russian]," Moscow, 1977.
35. Fouvry, S., and Kapsa, P., " An energy description of hard coating wear mechanisms," Surf. Coat. Technol. 138: 141-148, 2001.
36. Li, C., and Yan, F., " Abrasive Wear Behavior of Several Metallic Materials under Simulated Sand-Dust Environment," Proceedings of CIST 2008 & ITS-IFToMM 283-284, 2008, doi: 10.1007/978-3-642-03653-8-88.
37. Bai, L., Qi, J., Lu, Z., Zhang, G., et al., " Theoretical Study on Tribological Mechanism of Solid Lubricating Films in a Sand-Dust Environment," Tribol. Lett. 49 (3): 545-551, 2013, doi: 10.1007/s11249-012-0095-5.
38. Qi, J., Wang, L., Yan, F., and Xue, Q., " Comparative study of microstructure and tribological behavior of TiC/a-C:H and a-C:H coatings in a sand-dust environment," Surf. Interface Anal. 43: 836-846, 2011.
39. Qi, J., Wang, L., Wang, Y., and Pu, J., et al., " The tribological performance of selected solid lubricant films in sand-dust environments," Wear 271: 899-910, 2011.
40. Gore, G.J., and Gates, J.D., " Effect of hardness on three very different forms of wear," Wear 203-204: 544-563, 1997.
41. Hawk, J.A., Wilson, R.D., Tylczak, J.H., and Dogan, O.N., " Laboratory abrasive wear tests: investigation of test methods and alloy correlation," Wear 225-229: 1031-1042, 1999.
42. Sundstrm, A., Rondon, J., and Olsson, M., " Wear behaviour of some low alloyed steels under combined impact/abrasion contact conditions," Wear 250: 744-754, 2001.
43. Qi, J., Wang, L., Yan, F., and Xue, Q., " The tribological performance of DLC-based coating under the solid-liquid lubrication system with sand-dust particles," Wear 297: 972-985, 2013.
44. Bhushan, B., " Introduction to Tribology," Wiley, NewYork, 1997.
45. Qi, J., Wang, L., Wang, Y., Pu, J., et al., " The tribological performance of selected solid lubricant films in sand-dust environments," Wear 271: 899-910, 2011.
46. Jones, G., Armini, A., and Schoen, N., " Selective Radioactive Tracers for Engine Wear Diagnosis and Filter Evaluation," SAE Technical Paper 780972, 1978, doi: 10.4271/780972.
47. Stevenson, A.N.J., and Hutchings, I.M., " Development of the dry sand/rubber wheel abrasion test," Wear 195: 232-240, 1996.
48. Baczewski, K., and Jaroszczyk, T., " Filtration determination of wear process in Internal combustion engines," Proc. 3rd Int. Tribology Conf, EUROTRIB, Lubricants and their Applications, Poland, Vol. III/A, Elsevier, Amsterdam, pp. 7-16.