Film cooling effectiveness and heat/mass transfer coefficient measurement around a conical-shaped hole with a compound angle injection

Proceedings of the ASME Turbo Expo

Volumn 3, Issue , 1999, Pages

  Cho, H H ^a   Rhee, D H ^a   Kim, B G ^a  

^a Yonsei University   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

GAS TURBINES; GEOMETRY; HEAT TRANSFER; NAPHTHALENE;

COOLING PERFORMANCE; CYLINDRICAL HOLES; FILM COOLING EFFECTIVENESS; FILM COOLING HOLE; LATERAL DIRECTIONS; LATERAL SPREADING; NAPHTHALENE SUBLIMATION TECHNIQUE; TRANSFER COEFFICIENT;

COOLING;

EID: 84928501116     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/99-GT-038     Document Type: Conference Paper

References (23)

1. Ambrose, D., Lavmalson, I. J. and Sparke, C. H. S., 1975, "The Vapor Pressure of Naphthalene, v. Chem. Thermo., Vol. 7, pp. 1173-1176.
2. Brittingham, R. A. and Leylelc, J. H., 1997, "A Detailed Analysis of Film Cooling Physics Part IV: Compound-Angle Injection with Shaped Holes," ASME Paper No. 97-01-272.
3. Cho, H. H. and Goldstein, It J., I995a, "Heat (Mass) Transfer and Film Cooling Effectiveness with Injection Through Discrete Holes: PART I-Within Holes and on the Back Surface," ASME J. of Turbomachinery, Vol. 117, pp. 440-450.
4. Cho, H. H. and Goldstein, R. J., 19956, "Heat (Mass) Transfer and Film Cooling Effectiveness with Injection Through Discrete Holes: PART II-On the Exposed Surface," ASME J. of Turbomachinery, Vol. 117, pp. 451-460.
5. Cho, H. H., Jabber', M. Y. and Goldstein, R. J., 1997a, "Experimental Mass (Heat) Transfer In and Near A Circular Hole In A Flat Plate," Int. J. Heat Mass Transfer, Vol. 40, No. 10, pp. 2431-2443.
6. Cho, H. H. and Goldstein, R. J., 1997b, "Total-Coverage Discrete Hole Wall Cooling," ASME J. of Turbomachinery, Vol. 119, pp. 320-329.
7. Eckert, E. R. G., 1976, Analogies to Heat Transfer Processes, in Measurements in Heat Transfer, rd. Eckert, E. R. G. and Goldstein, R. J., pp. 397-423, Hemisphere Pub., New York.
8. Goldstein, R. J., Eckert, E. R. G. and Ramsey, J. W., 1968, "Film Cooling with Injection Through Holes: Adiabatic Wall Temperatures Down Stream of A Circular Hole," ASME J. of Engineeringfor Power, Vol. 90, pp. 384-395.
9. Goldstein, R. J., Eckert, E. R. G. and Burggraf, F., 1974, "Effect of Hole Geometry and Density on Three-Dimensional Film Cooling," Int. J. Heat Mass Transfer, Vol. 17, pp. 595-607.
10. Goldstein, R. J. and Cho, H. H., 1995, "A Review of Mass Transfer Measurement Using Naphthalene Sublimation," Experimental Thermal and Fluid Science, Vol. 10, pp. 416-434.
11. Gritsch, M., Schulz, A., and Wittig, S., 1998a, "Heat Transfer Coefficient Measurements of Film-Cooling Holes with Expanded Exits," ASME Paper No. 98-GT-28.
12. Gritsch, M., Schulz, A. and Wittig, S.,1998b, "Adiabatic Wall Effectiveness Measurements of Film-Cooling Holes With Expanded Exits," ASME J. of Turbomachinery, Vol. 120, pp. 549-556.
13. Gritsch, M., Schulz, A. and Wittig, S.,1998c, "Discharge Coefficient Measurements of Film-Cooling Holes With Expanded Exits," ASME I of Turbomachinvy, Vol. 120, pp. 557-563.
14. Haven, B. A. and Kurosaka, M., 1996,-The Effect of Hole Geometry on Lift-Off Behavior of Coolant Jets," AIAA Paper NO. AIAA 96-0618.
15. Hay, N. and Lampard, D., 1995, "The Discharge Coefficient of Flared Film Cooling Holes," ASME Paper No. 95-GT-15.
16. Honami, S., Shizawa, T. and Uchiyama, A., 1994, "Behavior of The Laterally Injected Jet in Film Cooling: Measurements of Surface Temperature and Velocity/Temperature Field within The Jet," ASME .1 of Turbomachinery. Vol. 116, pp. 106-112.
17. Hyams, D. G. and Leylek, J. H., 1997, "A Detailed Analysis of Film Cooling Physics Part 111: Streamwise Injection with Shaped Holes," ASME Paper No. 97-GT-271.
18. Kim, B. G., Rhee, D. H. and Cho, H. H., 1997, "Heat (Mass) Transfer for Flows around a Film Cooling Jet and a Circular Cylinder with Compound Angle Orientations," 104 Symp. on Transport Phenomena in Thermal Science and Process Eng., Vol. 1, pp. 203-208.
19. Kline, S. J. and McClintock, F., 1953, "Describing Uncertainty in Single Sample Experiments," Mech. Engineering, Vol. 75, p. 3-8.
20. Kline, S. J., Abbott, D. E. and Fox, R. W., 1959, "Optimum Design of Straight-Walled Diffusers," ASME J. of Basic Eng., Vol. 81, pp. 305-320.
21. Lee, S. W., Kim, Y. B. and Lee, J. S., 1997, "Flow Characteristics and Aerodynamic Losses of Film-Cooling Jets with Compound Angle Orientations," ASME J. of Turbamachinery, Vol. 119, pp. 310-319.
22. McGrath, E. L. and Leylelc, J. H., 1998, "Physics of Hot Crossflow Ingestion in Film Cooling," ASME Paper No. 98-GT-I91.
23. Walters, D. K. and Leylek, J. H., 1997, "A Systematic Computational Methodology Applied to a Three-Dimensional Film-Cooling Flowfield," ASME J. of Turbomachinery, Vol. 119, pp. 777-785.