Study of the influence of material properties on residual stress in selective laser melting

24th International SFF Symposium - An Additive Manufacturing Conference, SFF 2013

Volumn , Issue , 2013, Pages 393-407

  Vrancken, B ^a   Wauthle, R ^a,b   Kruth, J P ^a   Van Humbeeck, J ^a  

^a UNIVERSITY OF LEUVEN   (Belgium)

^b Layerwise NV   (Belgium)

Author keywords

[No Author keywords available]

Indexed keywords

3D PRINTERS; MANUFACTURE; SCANNING ELECTRON MICROSCOPY; X RAY DIFFRACTION;

HEAT INPUT; MATERIAL PARAMETER; SELECTIVE LASER MELTING; SURFACE OXIDATIONS;

RESIDUAL STRESSES;

EID: 84898474816     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (31)

1. Kruth JP, Levy G, Klocke F, Childs THC. Consolidation phenomena in laser and powder-bed based layered manufacturing. CIRP Ann-Manuf Technol 2007;56:730-59.
2. Vasinonta A, Beuth J, Griffith ML. Process Maps for Controlling Residual Stress and Melt Pool Sizein Laser-Based SFF Processes. Proceedings of the Solid Freeform Fabrication Symposium 2000:200-8.
3. Vasinonta A, Beuth J, Griffith ML. Process Maps for Predicting Residual Stress and Melt Pool Size in the Laser-Based Fabrication of Thin-Walled Structures. Journal of Manufacturing Science and Engineering 2007;129:101-9.
4. Aggarangsi P, Beuth J, Griffith ML. Melt Pool Size and Stress Control for Laser-Based Deposition Near a Free Edge. Proceedings of the Solid Freeform Fabrication Symposium 2003:196-207.
5. Zekovic S, Dwivedi R, Kovacevic R. Thermo-structural Finite Element Analysis of Direct Laser Metal Deposited Thin-Walled Structures. Proceedings of the Solid Freeform Fabrication Symposium 2005:338-55.
6. Rangaswamy P, Griffith ML, Prime MB, Holden TM, Rogge RB, Edwards JM, et al. Residual stresses in LENS (R) components using neutron diffraction and contour method. Mater Sci Eng A-Struct Mater Prop Microstruct Process 2005;399:72-83.
7. Moat RJ, Pinkerton AJ, Li L, Withers PJ, Preuss M. Residual stresses in laser direct metal deposited Waspaloy. Materials Science and Engineering: A 2011;528:2288-98.
8. Klingbeil NW, Beuth J, Chin R, Amon C. measurement and modeling of residual stressinduced warpage in direct metal deposition processes. Proceedings of the Solid Freeform Fabrication Symposium 1998:367-74.
9. Mercelis P, Kruth JP. Residual stresses in selective laser sintering and selective laser melting. Rapid Prototyping J 2006;12:254-65.
10. Zaeh M, Branner G. Investigations on residual stresses and deformations in selective laser melting. Production Engineering 2010;4:35-45.
11. Nickel AH, Barnett DM, Prinz FB. Thermal stresses and deposition patterns in layered manufacturing. Materials Science and Engineering: A 2001;317:59-64.
12. Brückner F, Lepski D, Beyer E. Modeling the Influence of Process Parameters and Additional Heat Sources on Residual Stresses in Laser Cladding. J Therm Spray Technol 2007;16:355-73.
13. Alimardani M, Toyserkani E, Huissoon JP, Paul CP. On the delamination and crack formation in a thin wall fabricated using laser solid freeform fabrication process: An experimental numerical investigation. Opt Lasers Eng 2009;47:1160-8.
14. Kruth JP, Deckers J, Yasa E, Wauthle R. Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method. Proc Inst Mech Eng Part B-J Eng Manuf 2012;226:980-91.
15. Internal database. LayerWise NV.
16. Amato KN, Gaytan SM, Murr LE, Martinez E, Shindo PW, Hernandez J, et al. Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting. Acta Mater 2012;60:2229-39.
17. EOS. AlSi10Mg material data sheet. 2011.
18. Hastelloy C-276 alloy information. Haynes International.
19. Thijs L, Kempen K, Kruth J-P, Van Humbeeck J. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater 2013.
20. Thijs L, Montero Sistiaga ML, Wauthle R, Xie Q, Kruth J-P, Van Humbeeck J. Strong morphological and crystallographic texture and resulting yield strength anisotropy in selective laser melted Ta. Acta Mater 2013;61:4657-68.
21. Thijs L, Verhaeghe F, Craeghs T, Van Humbeeck J, Kruth JP. A study of the micro structural evolution during selective laser melting of Ti-6Al-4V. Acta Mater 2010;58:3303-12.
22. Murr LE, Quinones SA, Gaytan SM, Lopez MI, Rodela A, Martinez EY, et al. Microstructure and mechanical behavior of Ti-6Al-4V produced by rapid-layer manufacturing, for biomedical applications. Journal of the Mechanical Behavior of Biomedical Materials 2009;2:20-32.
23. Kelly S, Kampe S. Microstructural evolution in laser-deposited multilayer Ti-6Al-4V builds: Part I. Microstructural characterization. Metall Mater Trans A 2004;35:1861-7.
24. Dieter GE. Chapter 15: Residual Stresses. Mechanical Metallurgy. 3rd ed. New York: McGraw-Hill; 1961.
25. Material database. LayerWise NV.
26. Cole N, Gilliland R, Slaughter G. Weldability of W and its alloys: Defense Technical Information Center.; 1968.
27. Deprez K, Vandenberghe S, Van Audenhaege K, Van Vaerenbergh J, Van Holen R. Rapid additive manufacturing of MR compatible multipinhole collimators with selective laser melting of W powder. Med Phys 2013;40.
28. Lippold JC, Nissley NE. Ductility-dip cracking in high chromium, Ni-base filler metals. Hot Cracking Phenomena in Welds II: Springer; 2008. p. 409-25.
29. Young GA, Capobianco TE, Penik MA, Morris BW, McGee JJ. The mechanism of ductility dip cracking in nickel-chromium alloys. WELDING JOURNAL-NEW YORK-2008;87:31.
30. Thijs L, Van Humbeeck J, Kempen K, Yasa E, Kruth J-P, Rombouts M. Investigation on the inclusions in maraging steel produced by selective laser melting. Innovative Developments in Virtual and Physical Prototyping 2012:297-304.
31. Lu SP, Fujii H, Nogi K. Marangoni convection and weld shape variations in Ar-O-2 and Ar-CO2 shielded GTA welding. Mater Sci Eng A-Struct Mater Prop Microstruct Process 2004;380:290-7.