메뉴 건너뛰기




Volumn , Issue , 2012, Pages 499-506

Effect of defects on fatigue tests of as-built TI-6AL-4V parts fabricated by selective laser melting

Author keywords

[No Author keywords available]

Indexed keywords

3D PRINTERS; FATIGUE TESTING; MANUFACTURE; SCANNING ELECTRON MICROSCOPY; TITANIUM ALLOYS;

EID: 84898437374     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper
Times cited : (81)

References (13)
  • 3
    • 0346639199 scopus 로고    scopus 로고
    • Rapid manufacturing and rapid tooling with layer manufacturing (LM) technologies, state of the art and future perspectives
    • G. Levy, R. Schindel, J.P. Kruth. Rapid manufacturing and rapid tooling with layer manufacturing (LM) technologies, state of the art and future perspectives. CIRP Annals-Manufacturing Technology, 52(2), 2003, 589-609.
    • (2003) CIRP Annals-Manufacturing Technology , vol.52 , Issue.2 , pp. 589-609
    • Levy, G.1    Schindel, R.2    Kruth, J.P.3
  • 4
    • 34547491325 scopus 로고    scopus 로고
    • Selective laser melting of biocompatible metals for rapid manufacturing of medical parts
    • B. Van den broucke, J.P. Kruth. Selective laser melting of biocompatible metals for rapid manufacturing of medical parts. Rapid Prototyping Journal, 13(4), 2007, 196-203.
    • (2007) Rapid Prototyping Journal , vol.13 , Issue.4 , pp. 196-203
    • Van Den Broucke, B.1    Kruth, J.P.2
  • 8
    • 84856859388 scopus 로고    scopus 로고
    • Analysis of fracture toughness and crack propagation of Ti6Al4V produced by selective laser melting
    • B. Van Hooreweder, D. Moens, R. Boonen, et al. Analysis of fracture toughness and crack propagation of Ti6Al4V produced by selective laser melting. Advanced Engineering Materials, 14(1-2), 2012, 92-97.
    • (2012) Advanced Engineering Materials , vol.14 , Issue.1-2 , pp. 92-97
    • Van Hooreweder, B.1    Moens, D.2    Boonen, R.3
  • 10
    • 78049508809 scopus 로고    scopus 로고
    • Ductility of a Ti-6Al-4V alloy produced by selective laser melting of prealloyed powders
    • L. Facchini, E. Magalini, P. Robotti, et al. Ductility of a Ti-6Al-4V alloy produced by selective laser melting of prealloyed powders. Rapid Prototyping Journal, 16(6), 2010, 450-459.
    • (2010) Rapid Prototyping Journal , vol.16 , Issue.6 , pp. 450-459
    • Facchini, L.1    Magalini, E.2    Robotti, P.3
  • 11
    • 84856406269 scopus 로고    scopus 로고
    • Metal fabrication by additive manufacturing using laser and electron beam melting technologies
    • L.E. Murr, S.M. Gaytan, D.A. Ramirez, et al. Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies. J. Mater. Sci. Technol., 28(1), 2012, 1-14.
    • (2012) J. Mater. Sci. Technol. , vol.28 , Issue.1 , pp. 1-14
    • Murr, L.E.1    Gaytan, S.M.2    Ramirez, D.A.3
  • 12
    • 0035482538 scopus 로고    scopus 로고
    • Behavior of alloy Ti-6Al-4V under pre-fretting and subsequent fatigue conditions
    • W.A. Glaeser, B.H. Lawless. Behavior of alloy Ti-6Al-4V under pre-fretting and subsequent fatigue conditions. Wear, 250, 2001, 621-630.
    • (2001) Wear , vol.250 , pp. 621-630
    • Glaeser, W.A.1    Lawless, B.H.2
  • 13
    • 0033100477 scopus 로고    scopus 로고
    • Fusion zone microstructure and porosity in electron beam welds of an α+β titanium alloy
    • T. Mohandas, D. Banerjee, V.V Kutumba Rao. Fusion zone microstructure and porosity in electron beam welds of an α+β titanium alloy. Metal. Trans. 30A, 1998, 789-798.
    • (1998) Metal. Trans. , vol.30 A , pp. 789-798
    • Mohandas, T.1    Banerjee, D.2    Rao, V.V.K.3


* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.